0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
How do you reset check engine light on 2003 dodge ram?
There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.
By repairing whatever tripped the light. Then you use an OBD2 scan tool to reset the light. You just have to disconnect the battery for a minute and then the check engine light go off, if the problem has been fixed!!! Disconnecting the battery will reset the light on most, but not all, 1995 & older cars, but on 1996 and newer cars this will rarely reset the light. It requires an OBD2 scan tool to reset the light on most newer cars.
There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.
The input and output speed sensors are located on the front of the trans. They have two wires and the input sensor is closer to the engine.
How do you bypass the transponder on a Dodge Durango 2000 with a 5.2 liter V8 Magnum?
The sentry key immobilizer system can not be bypassed on a Dodge. It needs repaired is malfunctioning.
How do you adjust the flywheel on a 2004 Dodge?
There is not an adjustment on a flywheel. Your problem will most likely be the starter.
Where would you find the thermostat on a 1998 Dodge Ram 1500 V8 quad cab?
underneath the alternator on most Dodge V8 engines underneath the alternator on most Dodge V8 engines
Where is the crank sensor located on a 1999 Saturn SL2 and how do you change it?
The crank sensor is behind the starter. Remover the starter at the back of the engine and you will see the sensor
Does 2002 dodge 1500 have circuit board in the taillight?
yes the taillight does in fact have a cicuit board. Once you take off the two bolts to remove the entire fixture the circuit board is the long plastic piece with the 4 screws holding in your 3 light bulbs
It has two oxygen sensors. One at the front of the catalytic converter and one after it.
Where is the camshaft sensor in a 1998 dodge ram 2500 5.9L gas engine?
Under the rotor inside the distributor cap
Under the rotor inside the distributor cap
How much horsepower does a 2003 5.7 hemi have with a cold air intake?
The cold air intake may add 5-10 hp to the 335 it was built with.
ABS and brake lights on dash will be on. Speedometer and cruise will be inoperative.
ABS and brake lights on dash will be on. Speedometer and cruise will be inoperative.
1982 Dodge D150 dies when battery cable is removedwhy?
Your charging system is not working. It could be the Alternator or the regulator or both. It's not a good idea to test the charging system by removing a battery cable while engine is running, this can damage the charging system.
How do you install a power steering pump in a 1999 Dodge Durango?
Replacing your power steering pump is a relatively easy task with the correct tools. Those being the pulley removal and installation tools, often sold in a kit. You will also need a pair of pliers, and open end wrenches. First remove the drive belt. Place a drain pan under the pump to catch the power steering fluid. Detach the two hoses on the back of the unit, which are the pressure and return lines. Remove top bracket nut which secures the battery ground cable. Then proceed to remove the bracket mounting bolts. Typically a replacement pump will be sold without the pulley. Hence the necessity of the pulley installation and removal tools. You can also save a little by re-using the old reservoir. The installation is just the reverse of the removal. Be sure to replace any o-rings. After mounting the new pump and re-installing the drive belt, fill the reservoir with power steering fluid and bleed the system to remove any air by jacking up the front of the vehicle, start the engine and allow it to run at fast idle, if necessary add more fluid to bring the level of fluid to the cold mark on the dipstick. Begin bleeding the system by turning the wheels side to side without hitting the stops. Keep the reservoir full of fluid as this is done. when all of the air is worked out of the system return wheels to the straight ahead position and allow to run for several minutes more. Road test to insure proper operation of your steering components. Recheck fluid level to be sure it reaches the hot mark when the engine is at normal operating temperature.
How would you replace a belt tensioner on a 91 Corsica 2.2 l with aftermarket AC?
The belt tensioner on a 91 Corsica 2.2L with an aftermarket AC is replaced by loosening the retaining bolt and pushing the tensioner to the side. The belt can then be taken off, the tensioner removed, and a new one bolted into position.
How do you get ABS trouble codes and where is the ABS computer located in the Van?
Check out www.autozone.com. They have some repair information for some of the model years of the Windstar. This may help you to find the location of the ABS parts you are looking for. I do not know how to get the codes but I'm sure it must be a special code reader.
I can't help with the codes, but the actual ABS controller is under the driver's seat. It "talks" to the rest of the computer controls via the data lines that run all through the vehicle. My schematics show it connected by way of a 25-pin connector.
See "Related Questions" below for more
How do you change the temperature sensor on a 2002 2.3 Ranger?
According to Haynes Manual, 2001 and later 2.3L Ford Ranger, the Cylinder Head Temperature (CHT) sensor replaces the Engine Coolant Temperature (ECT) sensor on earlier models. The CHT sensor is located between the #2 and #3 spark plugs in the cylinder head and can be accessed through the valve cover. Carefully pull back the CHT cover to expose the electrical connector then disconnect it from the CHT sensor. Unscrew the CHT sensor and remove it. Installation is the reverse of removal, being careful not to overtighten the CHT sensor when installing it.
first get rid of that quadrojunk carb and spend a few more dollars on something worth installing and then reask this question
Answers such as above are not helpful. Quadrajet carbs work excellently delivering fuel economy and performance. This person wanted help with the vacuum lines, not a flippant reply that showed your bias and lack of knowledge. If the original poster still needs help, he or she should find a good manual or pay Alldata for a schematic.
Instructions on how to remove ignition switch on a 1990 Lexus LS400?
Remove the retaining ring from the top of your 1990 Lexus ignition switch. The ignition switch will slide out. Remove the wiring harness.
What size wipers fit 2009-2010 dodge ram 1500 crew cab?
The 2009-2010 Dodge Ram Series 1500 Pickups take 22" replacement windshield wiper blades on both sides front. Note however, when buying wipers be sure to always lookup your vehicle make, model and year in the application guide book at the store, or now-a-days you can Google 'lookup wiper size'.
it just means that the head on the motor is hemispherical. That means it has a curve to it.
Which wire is a remote amp turn on wire on a 2012 dodge ram 1500?
The remote amp turn on a 2012 Dodge Ram 1500 is the wire that taps on the harness to supply the 12v.
