answersLogoWhite

0

Buick

This category covers questions about Buick, officially known as Buick Motor Division. Buick is a subsidiary of General Motors and sells entry-level luxury automobiles.

1,249 Questions

Chevy air conditioning schematic?

05 silverado fan works but no air from vents. This is an easy fix most likely. I would take it to your local Chevy dealership or auto repair shop.

Buick Aurora gets how much miles per gallon?

On your dashboard, wher your date and engibe information is, push the econ button and that will give you your MPG. I have a 1998 Old Aurora and get about 20 in the city and 29 on the highway.

How do you replace the front turn signal bulb located on a 2001 Buick?

I just figured this out after much frustration. There are two vertical white plastic strips behind the main headlight fixture. You have to pull upwards firmly on these--they lock the headlight in place. Once you slide them up you can pull the entire headlight out through the front (carefully, as it's still wired in) and access the turn signal lamp. Pull off the round rubber cover, pull out the socket, and replace the lamp. Then all you have to do is push the socket back into the main housing, put the headlight back in place and slide the plastic tabs back to lock it in.

The car I worked on had a short bolt close to the fender and a long bolt next to the radiator at the back of the headlight assembly. But this is thee way to do it. Thanks alotttt for the info!!!!!

1998 buick century low coolant light on goes on and off but temp gauge stays the same?

I would check the level of coolant in the tank with the radiator cap. The level might be low enough to trigger the light but still provide enough to cool the engine. Just remember to do it when the motor is COOL/COLD. This tank IS pressurized and you will be taking a bath in hot coolant if you don't. It is also possible that the sensor is goin bad, in which case just make sure the level is up to where it need to be.

How do you replace bulbs on high mount stop light on 2001 buick?

There are no bulbs, it is a panel of mini-lights. You access this from the trunk area.

Why do day time running lights stay on when car is not running?

usually due to a defective daytime running light module failure..

How do you replace the alternator on a 1995 Buick V6?

Remove the negative battery cable then use a wrench to take the tension off of the belt and make sure there is a schematic on the fan shroud for the routing of the belt. If not draw one before removing it. Then take the wires off of the rear of the alt then the bolts and work it out.

How much horsepower does a 5.7 350 have?

Depends on the year, vehicle it is installed in, and what 350 you are referring to. GM built many different variations of this engine over the years.

When did Buick stop making electra 225?

Officially, in 1990. 1991 renamed the car Park Avenue with a new body style.

Each time I start my '05 Buick Lacrosse CXL there's this shake what causes this?

If there is a bad shaking after starting a 2005 Buick Lacrosse CXL, it could mean that a motor mount is broken in the engine compartment. The motor needs to be bolted down to the frame or it will vibrate out of its cradle in the engine compartment.

What is the correct firing order for a 1968 Buick 350?

Firing order is the standard 1-8-4-3-6-5-7-2 for the Buick 350 and the distributor rotates in a clockwise direction.

What ground clearance does the 2012 Buick Enclave have?

The ground clearance of the 2012 Buick Enclave is 0 ft. 8.4 in. (8.4 in.).

Is the throttle position sensor and crank position sensor the same thing?

No, the throttle position sensor detects how far open the intake is. The crank position sensor watches the rotation of the crankshaft.

How do you repair the instrument lights on a Buick?

Make sure parking/tail lights are working - if not, may be a fuse If parking/tail are working - may be bulbs or switch

How do you install the pickup in a 1990 ford distributor?

Typical:

Remove distributor.

Use punch to tap roll pin from gear at base of distributor.

Use an arbor press (not a hammer) to press distributor mainshaft out of gear. Shaft will then easily come free of the distributor. If a hammer is used, now replace the complete distributor.

Unbolt the pickup and replace.

Reinstall shaft and gear being sure that gear hole aligns with shaft hole.

Install a new roll pin.

Install in vehicle.

Set ignition timing.