0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
Where is the crank shaft sensor on 2004 Hynudai Sante Fe 2.4 engine?
It is under the timing belt cover near the crankshaft pully / harmonic balancer.
Where is the crank sensor located on a 1995 dodge ram?
The crank sensor is located on the passenger side of the bell housing near the valve cover. It is held in place by two Allen head cap screws.
Where is the crank position sensor on 2001 vauxhall Astra 1.7 DTi 16V?
Crank sensor is best viewed from under car,its above offside drive shaft and a pain to get to,held in with 1 torx bolt
How do you remove the crankshaft pulley for1983 Mazda 929?
One useful trick for removing the crank bolt on the crank pulley is to place a breaker bar with socket (highly recommend a 1/2" setup in the minimum as 3/8" sockets don't fair well with high amounts of torque) on the crank bolt so as the handle of the breaker bar is resting against the frame of the vehicle and the socket is firmly on the crank bolt. Do bare in mind that the engine turns clockwise (some few motors do turn counter clockwise-- please check service manual to determine direction of rotation) as this will affect the location of the handle. Once the breaker bar is in place you will want to "bump" the motor or in other words start the car but only long enough to allow one or two rotations of the engine and absolutely no more. Once this is done the crank bolt should be finger loose. This information is provided in that the bolt may be holding you back and with the utmost caution as this is a risky procedure in which someone could be hurt by flying tools or that damage may occur to the crank bolt or frame if poor judgment is used in the correct placing of the tool. Otherwords, make sure the socket is firmly on the bolt and that the handle is not going to crush something weak such as a plastic piece or something of the sort. Good Luck!
Where is the camshaft position sensor on a 1996 Thunderbird LX?
on the front of the motor. lookes like a small distributer. it black and round.
Does a faulty crank sensor or cam shaft sensor cause excessive oil use?
NO it will not. They have NOTHING to do with oil usage.
Where is the crankshaft position sensor located on a 1991 Dodge Dakota?
i have a 92 Dakota and the sensor was behind the engine closer to the passenger's side, if you want to get that becauseyour truck is stalling you should also consider buyin a computer, because i tried a bunch of stuff, and the computerwas the source of the problem
Where is the crankshaft positioning sensor located on a 2003 Chevy suburban 5.3L?
Same as the Tahoe behind the starter
P1345 crankshaft position camshaft position correlation?
Replace the crankshaft and camshaft senors and then clear the codes with an oBD II engine scanner and that will fix it.
If the crankshft sensor is bad will the car start at all?
I can tell you what happened with my Buick. The crank sensor was bad. The engine would start when it was cold but not when the engine was hot. Warner athey The engine computer needs the crank sensor reading to start. Period. Why three periods? Question mark? If the crank sensor is bad that does not mean that it will not function at all. That means that it will not function properly. Even a broken watch will tell you time. It may even be the correct time.
You would like to locate cam shaft sensor and crankshaft sensor for 1991 dodge caravan 3.0?
Crank sensor is in the top of the transmission housing at the back of the engine.
Cam position sensor is in the distributor.
Where is the crankshaft sensor on a 1997 Chevy silverado with a 350 engine?
it is under the roter cap.
Can the camshaft sensor cause an engine to sputter?
Yes, that and dozens of other causes.
Yes, that and dozens of other causes.
Where is the Crankshaft Position Sensor on a 2000 eclipse RS 4-cylinder?
it's on the right side of the engine at the very top. it would be closest to you. there is a electronic harness clip that slides into it. it's right above the EGR exhaust port and to the right.
Could you please tell you On a 1998 Isuzu rodeo 3.2l v6 where does the cam shaft sensor connect to?
a two prong female wire connector coming from the left side wiring harness at the top of the motor. one of the two wires is orange.
Where is the crank angle sensor on a 1990 Mazda rx7?
It's on the top of the engine at the front . It looks like a distributor with no leads. Which is kinda what it is. It should have a black plastic/steel cover/plate which is about 6cm across and about 1.5mm wide. They sometimes have billet alloy or steel covers with rotor logos etched into them. There are two maybe three wires which come from it too. It's just to the right and under your alternator. Hope this helps
How much would it cost to replace a crank shaft sensor in a dodge 2006 grand caravan?
Your vehicle is under 50K (or higher in some cases,) it is under factory warranty, So that it in and ask for the work
Where is the crank position sensor on a 1996 Chrysler cirrus 2.5 engine?
under the distributor about 6 inches. You will see this big huge bolt and right next to it a smaller bolt which pertains to the crank sensor. you can follow a set of wiring down to the sensor. The bolt is a 10 MM to the right of the big bolt you find under the distributor. the sensor itself is black in color and the easiest way to take it off it to remove the tire and get a very long extension with a 10 MM socket and get in through the battery side of the car (driver side)
Where is cam position sensor for 1999 Saturn SL2?
CPS is located above the starter on the back side of the engine held in with a 10mm bolts.
Where is the crankshaft sensor on a quad 4 motor?
Did you look above the oil filter mounting boss? The sensor is there on some quad 4 engines according to the Chilton book
Where is the crank sensor on a 1999 Saturn SL1?
It is located on the back side of the block (firewall) almost directly in the center, under the intake manifold. You will need to remove the electrical connector and retaining bolt. Then "lift" it out. Good Luck.
Where is the crankshaft position sensor located on a 2001 Mitsubishi eclipse 3.0?
It's behind the timing belt. Even so you do not need to remove the belt, you will have to remove the pulley and covers. If you want to replace it.
