0
Air Filters and Intake Manifolds
Air filters are devices that remove solid particles such as dust, mold, and bacteria from the air. Used in building ventilation systems and engines, they contain an intake manifold that is primarily tasked to optimize the system/engine’s performance and efficiency.
2,054 Questions
How do you install an air filter on a 2003 Navigator?
1. Remove the flat plastic cover from the top of the engine by removing the two bolts and pulling up. There is a hidden friction support on the left side of the enginge when viewed from the front. 2. Loosen the hose clamp around the air intake at the engine. 3. Loosed the hose clamp at the outlet of the air filter assembly. 4. Remove the hose assembly that connects the air filter assembly to the engine air intake. 5. Undo the spring clamp that hold the two halves of the air filter assembly together and loosen the clamp ring. IMPORTANT: Note where the clamp lever is in relation to the line up tab at the top of the filter housing. 6. Pull the front of the air assembly away from the rest of the filter housing. Note where the clamp ring fits over the plastic tabs at the bottom of the removed housing half. IMPORTANT: Becareful when removing the front of the housing as there is a wiring harness that is connected to an air mass sensor in the housing. I did not need to disconnect the wiring harness as I was able to move the loose part toward the firewall. 7. You are now able to access the filter to replace it. 8. Reverse these disassembly steps to everything back together properly.
What is code P0300 for 2006 Honda Pilot?
P0300 Diagnostic Code - Random Misfire
Symptoms.
Engine may stumble or miss
Engine may be hard to start
you may notice no issues
Cause
Failing spark plugs or spark plug wires
Bad coil or coil pack
Failing oxygen sensor(s)
Bad fuel injector or more than one
Stuck exhaust valve
Bad catalytic converter
EGR valve or valve passage clogging
Bad camshaft position sensor
Bad PCM or ECM
The Fix
Best first action is a tune up, new plugs, wires, inspect all hoses and wire connections then reset the code. If it returns you will need to narrow it down to a system, coils and coil packs should be tested, catalytic converters for function ( do you smell rotten eggs?). A misfire that jumps cylinders could indicate a lean condition, do you have any other codes along with the 300? this will help clue you in to the source, check valve function to make sure they are opening and closing fully.
This is probably pone of the most difficult codes to troubleshoot, so start with the basics and work your way into the more expensive options, in many cases a good old tune up solves the problem, back it up with a fuel system cleaning and see where you stand.
P0300 : multiple cylinder misfire.
Where is the air filter on a K1200 LT?
The air filter is under the fuel tank on the K1200LT, you will only change these during full services, the air filter recommended change is listed at every 12,000 miles but it will not need it that soon unless you live down a dusty dirt road. This is a decent size job since the tupperware on both sides and stingray must be removed to get at the fuel tank.
What is the use of air filters?
The use of air filters is to clean the environment or the air. The air filters are effective in getting rid of material such as dust, bacteria or pollen form the air.
Who makes a device to remove ozone from room air?
Any air moving device that has either Carulite 200 (a catalyst that turns ozone back to oxygen) or activated carbon (which requires frequent replacement / reactivation), will reduce ozone levels in the air passing through it. Odorous compounds with double carbon bonds or not-fully-oxidized sulfur will consume ozone. These would be perfumes, flatulence (sorry), rotten egg smells, and so on.
Start in the center and work your way around in a circular pattern. Torque in 3 stages with the first stage just to feel them touch, then to about 20 ft./lbs, then to about 40 ft./lbs on the final step. Almost any repair manual would have the exact pattern recommended by the manufacturer.
Can you bypass the intake manifold and use both ports on the water pump instead?
Not sure what your trying to do but the year, make, model and engine info would help.
How do you replace the cabin air filter on a 2002 Toyota Sienna?
A previous poster asked if there even WAS a cabin air filter and was told 'no'.
I changed the cabin air filter on my Prius. It was very simple. Just open the lower glove box, squeeze the sides slightly and you can see the filter frame on the firewall. It slides out and you remove it and replace with the new pad. It is about 10" by 10".
After spending 30 minutes on the Internet looking for a replacement cabin air filter for my 2001 Toyota Sienna the parts department told me the van does not have one. No wonder I have had trouble locating it! DUH
Intake manifold gasket 93 ford ranger 4.0 5 speed leaking at the head is this a gasket or worse?
Should just be the gasket but check the upper side of the cylinder head while you have it apart to see if it has problems. Intake gasket leaks will present vacuum problems, if pressure is pushing air out of the affected area then it may be the head.
It is located behind the glove box. Remove the glove box completely and it is attached with two screws. Hope this helps
Where is cabin filter on 2006 Kia serento?
i just got a kia SEDONA and it is behind the glove box--i am trying to release the stoppers on the glove box without breaking them.MAYBE your's is in the same place.
Does a 1997 ford f-150 have a cabin air filter?
I believe it was an option in 1997. If you have one it would be located under the dash behind the glove-box. Typically if it's equipped it will have something in the owners manual mentioning the replacement intervals and service instructions.
Where is the blower resistor on a 2000 Oldsmobile Intrigue?
I have Olds Intrigue 2000. Blower control resistor (Controller) located behind the
blower motor. Very close to the firewall.
Using 5.5 mm. socket remove the blower first. (3 screws are holding the blower)
Using the same socket (5.5 mm) remove one visible screw which holds the resistor.
You will have to loosen two other screws, located between the resistor and firewall. You don't need to remove them completely, just loosen them! And it is a pain in the neck to get there!!!
Resistor slides out when rear screws are loose.
--------------------------------------------------------------------------------------------------------
right side just above the carpet under the glove box.
I am not sure about the 2000, but the 1998 model was an easy fix. Simply remove the carpeted upholstery with an upholstery button removal tool (don't forget to remove the interior light from it). Then, using a 7/32" deep-well socket, remove the blower motor (3 screws total). Be sure to support the fan while removing the motor since the screws break easily. Next, remove the bracket that has a wire tie on it which ties the cable for the blower motor and remove the wire tie (it slides apart left/right, btw). Carefully disconnect the blower motor from the blower motor resistor. Disconnect the remaining wire harness from the blower motor resistor. Using the same 7/32" deep-well socket, remove the screw closest to you and LOOSEN the back 2 screws. You will need to press the socket up to each screw since the rubber on the firewall is extremely close to the blower motor resistor. Once the resistor has been removed, simply slide the new on into place and install the screw closest to you. Now tighten up the back 2 screws. One of the screws is at a rather wicked angle so keep trying. Now replace all of the parts that you removed and you are done.
While you are at it, the fan control switch was extremely corroded in our car. The switch can be removed by pulling out the center console (2 9/32" screws on top of the arm rest). The switch comes apart by working each of the plastic tabs until it comes apart. Use some emery paper to clean up the contact surface.
----------------------------------------------------------------------------------------------------------
I also replaced the resistor on my 2000 Intrigue. I used 7/32 deep-well socket I bought from Sears and a flex-cable ratchet. The front screw was easy to remove, but the rear screws seemed to be impossible to reach with the firewall rubber covering the screw area. I then pressed the firewall rubber with screw driver and the rubber stayed pressed. And the bottom screw became visible making it easy to loosen. With the rubber pressed away I could stick in my finger and could feel the top screw. With several attempts I could loosen the top screw and the resistor came out. When I replaced a new resistor I rotated the rear screws so that the resistor just slides in, and tightened the front screw. I left the rear screws untightened just in case I replace it again.
I was able to replace the resistor without removing the blower motor and even though less safe I made it without removing the negative cable from the battery.
What is the labor time to replace intake manifold gasket on a 2001 intake manifold gasket?
around 6-7 hours according to AllData
Where does the air go from the filter?
After the air filter, the air goes into the cylinder as a mixture with the fuel to be burned.
Head bolt torque 1992 continental 3.8 v6?
Head Bolts:
1. 15ft lbs
2. 30ft lbs
3. 37ft lbs
4. loosen 1 bolt 2-3 turns then do final torque before going to next bolt.
Final torque:
Long bolt 30-37lbs +180 degree's (1/2 turm tighter)
Short bolt 15-22lbs +180 degree's (1/2 turm tighter)
Yes, it seems odd to loosen a bolt once it's tight but it is what ford recommends. Tighten all bolts to 1st torque setting then 2nd and then 3rd. Once all bolts are tightened to 37 ft lbs you must then loosen 1 bolt 2 to 3 turns and re-torque (29-37 long bolt or 15-22 short bolt). Once torque setting is reached you then tighten the bolt 1/2 turn more. Do this for each bolt. Loosening and re-torque only 1 bolt at a time.
I have seen the Ford service bulletin that confirm these settings.
What intake manifold use for automatic trans?
The manifold needs to be the correct one for the engine.
Either the manufacturers part or an aftermarket part.
Manifolds for automatic transmissioned cars normally have an extra drilling in them for vacuum lines
What is the torque on intake of 1997 34?
torque specs are lower intake 115in-ibs upper intake 18ft-lbs
What does it mean if you have oil in your air filter?
Check the PCV (Positive Crankcase Ventilation) valve. Failure in the pcv ? Usually it's piston ring blow by caused by worn piston rings. Get a compression check. I'll bet this has at least 100K miles on it. Its called "blow-by" you need to replace the piston rings. Over time the rings and cylinders get wore out allowing oil to go past the oil compression ring. Also check to see if there are bubbles on the dipstick to your oil,thats an indication of bad rings too, its gas in your oil. Check if your PCV (Positive Crankcase Ventilation) valve is ok
What is the cost to replace intake manifold gasket on 1996 Buick century?
I just had the intake manifold gasket replaced on my 96 century yesterday and my bill was $450 but my gasket was only leaking out. If its leaking into your oil it may be more.
Where is the air filter on a Kia Rio?
What year and engine? Also engine air filter or cabin air filter?
answer
Open the hood of the Rio and locate the air filter's casing, which you'll see near the center-top of the engine. The air filter casing is a large, black plastic case.
Open the plastic housing case by using a flat head screwdriver to unhook each clip around the perimeter of the case. Once all the clips are unhooked, the case should open easily and reveal the air filter.
How do you replace the air filter on an 88 CRX si?
As u r facing the car w/hood open the air filter housing is on ur left side. Usually a big black square looking box. There are four clips that hold the top part to the housing. Just pull the clips away in a dwn ward motion. Lift the cover and change the filter out. Once that is done just do the reverse to complete air filter replacement.
