0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
How do you adjust idle on a 1995 dodge ram diesel?
adjust it with the throttle linkage find your throttle on drivers side next to injection pump and its just 10 mm bolt to loosen and lengthen/shorten to what you need
2007 dodge ram engine light on?
could be a sencor or needs new gas cap,, mine keeps comming on and going off,, gonna try changing cap,, and if doesent work have to takeand get codes read, and if needed fixed,,
Which cars have the same wheels as a 1984 cutlass supreme?
Sometimes the Cutlass sedan and the Delta 88 would share the same wheel design.
What can you do to increase your HP in your 1999 dodge Ram 1500 5.9 L V8?
Get a better air filter system with a chip and programmer and if that's not enough u can get an exhaust system or those cyclone things u put in ur air intake boot another thing would be a turbo charger
How do you remove a motor from a dodge ram 250 van 1989 model from front or out the dog house?
Front, Remove hood, grill, bumper, etc. You could through the dog house if you are superman. Leaning over the seat and picking up an engine is quite difficult.
Where is the vehicle speed sensor on a 1991 Chrysler New Yorker?
Follow the passenger side axle to the transmission, the sensor is located in housing the axle fits into.
1976 dodge 318 oil pressure sensor location?
Behind carb. at rear of motor with little wire going to it.
How do you replace a starter on a 1994 Chevy pick-up?
Hey George===First remove the negative battery cable. Rme ve the flywheel cover. Then remove the bolts holding the starter to the block. Drop the starter down enough to remove the wires. then remove the starter. GoodluckJoe
What do you do if the passenger side window on a 1995 Jeep Cherokee does not work?
check your window lock switch on the drivers door control panel. That is the case with my 1990 works when it wants to.
99 Taurus how do you replace left front brake sensor?
The brake sensor is built into the wheel bearing. The whole unit has to be replaced. It is best to replace both bearings. Left wheel and right wheel ---- 1998 models have the sensors as a separate component - See "Related Questions" below for more
Where is the mass air flow sensor on a 2001 dodge Dakota rt?
Dodge Dakotas do not use mass airflow sensors.
It may bolt in, but will take major modifications to the electrical and computer systems to get it to work.
Why are my Rear brakes sticking on a 2500 ram pick up?
are these drum or disk brakes? if drum, the linings may be worn ,which allows to much travel and the slave cylaner rods get out of alignment.if they are disks, the calipers may have a problem with dirt on the pistons. either system may have a problem with the master cylander and the disk brake system may have a problem which requires new calipers
Where is the transmission filter located on a 2001 Dodge Ram 2500 Diesel?
you have to drop the oil pan on the TRANSMISSION, and you can't miss it, it will be right on the other side.
How much horse power and torque does a 4.7L V8 Dodge engine have?
Generation 2 4.7L 290 hp, 320 ft lbs torque
How do you replace input speed sensor on 1999 Chrysler?
It's not terribly hard, but as is typical with this car, some parts are just not that accessible :) I recommend removing the driver's side tire and the plastic shield that covers the battery. There are 4 locking screws that you will turn 90 degrees to remove the shield. At this point, you will be looking at the transmission from the side. To your left (towards the front of the car) there will be a dark tan screw-in sensor with a wire attached to the front of it. This is the OUTPUT sensor. The input sensor is a few inches further in towards the center of the car. You'll want to find a way to remove the wire from the input sensor and then squeeze a 1" ratchet onto it and unscrew it. Then simply reverse the process to put the new one on. take the air filter off to get to the input sensor. It is tight quarters so good luck. But it's definitely worth trying to do it yourself. $17 part. Took me about an hour or so. I have found an easier way to change the input sensor. Just take off the engine control computer, then the black switch on the tranny, and you can easily reach the sensor. Be careful though, I just got done doing this and now the car will not start, I'm going to take it to a shop tommorow. I'll reply back when i find out what caused this!!!!!!!
How do you replace a steering pump in a 1998 Dodge Dakota with the 4.7L V8?
It is actually pretty simple. First remove the serpentine belt by using a ratchet or breaker bar with I believe a 14 or 15mm socket and pull back to relieve tension on belt and pull belt off. Then disconnect the hose at the bottom of the p/s reservoir by sqeezing the clip and pulling it back and pulling off hose. Then remove the hard line on the bottom of the pump. You will need a 5/8" wrench for that. Remove the power steering cooler mount(radiator looking thing), it is a 10mm bolt. Remove 3 bolts that bolt the pump to the engine by sticking a 1/2" deep socket through the holes in the pulley. Pull off pump. That is it. Job is done.
Where is the oil pressure sending unit on a 1999 Dodge Diesel engine?
it is under the ecm on the left side of the engine. you will haft to take the iner finder to really see it.
well the 426 hemi has 425 horsepower stock and also the 6.1 hemi has 425 and the 5.7 hemi has about 380 horse power it can run the quarter mile around high 13.00 seconds in a dodge ram mabye 15.00 because of the weight of the truck
