0
Chevy Colorado
Includes information and repair questions about Chevrolet Colorado model cars
1,058 Questions
How do you disable the auto door lock on a 2005 Colorado?
Most programmable features on modern vehicles are changed through a simple button dance, this is no exception.
The procedure may vary depending on the model year.
Automatic Door Locks
With the vehicles engine off, and the ignition in the Lock position, press and hold the power door lock button for approximately three seconds until the DIC displays the current door lock mode. Then press and hold the reset stem for approximately two seconds to switch modes. The following are the mode choices:
Lock 1 (default)
Lock all doors when the vehicle is shifted out of PARK(P) with an automatic transmission, or when the vehicle speed is greater than 15 MPH (24 hm/h) with a manual transmission. Doors will unlock when the vehicle is shifted into PARK(P) with an automatic transmission, or when the ignition key is removed on a manual transmission.
Lock 2
Turns off the automatic door locks
Lock 3
Lock all doors when the vehicle is shifted out of PARK(P) with an automatic transmission, or when the speed is greater than 15 MPH(24km/hr) with a manual transmission. Drivers door will unlock when the vehicle is shifted into PARK(P) with an automatic transmission, or when the ignition key is removed on a manual transmission.
Lock 4
Lock all doors when the vehicle is shifted out of PARK(P) with an automatic transmission, or when the vehicle speed is greater than 15 MPH (24 km/hr) with a manual transmission. No doors will unlock
How do you replace headlamp bulb on 2006 Chevy Colorado?
Instructions to change a drivers side low beam headlight bulb on a Chevy Colorado or a GMC Canyon :
This is for the DRIVERS SIDE LOWBEAM. Other bulbs accessible from back. Check your truck. My trucks Drivers side lowbeam bulb is not accessible with out removing head light, your truck may vary.
Make sure you have plenty of time , if you rush you will have problems so go slow and do it right the first time.
> disconnect the parking light connections on the top of the parking lights .
> carefully remove the grill by sliding the four plastic tabs on the top of grill while gently pulling , then just pull the grill off being careful not to pull to hard . there are two snap connectors behind the parking lamps and three more along the bottom of the grill.
> with a socket remove the two 10mm bolts that secure the headlights. slide the headlights forward .
> this will give you enough room to change the bulb. I removed the connection first. I also put a clean sock on one hand to help handle the bulb without touching the new bulb.
> line up the bulb prongs and rotate clockwise until you feel it snap. inspect the new bulb to insure it is properly installed and all three prongs on the bulb are now hidden. double check through the lens.
>when reinstalling the headlight take a good look first to notice the two tabs on the bottom of the light . the tabs go in first then hold the light up and tight while you reinstall the two 10mm bolts. double check this to make sure both tabs are in . do not over tighten the bolts.
> use a flashlight to help align the grill push connectors. snap in the bottom of the grill first then behind the parking lights then finally snap the four connectors along the top of the grill.
> that's it ! take your time and you will have no problem.
take care, Black GMC Canyon Reg cab Z71
The starter is usually located on the passenger of the vehicle, under and to the rear of the engine where it bolts to the flywheel housing. Steps for changing a starter: (1) disconnect the negative cable at the battery; (2) raise the vehicle and put jackstands under it for support (3) block the rear tires to keep vehicle from rolling backwards; (4) under the vehicle, disconnect the red cable and the black wire that connect to the starter solenoid; (5) unbolt and remove the two bolts that attach the starter to the flywheel housing; (6) pull starter out. Installation is reverse. Good luck...
How do you change the starter in a 72 Chevy c 10?
Disconnect battery. remove to bolts holding starter, may have to remove tranny dust shield for room to move starter around to get it out will be wires on syl remove them if shims are used dont replace unless starter makes noise after replaced
How do you remove the window regulator on a 2004 Chevy Colorado?
You have to pull the door panel off - it is a pretty easy job to replace the regulator and you can buy them cheap online
How to change speakers in a Chevy Tracker?
Unscrew door handles in front first then just pull off door panels carefully unscrew speakers and replace with new.
What does the p0496 code mean on 2006 Colorado?
Trouble code P0496 means: Evaporative emission system - high purge flow
How do you change the starter for a 1996 Oldsmobile achieva?
All except 2.3L and 2.4L (Quad -4) models
CAUTION: If it has the Delco LocII audio syatem, make sure you have the correct activation code before disconnecting the battery. 1) Disconnect the negative battery cable 2) Raise the vehicle and support on jackstands 3) Under the vehicle disconnect the solenoid wire and battery cable from the stater solenoid. 4) Remove the starter motor bolts 5) Remove the starter motor NOTE: the location of spacer shim(s) 6) Installation is the reverse of removal NOTE: Be sure to install the shim(s) in the same location
2.3L and 2.4L (Quad-4)
See CAUTION ABOVE
1) Disconnect the negative battery cable 2) Remove the intake air duct 3) Remove the cooling fan 4) Remove the oil filter 5) Remove the starter mounting bolts and pull the starter out enough to disconnect the battery cable and wiring harness from the solenoid 6) Lift the starter out between the intake manifold and radiator 7) Installation is in the reverse of removal
Edit: I just did this in my 97 4cyl and I just wanted to add to these instructions that you may have to unscrew the starter relay to get the cooling fan out. The starter relay is right next to the battery. Also, check the wires coming out of the starter relay. There is a purple wire that connects to a connector mounted above the oil filter. It's easy to accidentally unplug when you are installing the new starter, make sure you get it back in there or the car won't start.
Can you turn off the Passenger Airbag on a 2000 Toyota Solara?
Only in the following instances can you turn off the Passenger SRS.
1. People who must transport infants riding in rear-facing infant seats in the front passenger seat. 2. People who must transport children ages 1 to 12 in the front passenger seat. 3. Drivers who change their customary driving position and keep 10 inches between the center of the steering wheel and the center of their breastbone. 4. People whose doctors say that, due to their medical condition, the air bag poses a special risk that outweighs the risk of hitting their head, neck or chest in a crash if the air bag is turned off. If you are eligible, you must fill out a NHTSA request form. Forms are available at state motor vehicle offices and may be available at automobile dealers and repair shops. You may also get one by calling the NHTSA Hotline or visiting the NHTSA Web site. On the form, you must indicate which air bags you want equipped with an on-off switch, certify that you have read this information brochure, certify that you are, or a user of your vehicle is, a member of a risk group listed above, and identify the group. Then send this form to NHTSA. Upon approval of your request, the agency will send you a letter authorizing an automobile dealer or repair shop to install an on-off switch in your vehicle. Warning: It is illegal to turn off the SRS without prior approval from the NHTSA. Do so and you leave yourself open to a lawsuit and your insurance company may refuse to pay for any injuries associated with this.
How do you change a door jamb switch on a 2004 Chevy Colorado?
try coloradofans.comit as everthing you could wanna know about colorados, it has helped me out sooo much
How do you fix a starting problem on a 95 Chevy Caprice?
What is the engine doing? Does it crank over? Does click?
Where is the PCV valve on a 2005 Colorado?
I have a 2004, colorado, and it dont have a pcv valve, just a hose from the crank to the resonator.
How tall is the 2009 Chevrolet Colorado?
The height of the 2009 Chevrolet Colorado is 5 ft. 4.9 in. (64.9 in.).
How long is the 2008 Chevrolet Colorado?
The 2008 Chevrolet Colorado is 16 ft. 0.4 in. (192.4 in.) long.
What could be some reasons why a 1986 Ford Ranger truck will not start?
Loose cables, bad battery, alternator or starter.
How do you change a starter on a 1996 I30?
if you are looking at the engine on the right side you will your air intake that whole sytem needs to come off it will be underneath a lil ways being held on by 3 bolts you may have to move some wire to get to it also make sure all sensors attached to the air intake are taken off and the wire conecting the solenoid on the starter also once you take the trhee bolts off you will have to wiggle the starter as you pull it out then reverse the steps to put it back together
Remove stereo 2005 Chevrolet Colorado?
The trim around the radio can be pulled off, it is only held in by a few clips. then all you have to do is unscrew the radio from the mount. There is nothing to it really.
Why would a 2000 Ford F150 4.6 liter lag when accelerating and vibrate?
It may be a leak in the tube that connects the MAF to the throttle body. If the check engine light is not illuminated, it will make the job of finding the problem a lot more difficult. it could have a pluged fuel filter or a pluged air filter or a pluged catilitic converter. Maybe a bad fuel pump
Where to find a Manual to rebuild 5 speed manual transmission for 1985 Kingcab 4x4?
on e bay ,look for the service manual,i have one.
How do you remove the dashboard in a Chevrolet Colorado?
I don't know personally but http://www.coloradofans.com has a lot of great information. Try it out! tell em Deuce82 sent you ;)
Where is the turn signal flasher relay and emergency hazard relay located on a Chevy Colorado 2006?
According to my local chevy dealer, it is the emergency flasher relay button and flasher assembly all combined. $75.24.
