0
Dodge Colt
The Colt was a subcompact car sold by Dodge from 1970 to 1994. Its first generation model was powered by a 1,597 cc 4-cylinder engine and was available in 5-door wagon, 4-door sedan, 2-door hardtop and 2-door pillar coupe variants.
203 Questions
What does a problem code 21 mean on a 91 dodge colt?
It means the oxygen sensor is not giving an input to the PCM. Either a bad O2 sensor or a wiring issue.
with the engine off, loosen each spark plug wire at the spark plug and then set it back on the plug but not too tight so they can easily be removed later once the engine is running. now attempt to start the engine and once it's running remove each spark plug wire, one at a time with insulated pliers, and then replacing it see if the engine running changes. if you find one or two where there is no chg in the way it runs with the plug wire removed you probably have a bad plug. it's a good idea to change all 4 if they haven't been changed for awhile. however if that doesn't bring success check to see if you may have condensation under the distributor cap. i had a vehicle that was notorious for that every time the humidity got high outside. then i would take WD40, spray it inside the dist. cap and wipe it out twice and it would be fine. one last thing that it could be which will cost the most of these remedies is to chg the plug wires them selves if they are getting older. some seem to last forever while others break down inside much more quickly, and while you're at it you might as well change the dist. cap and rotor. hope that helps.
Scan tool.
Where is the reverse light switch on a manual 1989 Dodge Colt?
this question should be listed under automobile repair
this question best served in the automotive section
Why does the engine rev up and down when the throttle is held steady on a 1989 Dodge Colt?
I had the same problem and it is your oxygen sensor.
How do you remove front brake rotors on a 1989 dodge colt?
this question should be under automible repair
I'm having the same issue and from what I can find out the rotors cannot come off without pressing the entire assembly off the spindle.A 92 Dodge colt started ran died now it wont start and i have no spark why do i have no spark?
If you are getting power to your coil and you still have no spark at the spark plug, you have a bad coil. Beyond that you will have to chase the electrical system. could be a fusible link.
Where is a ignition module located on a 1993 dodge colt?
where is a ignitionmodule in a dodge colt a 1993
Where is the ignition power transistor on a 94 dodge colt?
most likely it will be on the drivers side right up against the fire wall
Dodge colt 1993 no start no fire?
Check the battery to ensure it has sufficient charge. Inspect the spark plugs and ignition system for any issues. Consider testing the starter motor and fuel system components like the fuel pump and fuel filter to identify the root cause of the no start issue.
How do you install a distributor in a 1989 Dodge Colt?
it can only fit in one way, take the cap off and turn the rotor button slowly while you push in on the distrubter.
Where is the fuel pump relay in a dodge colt 94?
In a 1994 Dodge Colt, the fuel pump relay is typically located in the engine compartment fuse box. It may also be found under the dashboard, near the driver's side or behind the glove compartment. To identify the relay, refer to the fuse box cover for a diagram or consult the vehicle's service manual for specific details. Always ensure the vehicle is off and take necessary precautions when working with electrical components.
It's the same for most cars. W/O the tank heater oil is thick so it takes more to turn the engine. When it's fairly cold gas doesn't vaporize as well, so may take more turns to start. Also, tank heater is bound to increase underhood temp and batteries are very sensitive to heat and cold.
At temps lower than freezing, you'll likely save money by plugging in with a timer to kick it off a couple hours before first use. Drive away with 70 degree coolant temps, choke faster to go off, less pollution and soon to get heat out of the heater.
But! all in....... you may well be ready for a new battery.
90 Dodge colt where is the fuel pump located?
In a 1990 Dodge Colt, the fuel pump is typically located inside the fuel tank. To access it, you usually need to remove the tank from the vehicle, as it is not externally accessible. Additionally, there may be an access panel in the trunk area, depending on the specific model. Always refer to the service manual for detailed instructions and safety precautions.
What is the purpose of the transmission?
Transmission is used to send data from one place to the other. It is a means of communication, which uses a transmitter to send out information through a communication channel.
What transmission fluid do you put in a 1994 dodge colt its a standard?
this question should be listed under automobile repair
Where is the ignitor located on the 92 accord?
In the distributor. You have to remove the distributor cap to gain access to it.
Where is the fuel pump relay located on a 1989 Plymouth colt hatchback?
Unfortunately, I can only tell you where the relay is located on a 1990 1.5 Plymouth colt hatchback. Perhaps they are the same.
As far as I know the relay that controls the fuel pump is in something the manual calls a MPI Control Relay (Multi-Point Injection). This relay seems to handle a couple of different things and I believe it is located almost directly behind the ash tray, below the radio, etc. On my car, if you take out the ash trash you can see a small golden can directly behind it, held in with one screw. That's the relay.
that's not the fuel pump relay. that is the fuel injection relay.
num1 loosen big 32mm bolt from the axel take and loosen the wheel jack if ur lucky hoist remove brake caliper bolts 10 mm pull caliper off rotor take rotor off loosen the tie rod ends hit hard with big hammerpop the tie rod off grab wrenches take lower ball joint bolt out pop ball joint out of a arm tap axle out of the nuckle go under the car with the pan pop with a pry bar axle out of transreverse to replace
Drain transmission. Caliper bolts have 12mm heads. You do not have to remove rotor, tie rod ends or ball joint. Simply remove the lower control arm mounting bolts that secure it to the frame and then let the arm slowly lower away. Trust me, some repair manuals print false information. I have done this smoothly 3 times so I know what I am talking about. Install new circlips on inside axle spline. Instal new seals in transmission. John 805-904-9817
How can you remove the torque plate on a 90 Dodge Colt to change the lug bolts?
You pull the cotter pin out of the axle nut remove the nut ,remove the 4 retaining bolts,and pull the flange off with a good heavy made 3 jaw gear puller you will probally nead a breaker bar or impact wrench to do this DO NOT FORGET TO SET THE PARKING BRAKE , CHOCK THE WHEELS , AND HAVE THE CAR ON A JACK STAND,OR SUPPORTED WITH A SOLID WOODEN BLOCK SAY A 1 FOOT SQUARE OR LARGER ( DO NOT USE CONCREETE BLOCKS,BRICKS,STONES,OR THE JACK THAT COMES FACTORY WITH THE CAR I HAVE SEEN PEOPLE GET HURT OR KILLED LIKE THAT, FROM THE CAR FALLING ON THEM).
