0
Ford Bronco
Manufactured from 1966-1996, the Ford Bronco is a two-door sport utility vehicle produced in five generations. Broncos are divided into two categories, which are the early Broncos and the full-size Broncos, and were later replaced by the larger Ford Expedition.
1,597 Questions
Did you try putting gear shift in "neutral" when shifting into 4 WD Low?
Where is the hazzard flasher located on a 95 ford bronco full size?
in the fuse box on the drivers side just under the steering wheel (between the door an steering wheel) it's the big round silver one.
What are the steps involved in changing the freeze plugs on a 1999 Mercury Sable with a 3.0 engine?
No need to change what you call freeze plugs, (they are actually casting plugs), unless they are leaking. To replace on simply drain the radiator to below the level of the plug. Drive a chisel into the middle of the plug. Pry sideways to remove it. Clean the area throughly. Install the new plug, by inserting it and hitting it dead center with a plastic or brass hammer.
Why wont a 89 Ford Bronco w auto not move when put in gear Fluid is full and trans pump is working?
Internal clutch pack might be worn. There might be a problem with the auto-trans "valve body", the filter might be plugged, but if that's the case the trans is through anyway. The torque converter is bad or the intire trans is bad
What could cause a 1994 351 to run rough and smell of unburned fuel?
well i'd give it a tune up new plugs new cap and rotor new plug wires and have timing checked Fuel pressure regulators can also go bad, or your EFI poppets are clogged and you're not getting a full "spray" from them.
How do you tighten the loose steering on a 93 Jeep Cherokee with a lot of play in it?
check the intermediate steering shaft. these have a key in them to keep them from failing completely. you can weld the d-tab to the u-joint. the steels are compatible
Generally vacuum lines are sold in bulk hose at any auto parts store. IF there are special ends, the parts store (assuming the countermaan is on the ball), should help you to make some. Auto parts store. napa, Autozone, etc...
How much does it cost to fix a ford broncos steering column?
I just found one on Ebay for $160.00 + 25.00 fro shipping. I did the work myself & took about 1 1/2 hrs to complete it being my 1st time.
What would cause a 1990 ford bronco to just not start again?
Have the neutral safety switch checked. Pop the hood, hold a key across the screw posts on the solinoid. it should start......make sure ignition is on and truck in Neutral.
How do you adjust transmission linkage on full size 1987 ford bronco?
look under the driver side right beside the transmission there is a slide with a bolt and nut loosen them and have someone put the lever in place then tighten
Where is PCV valve located on 1987 Ford bronco?
The pcv is located on the passenger side of the motor, under the edge of the intake manifold, in the back.
timing cover, it bolts to the block and covers the timing chain and gears, then the water pump bolts to it.
How do you install a Starter on a 1983 Honda 1100 Goldwing?
remove battery cable remove gear change lever remove two bolts thru starter then work it out .' that's it
Where is the ecu on o a ford bronco II?
its on the left side of the brake and gas peddling and/or clutch.you may need to remove a piece of the doors lineing panel to acces it.to remove it you must loosen the bolt in the electrical plug which should use a 10mm socket and the bracket which uses (in some cases)an 11/32 socket. after this the ECU shoulbe free to remove
What is the 1980 ford bronco curb weight?
With a 351w, c6 auto trans, 33" tires(they'd only add 10-15 lbs over the stock 31s), no gas, and no rear or passenger seats, my 82 (which aside from I believe the grill and tailgate is identical to an 80) weighed in at 3892 lbs
How do you install a starter for a 1992 Chevy Lumina v6 3.1?
You'll need to lift up the car and support it on at least one jack stand. Disconnect the positive terminal of the battery. Remove the oil filter (make sure a drain pan is underneath). There are two bolts that hold the starter to the engine/transmission. (15mm I think) These bolts are vertical; it helps to have a wobble-extension to get them out. After it's loose, disconnect the positive battery lead and the ignition signal lead from the solenoid. (there is another nut on there grounding the solenoid to the starter - don't mess with it; you'll be removing them together). After your two nuts have been removed and the wires moved away, slide the starter over and out around the a/c lines through the space where the oil filter used to be. Mine had a shim on the top of the starter, but the aftermarket starter from the parts store was made to be used without it. Make sure you know whether or not your new starter needs the shim.
Additional infoIt is generally easier to remove the starter if you disconnect the electrical connections [battery lead and ignition lead(s)] before taking out the starter bolts. This prevents the weight of the starter from pulling out the wiring and also makes it easier to move around in such a tight space.How do you check power steering fluid on a 1987 ford bronco?
Remove the cap and check the level when the fluid is hot.
What weight motor oil does a 1992 Ford F-150 5.8 V8 need?
I just inherited my grandfathers 1992 Ford F-150 5.8L V8 and the sticker on the window says "10-50".
Answer It should use 10w30 motor oil.
you should use what it tells you to use
How do you remove the ignition switch key lock on a 1988 Jeep Cherokee?
Remove steering wheel, turn signal (4 screws), and torx holding ignition, reverse to reinstall.
What was the Ford car in casino royal?
The car that James Bond drives after arriving in the Bahamas is an MK4 Ford Mondeo.
What transmission came in 1988 full size ford bronco with a 351 w motor?
I believe that is a version of the C6 - 3 speed automatic transmission
