0
Ford Ranger XL
The Ranger XL is a pick-up truck manufactured by the American automaker Ford Motor Company. Some of the notable features found in the 2010 model are Electronic Stability Control, and torso and head airbags in the front seat.
4,911 Questions
How do you change the headlight bulbs in a 2004 Impala LS?
pop the hood, there are two white "locking plates" on both ends of each headlight housing. the two inner ones on each are under a plastic panel. If your hands are smaal enough you can reach them. the outer clips are clearly visible. just pull up on them until they pop up.
Do you have to take the transmission or motor out to put a crank senor in a 2.0 Chevy tracker?
i have a 2001 Chevy tracker and i just replaced the crank sensor. i have been having a problem with mine not cranking. i would drive it and cut it off. it would not crank up until after it sat for a while. the crank sensor has not fixed the problem though. you have to take the tranmission out and take the flywheel off. the sensor is behind it. hopes this helps. i got a sensor at napa for about $100. advance auto parts wanted about $174 for it i think
How do you Change the headlight bulb on a Mitsubishi gto?
the answer is at
http://gtouser.wordpress.com/2008/12/21/how-to-change-the-headlight-bulbs-on-a-mitsubishi-gto-or-3000gt/
so just paste this link in your web browser and you can find out.
hi
Where is the diagnostic test point on a 2000 ford ranger?
The Data Link Connector ( DLC ) is behind a small removable plastic panel , in your
dash , below your steering wheel and between the inside hood release and your
parking brake release
How much is a 1986 Ford Ranger worth?
It will be an antique in 3 years and if it's in good shape, it will increase in value. Low mileage, extra options add to the value. If roadworthy with normal wear, no extras; a dealer will ask about $1000.
A drag link converts rotary motion from a crank to a second crank or link in a different plane or axis.
The term is commonly used in automotive technology for the link in a four bar steering linkage that converts rotation of a steering arm to a center link and eventually to tie rod links which pivot the wheels to be steered. A drag link is used when the steering arm operates in a plane above the other links. The drag link converts the sweeping arc of the steering arm to linear motion in the plane of the other steering links.
An alternate steering mechanism is a rack and pinion, a three bar linkage that eliminates the drag link by directly moving the center link.
The length of a drag link can affect the geometry and thus the steering ratio. Severe wear of this part can affect the wheel alignment such as Toe-in or Toe-out settings. This can drastically affect the handling and stability of the vehicle at speed.
I have the same problem with my 1994 F150 except it will shift down
from overdrive...let me know if you get an answer..dcfrisbie@gmail.com I have a 1994 ford F150 which was doing the same thing...ended up being the throttle position sensor...Drives like a new truck after new one was installed....
Only way is to run your hands along to find bolts, and work in small area. be sure to have plenty of lock free, as it's best to let it soak for about 15 minutes, and will help when prying off the bell housing. -------------------------------------------------------------------------- Answer; Actually there is another way. I personally remove my share of motor and transmissions in my time... I used a 3-foot extension from the bottom of the vehicle with the correct socket and ratchet you should be able to remove all the bell-housing bolts. With the proper floor clearance of course...
Why does the starter make a loud spinning noise and not crank over the engine?
If it happens intermittently, it is caused by a broken tooth or teeth on the engine ring gear. Thus when the starter solenoid throws the pinion gear backwards, the pinion and ring gear will not engage. In some rare cases the pinion gear can come off or the solenoid itself fails, yeilding the same result. You can test this by putting the car into gear and moving it slightly to move the ring gear (in some cars). Sometimes opening the drivers door and jumping up and down on the door sill can rock the engine enough to move the ring (again in some cars). The car might start. The only fix for this ultimately is to replace the ring gear.
What is the horsepower for the 1987 Nissan d21 pickup. With a 2.4 liter z 24 8 spark plug engine?
103 hp.
Why does Black smoke always come out the exhaust of my 1987 ford ranger?
because its a terrible car mad , if the smoke is black the car wants to die , take it out of its miysery
Where is the thermostat on a 93 Ford Ranger?
If you follow the top radiator hose torwards the motor,it will be hooked to the thermostat houseing.Remove the two bolts and the houseing and there it is.
How do you test injectors Ford Ranger?
Haynes or Chilton book is a must before you start diagnostics.
2nd you will need an OHM meter.
Depending on what ranger you have, I know the 4.0L is 11-18OHMS.
a good idea would be to test ALL injectors, write down ALL OHM #'s you obtain. compare them all. And from there you will know where the problem injector is. If all injectors have no power, look at your ECM "electronic control module.
I hope this helped you a lil bit
Where is the BARO sensor located on a 1991 Ford Ranger?
I don't know if it is the same as the Ford Mustang , but the BAP sensor was mounted on the firewall - good luck
What is the little black and yellow circle you see at the crash tests?
They make different points on the car easy to identify in the video of the test. By measuring the points in different frames of the videos, they can show how much different parts of the car deformed.
97 catera that won't start you thought it was the fuel pump but that is good any ideas?
Check your crank shaft sensor. Had the same problem, replaced crank shaft sensor and fixed the problem.
Where does 'don't get your dobber down' come from?
It comes from an old painters tool called a dauber. When painters would get sad and stopped painting it was said that they "had their dauber down"
Where is the thermostat located on a 2003 GMC Savana 2500 6.0L engine?
Inside the thermostat housing...the housing is bolted directly to the water pump on the lower left side with 2 hex bolts(10mm). The outlet of the therm housing connects to the lower rad hose. You should the able to remove the top hex bolt simply by reaching over the fan shroud and down behind the serpentine belt. The lower bolt is easier to remove from underneath the van.
Is the 1992 colt 1.5 is it interference engine?
Yes , the 1.5 liter 4 cylinder engine in a 1992 Dodge Colt is an interference engine
according to the Gates website ( they make timing belts etc. )
Have a 1993 ford ranger 4x4 manual trans and just quit cant shift to any gear?
When You Push The Clutch In Make Sure Its To The Floor
