0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
How long to change a cranksharft sensor on a Renault espace?
it sits on top of the gear box it has one plug and two bolts that hold it on so disconnect the battery undo the plug undo the boltd put the new one on and re connect plug and battery
Where is the iat sensor located on a 1994 Mitsubishi eclipse gs?
The IAT is integrated in the Mass Air Flow (MAF) meter. It's the coffee can in the front passenger side of the car. It's a brown connector and on a GS it should have 6 wires where as on a GST/GSX it has 7 wires.
What is the function of the crank sensor?
the crank sensor "tells" the computer what piston is at the "power stroke" and what coil to fire also the next cylinder that is going to need fuel.
How do you reset brain after crank shaft position sensor has been replaced?
i normally disconnect the battery for a few seconds, or pull the battery fuse, or buy a code reader and reset it that way
Where is the crank shaft position sensor on a Daewoo Leganza?
On the Daewoo Leganza it is located behind the AC compressor.
Where is crankshaft sensor on Renault clio mk 1?
On the right side, above the gear box. I is placed behind the pipes of the cooling system.
Where is the camshaft sensor on a 1996 Chevy Z-71 truck with a 305 engine?
Back of the motor near the fire wall. Follow one of the wire sets from the distributer to the sensor.
Where is the crankshaft sensor on a 92 Chevrolet Lumina 3.0L?
ANSWER..........It's in a hard to find place; get it from under the car, its in between the oil pan and the trany. At the top of the oil pan in the block on a downward angle. There are two other thinges in the block just above it to the right. (looking from under the car)
Code P01320 means Ignition signal primary cicuit fault.
After replace all that stuff did you go back in the OBD and clear the codes?? If not that's probably why its still pulling the same code
How often do you need to replace cam shaft positioning sensor?
only when bad.....not a maintenance item
Where is the distributor on a 1993 Mazda MX6 and what would be a fair price to repair?
its on the front of the engine, on the drivers side of the head. they usually cost about 200-250 new and would not take a mechanic more then 1 hour to replace. so cost +labor= how much u might expect to b charged
Where is the crank position sensor on a 1999 Chevrolet Malibu?
The 1999 Chevrolet Alamo crank shaft position sensor is located on the back of the engine. You will need to remove the rear engine cover in order to access the crank position sensor.
Where is the crank position sensor located in a 1999 Jeep Grand Cherokee 4.7 liter V8 petrol?
And a pain in the butt to get to without having the jeep on a lift. make sure when reinstalling the sensor that the wires are not coming into contact with your exaust manifold or the exaust pipes. they will get hot and melt down to the wire and ground out causing the sensor to fail.
My Personal Experience
For Grand Cherokee Jeep Limited 1999/2000, the CKP sensor is located on the right side (driver side) at the end of the engine block when you open the hood and facing the engine block..the sensor sits on the bell housing..It has its cable connector end pulled all the way to the left side of the engine block and connected there, so you may have to first locate and grab that connector cable end, near the oil filter at that left side at the end of the engine block , and then you feel and trace the connector cable all the way through the back of the engine block back to the CKP sensor on the right end side of the engine block in order to easily locate the sensor. whew!
Now, I have to warn you that its very difficult to replace the CKP sensor no matter what anyone tells you.. because you will have to lift the car axle up and get underneath the car to have some access to the sensor..even with that.. you will need foot long screwdrivers, 1/8 wrench , handy light for illumination and all kinds of difficulties in avoiding mutliple cables along the way in order to get to the sensor and unscrew it out..and that's not all.. its very difficult to put a new one back in too once you remove the sensor!..you may have to glue bolts/screws to your wrench and screwdrivers to make a fix back..they keep falling off due to odd angle of access to where you need to screw them in....I tried to do it..It was very difficult..
My suggestion, don't spend your valuable time trying to do this replacement part..just order online your CKP sensor ($55) and get a freelance mechanic to fix it for you..labor cost is around $70 and it only takes about 45mins for a good professional to replace the sensor.. much easier and faster that way.
Where is the camshaft position sensor in 1998 kia sportage?
The cam shaft position sensor is located right behind the exhost cam by the fire wall. It is held by two 10 mm bolts, one on each side of the sensor. If you got the hood up and looking at the engine the cam that is on the right hand is the exhost cam. To get to the CPS you have to remove the intake and cam top cover.
Where is crank shaft position sensor on a 2000 jeep grand Cherokee?
Do you have a 4.0l (6 cyl) or a 4.7l (V-8). I just changed one on a 2001 with the 4.7L v-8. It is located on the passengers' side behind the starter. on the 4.0 it is located on the top of the bell housing on the drivers side.
Can you drive your car with camshaft sensor is bad?
Well basically you can "do" what ever you want, but if you wanted to be on the safe side I'd suggest you fix the car first.
Submitted from your friend, Ashley:)
On a 1996 Nissan Maxima which O2 sensor is Bank 2 Sensor 1 since there are three sensors?
Bank 1 Sensor 1: Located on rear exhaust manifold pipe nearest the firewall. Fairly easy to remove with the right tools. Clip located on left side of engine compartment.
Bank 1 Sensor 2: Located just behind the Catalytic Converter. Very easy to remove and clips on just inside rubber gromet.
Bank 2 Sensor 1: Located on front exhaust manifold pipe nearest the radiator. Hard to reach without specific tools. Clip located in front of engine compartment.
Bank 1 = both front firewall-side sensor (1) AND rear sensor (2). Bank 2 = front radiator-side sensor (1). Bank one refers to the section of the manifold that vents exhaust from the cylinder bank including cylinder #1...bank two = from cylinder #2 and its comrades.
Where do you locate the crank shaft censor on Renault clio 96 m reg 1.4 auto because its faulty?
The crankshaft position sensor can be found on the back of your 1.4-liter engine. You will need to remove the rear engine cover in order to access the crankshaft position sensor.
the sensor should be located behind the raidator right above the starter
the sensor should be located behind the raidator right above the starter
How do you start your car with bad crank sensor?
Usually not at all. If the Engine Control Unit does not get signal from the Crankshaft Sensor it will not know when to inject fuel or light it with a spark. Consequently it will not start.
Where is crank position sensor on a 1999 dodge 5.2 liter truck?
Top of the bell housing, behind the passenger side cylinder head. It is almost under the transmission dipstick tube.
Where is the crank sensor located on a Lincoln ls v6 engine?
where is the crankshaft sensor location on a lincoln ls v6 2003
