0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the camshaft position sensor on a 1997 Chrysler Sebring?
V6 it is inside the distributor. Four cylinder, it is on the driver side of the cylinder head.
V6 it is inside the distributor. Four cylinder, it is on the driver side of the cylinder head.
Car starts fine but dies after 10 seconds every time?
sounds like an immobilizer fault or the battery in your key is faulty
Where is the crankshaft sensor located on 1997 Infinity I30?
location of crankshaft sensor on 1997 Infinity I30 is it on the engine or in the gas tank plz show a pic
The circuit they control is being overloaded or has some sort of fault.
It is caused due to higher amount of electricity passing through the fuse than it's specified capacity.
You have spark and fuel but it wont start?
It may have wrong timing. May be, the electrical wiring are not fixed properly, e.g, they are opposite. There can be different reasons.
i was chasing down a tail light problem and blue a fuse. i still have that problem?
fusible link?
Where is the cam shaft position sensor on a 2001 Olds Alero?
The camshaft position sensor is right under the power steering pump. Remove the power steering pump to access the sensor.
I'm not familiar with, and don't have any experience with your vehicle, but the key clue in your question is that it will "fire" when applying starting fluid.
This clearly indicates that the problem is that fuel is not getting to the cylinders. There could be many causes for this, and without being able to do a "hands on troubleshooting" of your vehicle none of us on this site can tell you what that specific defect is.
Here are some of the things I can think of that could cause fuel starvation:
- Leaks in fuel system allowing air in which can inhibit fuel flow,
- Pinches or kinks in fuel lines or hoses which cut off fuel flow,
- Blocked fuel filter, or filters,
- Fuel pump, or pumps, not working,
- Clogged filter screen in fuel pickup line in fuel tank [s],
- If a carbureted vehicle, float valve stuck closed,
- Small passages [called "galleries"] inside the carburetor clogged/blocked,
- If a fuel injected vehicle, the electronic control defective not allowing fuel to pass.
There are probably other causes which escape my mind right now.
how do u change a crankshaft sensor on a Oldsmoilbe alero 2001 2.4L twin cam?
What is the cheapest way to fix a leaking radiator?
I would say the most inexpensive way to repair this is to get a good used radiator at a salvage yard near you. If you're handy with wrenches you should be able to save yourself some BUCKS $$ going this route.
__
I would buy a new one if I were you. Salvage yard ones have been sitting around with no coolant, rotting. You want to take the chance of destroying your motor? A used one will go bad soon too. Might as well start fresh.
--
Stop-Leak is the cheapest way to fix a small leak, but it is only a temporary measure. If coolant is really gushing out of the radiator, it's best to replace it or have a radiator shop repair it. Trying to cut corners here is like jumping over dollar bills to pick up pennies. BUY A BRAND-NEW VIRGIN, FRESH-FROM-THE-FACTORY RADIATOR!! Most come with a warranty. It is risking severe overheating and possibly blowing a head gasket or destroying your motor. $100.00 for a new radiator is much cheaper than $1000.00 or more to replace a head gasket or a motor.
_
For a small leak idle engine, top radiator with water crack open a fresh egg and drain into radiator.
this might sound funny but if you cant afford to buy a new one at this time you need it try black pepper in it,works like stop leek and is cheaper,and you can get it anywhere.
How many hours do it take to change a crank sensor on a Mitsubishi galant 2.4 engine?
Check with a "good" mechanic. They will hav a aual that outlines the average "shop" time to make this repair. They will give this info to you no chage.
What is the torque value for the crankshaft pulley on a PT Cruiser?
The torque value is 100 ft.lb. or 136 n.m.
Replace crank position sensor 05 Nissan Altima?
Here is the link where you can see how to install Crank shaft positioning sensor with detail pictures.
http://dentnshell.com/Projects/2005Altima/CamkPosition.html
How much horsepower can a granny for speed handle?
about 2 to 3 horse power at the maximum. if any faster wrinkles wil be flattened and sag behind
both are under forward exhaust manifold.
Where is camshaft position sensor located on a 1999 ford ranger?
On a 1999 Ford Ranger :
You don't mention the engine size but from what I have read the camshaft position sensor for the 4.0 liter EFI , V6 engine ( which is an Over Head Valve / pushrod design engine )
Is on the top of the engine , near the centerline , at the back of the engine near the firewall
* apparently you can't see it until the upper intake manifold is removed
Where is the crank sensor located on 2006 Hyundai Tucson?
In the right side of motor, at drivers side, near the exhaust manifold. I is very dificult access it.
Could the crank shaft position sensor cause stalling problems on a 2003 Expedition?
I have finally fixed my stalling problem in my 2003 ford expedition and wanted to share the repair with you, first of all for the safety of our families, and the cost of everything the mechanics think is wrong (even most ford mechanics are not aware of this fix) I have been lucky and never did the coil packs, fuel pump and new throttle body and valve. I did waste money on the camshaft sensor and IAC control valve; I did keep the old one so I have a back up if I need it in the future. I didn't try the high octane fuel fix because I heard of this year throwing spark plugs which are big bucks to repair. Putting on this part and looking at the old one makes me think I didn't even need a new one, but didn't know what to expect when I bought it. The bracket connects the alternator to the positive terminal on your battery. If you start at the battery + terminal it has 2 red wires coming out of it. They are both usually red and about the same thickness. One of them goes into a long black rectangle clip that says "fusible Link" or something like that. Then comes out the other side and goes to the alternator. Past the fusible link box there will be 2 wires that split off of this wire. If you are in front of the truck one wire runs towards you and is pretty short. It plugs into another wire. The second wire is longer and it runs away from you THIS IS the wire you need to follow. It runs back towards the battery into a plug under it. Follow this wire from where it comes off of the big wire. You will find it resting on a silver/aluminum tube (its an AC pipe) Flip the wire over where it is touching this pipe, you will find the wire is rubbed down to the bare metal! It is randomly shorting out your engine and you will STALL. If I didn't by the part I would try to tape it up, tape the pipe it rests on as well or get some foam tubing for the pipe, if the wires are too worn, looks like you could always use a wire nut.
Location of the crankshaft sensor on a 1998 Buick Century?
the crankshaft position sensor is located right behind the harmonic balancer mounted on the timing cover
What can cause cam shaft problems?
Camshaft problems can be caused by several factors, including inadequate lubrication, which leads to increased wear and tear, and misalignment during installation. Additionally, using poor-quality or incorrect timing belts or chains can result in camshaft damage. Overheating due to engine issues can also warp or break the camshaft. Lastly, excessive engine modifications or high-performance upgrades without proper adjustments can stress the camshaft beyond its design limits.
How does a camshaft position sensor work and how can you get it to set a code without unplugging it?
the cranshaft and camshaft position sensor.
the engine speed and cranshaft position information is supplied frome a sensor which is usually situated at the front or rear of the cranshaft.note that distributor-located engine speed sensor are generally being replaced with cranshaft-located sensors,as worn disributor drives and associated components can effect the accuracy of the engine speed signal.
A camshaft position sensor,or cylinder identification sensor is used to determin the engine cycle position the information is used to provide individual cylinder ignition and injection cotrol.Many engine management systems use an inductive type of sensor that is located near the camshaft;when the camshaft rotates a single signal is passed to the ECU to indicate a reference point in the engine cycle.Some system manufactures may use a Hall effect-type sensor.
Where is the crankshaft position sensor on a 1995 Chevy Blazer?
The 95 don't have one. It was not used untill 1996
How do you remove the door crank on a Kia Sephia?
From reading some other posts in another chain , "you push the panel in and remove the clip on the crank..
