0
Ford Bronco II
The Ford Bronco II, a smaller version of Ford Bronco, is a compact SUV produced from 1984 to 1990. The Bronco II offers optional 4WD, mechanically identical to Ford Ranger, but does not have a removable roof.
1,174 Questions
How do you change a heater core for a 2001?
everyone should have a manual for their vehicle, and the library should have a professional manual available...in the reference section, you'll have to make copies of the important sections...good luck :)
maf sensor
Your 1984 Bronco II just quit.You replaced coil and distributar and module and it still wont start.?
are you sure your not getting spark, if your not i had the same problem and i chased it to the plug on the coil, it looked good but when i pulled the wires i found them bad. make sure its a spark problem, i also had a fuel issue but my fuel pump was working fine, turned out to be a bad return regulator on the fuel rail.
How do you get the harmonic balancer off a 96 Toyota tacoma?
take off the fan shroud and there is one bolt holding the balancer on, its easy.
What was the transafrica forum membership size in 1984 to 1986?
The TransAfrica Forum, founded in 1980, grew significantly in membership during the mid-1980s. By 1984 to 1986, its membership was estimated to be around 12,000 individuals. This organization aimed to promote solidarity with African nations and advocate for U.S. policies that supported African self-determination and development. The increase in membership reflected growing interest in African issues and activism within the United States during that period.
How do you install AC compressor on a 1989 Bronco II?
1. Discharge the a/c system....
2. Remove the drive belt...
3. Remove the a/c clutch wire pigtail...
4. Remove the a/c hose assembly..
5. Remove the front and rear bolts...
6. Remove the compressor...
7. Reverse to install...
8. Evacuate and recharge...
9. Add the correct amount of freon and oil......
Where is the fuel cut off switch located on a 1988 Ford Bronco II?
Check the passenger side foot well, upper left corner area under the carpet.
Replace ford bronco lock motor?
first what made the motor lock up, and what kind of motor is it , it could be alot of things like no oil, the trans, if its fuel injection and you put gas in the intake to try and start it this would lock it down as well. try pulling the spark plugs and turning over the motor.
How to put gear oil in manual trannsmission?
Plug on the upper side of the transmission. Use only the proper lube as outlined in your owner's manual.
Need a wiring diagram for the Bronco II?
Wireing diagram of what component? I apologize, I need the diagram for the firing order for the distributor. My husband said he needs the diagram coming off the block?
AnswerI am unsure of that. My father in law is looking for it. I would assume for the electrical components.they sell a maunal at any auto part store with the the digram in it and what year is your bronco 2
Why would the steering apparatus creak or crackle when you turn the wheel on a 1997 Dodge Ram?
I corrected the problem on my 1998 Dodge Ram 1500 by replacing the upper and lower ball joints.
What is 1986 Bronco II 2.9L V6 lifter gap?
The 86 2.9L has hydraulic lifters (no gap). To adjust, make sure lifter is on base of cam (not raised). Loosen rocker arm until push rod is slightly loose, tighten rocker slowly until it takes just a little pressure (not much) to turn rod by fingers. The tighten 1 1/2 more turns. This centers lifter piston. I've found the best way is one cylinder at a time, this requires turning the motor by hand several times but it's worth it.
Where can you find the oil pressure sensor on a 1990 Ford Bronco II 2.9L V6?
Front left side of the engine below the cylinder head in the engine block.
How do you change the heater core in a 1992 ford explorer V6 4.0L?
Open and empty the glove compartment , press in on both sides of the glove compartment at the top and pivot it down , remove the 2 hinge screws and the glove compartment.
on the heater housing , remove the 4 screws on the bottom , then slide down the bottom of the housing , there is the core, the only thing holding it in now are the heater hoses.
loosen the hose clamps and remove the hoses , then reverse the process to install the new core, it shouldn't take more than 90 minutes.
86 bronco ii 2.9efi runs 20 minutes then dies wait 20-30 minuts then starts and runs again?
possible bad ignition mod or pick ups both connect to distr check fourms on tfi mod bronco 2
We both know it floats
How difficult is it to replace a starter On a 91 Sunbird?
If it is a 4 cylinder then you need to approach it from the rear of engine and from underneath as it is located just below the intake manifold. It is diffcult t oreach and if you are unexperinced you in for a hell of a time.I just paud to have it done as it really is best to do off a car hoist.It is also in the center of the engine making it even harder without a hoist.
Answeryep took me three days of cussing and curseing, but i finally got it :)