0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the crankshaft position sensor on a 2002 Dodge Dakota 3.9L v6?
The crankshaft position sensor goes through the bellhousing behind the passenger side cylinder head.
The crankshaft position sensor goes through the bellhousing behind the passenger side cylinder head.
Where is the crank sensor on my 1996 Subaru Outback legacy?
Directly below the alternator on the block.
What is crank Design and Tegnology?
crank is nothing but disk and it is a rotating part and it is couple with crank shaft
Try AUTOZONE.com. They have a parts locator and service manual -- no cost.
How do you change a camshaft position sensor 1995 Ford Windstar?
Disconnect the electrical connector. Remove the two 7/32 screws holding it on, and replace it. On the 3.8L it is like a little distributor at the front of the engine in the top of the timing cover. It has been a while but I think it just has one screw and clamp holding it in. You should also have the engine on TDC #1 and mark the old one before you pull it out. This makes life a lot easier if the engine would by chance turn with the sensor removed. MGL
Could a crank shaft sensor cause my 2005 Nissan Maxima to go into limp mode?
A bad crankshaft sensor would stop the engine and not restart.
Where is the crank position sensor located in 1997 dodge caravan?
4 cylinder : back of the block 6 cylinder : top of bell housing, about 2 0'clock if looking over drivers side.
Where is the camshaft position sensor on a 2001 Kia Rio?
It is on top drivers side just right of the exhaust manifold. It has one bolt and a cannon plug that has a clip that has to be removed before you can take it off
Why does a crankshaft sensor have intermittent loss?
intermittent loss indicates you need a new sensor
Cam sensor on a 2001 Cadillac Seville?
A cam sensor for a 2001 Cadillac Seville can be purchased at any auto parts store. The prices will vary depending on location and brand. Prices start at $31.99 for the part.
Where is the crank sensor on a 1999 Chevrolet s10 2.2 truck?
On the engine block, passenger side, close to the oil pan. It is best reached from underneath.
Where is the crankshaft position sensor located in a 2003 Hyundai santa fe 2.7L?
2003 santa fe 2.7 what could cause The engine whilein park the idle is smooth when in gear engine has intermttent miss & hesitates on acceleration with minor backfire
Where is the cam position sensor located on a V W Passat?
Maybe this will help a little.....I know its not the same year....
On my friends 2002 V W Passat, its located at the end of the head. The round cap/ electrical hub, on the camshaft.
^^
Where is crankshaft position sensor located on a 1996 Toyota corolla 1.6 liter?
Near the bottom timing belt cover (on the top left).
Can you bypass the seatbelt sensor in a 1991 VW Golf?
Obviously, buckling the seatbelt should silence the reminder. If you see/hear the reminder and all belts used by the reminder ARE buckled, the vehicle should be taken in for service ASAP. If you do not want to use your seatbelt and wish to disable or silence the reminder system altogether, this can be done in a matter of minutes by a serviceperson at a dealership using a custom option setting device connected to the vehicle's internal computer. As this is a safety system, some dealerships may not be willing to do this unless you sign a liability waiver. If you do not wish to have the vehicle serviced professionally for whatever reason and would like to disable or bypass the seat belt reminder system for certain seats only, the following options may be of help: A piece of sheet metal of the same dimensions and shape as the actual seat belt 'plug' can be inserted into the seat belt 'socket' to silence the reminder. Obviously, the more the piece of metal resembles the actual 'plug', the more likely it is to work. Also, as seat belt buckle design has not changed much lately, a junkyard is one source of seat belt 'plugs' that can be cut from their straps and inserted in the seat belt 'socket' to silence the reminder chime. It's likely that several model years of a car (and even different makes/models) may all have similar seat belt 'plugs'. Lastly, there are wires running down the 'socket' end of the seatbelt which tell the car's computer if the seat belt is buckled or not. These wires may be cut, stripped and connected together (or separated, depending on which stops the reminder) permanently. It should be mentioned that disabling or bypassing this safety system in any way is discouraged by vehicle manufacturers, insurance companies, safety specialists and many other private and public organizations and individuals. However, there are conditions for which seatbelt use is extremely uncomfortable or presents more harm than benefit, such as in the case of certain abdominal/thoracic medical conditions, morbid obesity, etc.
How do you change the crank position sensor on a 1998 Grand Prix GT 3800 series II?
Remove the drive belt, remove the crank pulley (need a special puller for this), remove the plastic shield, and finally remove the two bolts that secure the sensor to the engine. This is all done through the passenger side wheel well with the wheel removed.
Where is the crankshaft position sensor located on a 1996 Dodge Grand Caravan with 3.3 liter engine?
Just trying to help in my caravan its about 5 inches behind the crank pully but you might have to go under the van to locate it.
On a 3.3L it goes through the bell housing.
Is there a sensor that would cause the engine to shut off on a Geo Metro?
Look at one of the 3-4 big fuses under the hood, drivers side by the battery.
