0
Chevy Blazer
The Chevy Blazer may refer to any of the sport utility vehicles manufactured by the Detroit-based automaker General Motors Company. Some of the popular Blazer models produced by the company are the TrailBlazer, the S-10 Blazer and the K5 Blazer.
5,824 Questions
I had this problem- it is a simple fix. The problem is at the base of the gearshift. There is a small electric metallic contact that releases the key when you shift into park. that contact can become gummed up and not work properly causing the car to not release your key. (the contact does not engage and the car thinks you are not in park...) If you unscrew the center console and pull it off over the gearshift you will see the contact on the right hand side at the base of the shift lever. I used a little WD-40 to clean it and voila! No problems since. It took me 10 minutes and 2 squirts of WD-40.
How do I open hood from outside when hood release lever is broken from inside 1987 BMW 325i?
These cars have hoods that open on the windshield side with the hinge toward the bumper. Apparently I'm not the only one having this problem Generally, cars have a manual hood release latch just inside the grill of the car, under the hood.
Can you do away with most of the vacuum lines on your 1985 Chevy 305?
some yes...but it depends on whats happening. if its your egr, or pcv, vacuum break...(in other words, something is stuck) best bet is to take about $40 or so to the parts store, get 1 new egr, 1 new pcv, etc... and about 10ft of 1/4 vcuum line (the employee should know how to cut that). IF U WANT... u could start by taking a pocket knife to your vacuum line(s) where they are connected (only if they're cracked/broke, rotted) make a clean cut and slide back on to see if that cures a problem u might be having...
but if your looking to just get rid of vacuum lines...--> try unplugging 1 at a time with the motor idling. BUT BEWARE!!!! this could screw up your idle, fuel mix, possibly start causing overheating, etc. I know they suck, but they're pretty well needed.
This can be attributed to a couple of things. In order to remove the key you can remove the plastic piece under the ignition switch to expose a key release button. OR you can drill out the small circle in the area below the ingnition switch to access the key release button.
The stuck key may be a faulty ignition switch or a bent shift lever. This causes the lever to not make the release solenoid contact. If you slammed it into park you make have bent the contact point on the control arm.
Faulty ignition switches are a common failure.
What to do to take antitheft system off chevytrail blazer?
To disable the antitheft system on a Chevy Trailblazer, you can try unlocking the vehicle with the key fob or using the physical key in the driver's door. If that doesn't work, disconnecting the vehicle's battery for a few minutes may reset the system. Additionally, if you have the owner's manual, it may provide specific instructions related to your model. For persistent issues, consulting a professional mechanic or a dealership is advisable.
What temp should your 86 blazer with a 350 operate at?
Between 180 and 195 degrees is the safe range.
Where is a oil sending unit for a 1985 350 Chevy Silverado located?
In back of the engine, on top, drivers side, next to the distributor.
Where is the idle speed motor located at on a 1995 Chevy blazer?
Where is the idle speed motor located at on a 1995 chevy blazer?
Why on a 2000 Blazer after 4200 rpms the reb limiter is kicking in?
It will if you are free reving the engine with out it being in gear.
If you are driving it hard down the road and it is kicking in then you may need to have the engine scanned with an OBDII engine scanner and make sure you don't have a problem in the system.
What is wrong with a transmission on a 01 blazer wont go into reverse but goes into drive?
You blew your transmission, took out the reverse gear. You'll have to take it to a tranny shop and get it rebuilt (not cheap), or replace it yourself with one from a scrap yard. ($600 in parts, a weekend to do it)
What type of hitch is used to distribute tongue load to all towing vehicle and trailer wheels?
It is generally termed an 'equalizer hitch'. There are several companies that manufacture them. There are torsion bars that hook solidly to the hitch, and the trailer connections are chains, so you can adjust the amount of weight you want to transfer.
In about 1966, there was a promo ad showing an Olds, Toronado (front wheel drive), with its back wheels removed, towing a vacation trailer. Looked a little goofy, but sure illustrated the point!
What is the largest size tire and rim you can fit on a 1993 Chevy Blazer S-10?
I have 20" Dayton wires on my 84 s-10 4x4 blazer with 225x50x20 and it rideas fine. I have 20" Dayton wires on my 84 s-10 4x4 blazer with 225x50x20 and it rideas fine.
This can be done, though some modifications may be needed. If you need to replace your core support (rad support) as well, order a core support for a 91 S10 blazer. This will help do away with the mounting issues.
I did this to a 1985 S10 blazer and the grill fit fine with the factory core support, but not all of the mounting locations matched.
Will a double din receiver fit a 2000 s-10 Chevy blazer?
yes but you will need a 03 radio trim and do a little cutting
Where is the firewall in a 1997 blazer?
The separation between the engine compartment, and you, is called the firewall. The Steering shaft, from your steering wheel runs through the firewall, the heater hoses run through the firewall, the power brake vacuum unit is connected to the firewall, your ignition wires etc run through the firewall.
Why is A 1996 blazer making a buzzing noise when started and when idling?
Check the 1996 Blazers power steering pump. When the pumps go bad they will start to whine or buzz.
Set timing 2002 blazer EDI distributor?
how do you set the timing on a distriubtor for a 2002 Chevy blazer
Quite possibly a failed fuel pump. What you would have noticed was the engine misfiring then stalling. It happens pretty quickly and you would not hear a thing. vbd that or running out of fuel. could also be that your throttle valve cable near the carb needs to be adjusted or replaced. this would cause your car to lose power and/or delayed shifting of the the transmission, usually accompanied with a loud noise when pressing the gas pedal
If the key stuck is stuck in the ignition of a 1994 Saturn SL1 is there a release for the key?
1b. If there is not a small removeable plastic piece, remove the housing around the steering wheel (this may require removing a few screws), and look for a white button directly under the steering wheel.
2. Hold it down and the key will turn with ease.
Permanant FixKeeping this button held in will solve the problem.How do you remove the dashboard of a 2002 LS Blazer?
how do you remove the dashboard of a 2002 Chevy blazer
