0
Chevy Cheyenne
Launched in 2003 at the North American International Auto Show, Chevy Cheyenne is a concept car manufactured by General Motor’s Chevrolet brand. It features innovative technology not used in any vehicle yet such as its unique cargo bed and side access doors.
1,327 Questions
Where is the clutch slave cylinder on the 1992 Chevy Cheyenne?
It is mounted on the transmission bell housing by 2 bolts. The clutch master cylinder is mounted on the drivers side fire wall.
1994 Chevy k2500 just did clutch slave and master cylinders and wont engage why?
Just had same problem and replaced both also. Still not engaging. Thought I was going to have to replace clutch due to bad pressure plate. Took transmission off engine and the release fork for the clutch had worn through on the pivot point. This is a recurring problem from what I have searched. Has to be replaced and a ball pivot replaced also for the release fork. Both are dealer parts if you want the right parts for the job. Searched after market but ones I looked at did not meet the size I needed. Good luck.
Why is the AC Light on 92 Chevy Pick Up flash and blows hot air?
That's usually an indication that the refrigerant level is low.
How do you replace fuel injectors on a 98' GTP Can you tell if they are bad?
Check out the following website for pics and a description on how to complete this task.
http://www.clubgp.com/newforum/TM.asp?m=3076805&p=1&tmode=1&smode=1&cookieCheck=156943076
(courtesy of www.clubgp.com)
There are vendors that will change the "O" rings and clean/inspect the injector flow -for example:
http://www.witchhunter.com/index.php4
Hope this helps.
"G"
What is the Valve cover bolt torque on Chevrolet 250?
15 ft. lbs. torque in specific sequel criss-cross careful not to over tighten cause it will squish the gasket and allow for leakage.
What are the symtems of a bad fuel injector on a 1992 buick park ave?
hard to start misfires idles rough or not at all lack of power or acceleration poor fuel economy
What do you have to do to remove a starter for a 1988 Chevy Cheyenne 6-cylinder standard trans?
you must remove the clutch slave cylinder and line. Then unbolt the starser and install the new one
This is the sensor that is usually built into the Mass Air Flow (MAF), or screws into the airbox. It measures the intake temperature so the engine can adjust different things, such as fuel, so the engine is running at its best.
Where can you find a diagram of an 1989 Chevy Cheyenne rear differential?
was driving down the road in my 1989 chev truck 1500 and heard a noise of some kind from my rear-end and then the rear wheels would not spin
White reverse tailgate lights don't come on when you back up - is there a bad fuse?
Check out the backup light switch on the left side of the transmission gearbox beneath the truck. Buy original switch, aftermarkets seem to fail. Please inform the result; awaiting original switch.
How do you remove drive shaft from your 1993 Chevy Cheyenne 1500?
The rear shaft is removed by lifting the rear of the truck off the ground and safely supporting it on jack stands. Remove the four retaining bolts ( 7/16" wrench )from the yoke on the front of rear differential. You may have to put truck in neutral to allow the drive shaft to be turned to gain access to all the bolts. You may have to pry the u-joint out of the yoke, being careful not damage anything, or knock the bearing caps off. Some can really put up a fight coming out of the yoke. Place a catch pan under transmission tail, and slide the drive shaft out of the transmission. You may get a small amount of leakage from the tail, but should not be bad ounce or two. If you have a front shaft ( 4x4 ), lift the front end up four bolts on each end, 7/16" wrench, 5/8" wrench on transfer case. There is no oil lost removing the front shaft.
What causes a Chevy C2500 to run rough while driving?
Fuel filter, air filter, gas line leak, charcoal filter or line, spark plugs, and timing..
I cant think of anything els right now, Good luck
I'd start by checking for vacuum leaks.
Hey Eddie==Check the light switch to make sure it is turned correctly to keep it off. If ok, check the lighter fuse, as if it blows sometimes it turns the light on. goodluckJoe If your tailgate is ajar it will also cause the light to stay on.
How do you remove a water pump from a 1998 Plymouth Breeze?
Once that is done, you need to place a jack under the engine using a block of wood and take pressure off the motor mount. Once that is done, remove the motor mount on the right fender wall. You will also need to remove some of the clamps holding hoses and A/C lines in place to move them out of the way. Once the motor mount is out of the way, you need to remove the upper timing belt cover. After that is done, you will need to remove the aluminum motor mount base from the engine to gain access to the timing belt. Once all that is out of the way, you will need an Allen Wrench to release the belt tensioner on the timing belt. (note: BE SURE that the engine timing marks are set in alignment with there corresponding marks on the block and the timing belt pully!!)
There is a hole on the left side of the tensioner which you need to place a pin or smaller Allen Wrench in to lock it in place after you remove the tension off the timing belt. You push the pin in toward the block to lock the tensioner.
Remove the timing belt (which you might as well replace seeing you've gone this far anyway). You then will be able to remove the five bolts holding the water pump in place which is run off the timing belt (yes, it's a nightmare). Replace the water pump and put it all back together.
Good Luck.
Normally a whining noise in the back end means the differential is shot
Where can you find color code for Dodge PU wiring?
Try the Dodge Manual.. I found lots of helpful info at the local library.
WHAT COULD BE WRONG WITH 1988 Chevy Cheyenne 1500 heater defrost and ac all stopped working?
Check your fuses!
well the forst thing I would do is NOT even attempt this. your non digital setup is not wired at all for this so EVERYTHING in the system would need to be changed because the digital uses a logic board and the other does not. unless your a very good engineer or plan to redo all the wiring to make it acceptible for computer components i would say just leave well enough alone. many streetrodders use modern digital in the rods but its real difficult unless you have an new harness or alot of friends with patience. if you insist on this project maybe try to find another truck that was totalled and maybe you can get the harness. good luck.
What is the towing capacity of a 1995 Chevy Cheyenne 2500?
It should say in the glove compartment. My 95 says 1885 lbs. With the 5.0 liter
How do you remove the fan bolt from the water pump on a 94 Ford Ranger 6.0?
Your auto parts store usually has a kit you can rent that has a wrench and spanner that allows you to hold the pulley while you loosen the nut. Quick and easy. Just ask for a water pump pulley removal kit.
What kind of manual transmission fluid goes in a 95 Chevy Cheyenne 1500 5 speed?
Synthetic syncromesh manual transmission fluid either gm parts has it or ams oil does. The key is syncromesh tho any aftermarket oil thats syncromesh.
Could you tell you how many bolts are in the intake manifold on a 93 ford probe?
If its the v6 there are 8 bolts and 4 nuts.
