0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
What does the rear drive shaft do?
The rear drive shaft on any rear-wheel-drive vehicle is the link between the engine/transmissioni combo and the rear end. It's through this that all the torque developed by the engine is applied to the rear wheels. Nathan
Where is the headlight adjustment screw on a 2007 dodge ram 1500?
I have an 08" Dodge Ram 1500 4x4 and just upgraded to plasma bulbs, Before I did this noticed that the low beams where a little low and intended to raise them when I changed out the bulbs and notice one adjustment screw only,where is the adjustment to raise the low beam?
Jose
How do you fix a faulty Vehicle Speed Sensor on a '90 Geo Prizm LS?
i just came across the same thing within the last week and it wasent a sensor its a cable drivin speedo...if that helps any
Fuses That "Blow" Repeatedly
Without being able to "hands on" troubleshoot the circuit served by the repeatedly blowing fuse, none of us can identify the specific defect which is causing your problem.
Therefore, the following generic answer can be applied to any electrical circuit, whether in a vehicle, or in a building, or whether alternating current [AC] or direct current [DC].
Fuses [and Circuit Breakers] are safety devices designed and installed in electrical circuits TO PROTECT the conductors [wires] and other components from short circuit conditions and/or overload conditions which cause an extremely large flow of electrical current [measured in Amperes], which causes overheating of the conductors that results in damage to the insulation and the conductors.
And in a worst case scenario, the probability of a FIRE which could destroy the vehicle, house, or other structure in which the circuit is located.
When a fuse or Circuit Breaker [and replacement fuses, or repeatedly "tripping" Circuit Breakers] "blow," especially if it happens repeatedly, is an indication of an UNSAFE CONDITION in that circuit, usually a short.
The fuse or circuit breaker is doing what it was designed, intended, and installed to do, protect the conductors and components of the circuit which it serves.
The proper "fix" for this issue is for a qualified technician, who knows what he or she is doing, to troubleshoot the involved circuit, find and identify the defect, and make proper repair [s], BEFORE replacing the fuse again [with the properly sized fuse or before resetting a circuit breaker].
Some ignorant people will suggest installing a larger fuse or breaker to solve the problem, BUT that will only increase the hazard, not correct it.
Do not follow this "bad" advice by installing a larger fuse in a misguided attempt to correct the problem. To install an oversized fuse would almost guarantee damage to the wiring and the probability of an electrical system fire.
Will a 1990 Dodge 360 tbi unit and intake bolt to a 1987 318?
no heads and intake are different form a 360 to a 318
How do I reset check engine light on 2004 dodge diesel 3500?
This question refers to procedures for turning of the check engine light (CEL) on most OBD equipped vehicles. The most common method is attaching a scan reader to the OBD service report to clear the error codes. Another method which may or may not work is disconnecting the battery.
How to Replace door speaker in 2002 dodge ram?
take out all the screws including the one inside door handle. ones you took all screw off. take the door panel out by pulling upward. then pull out a little and disconnect the window and door lock wires. and you will see the speakers. clean n CLEAR.
How do you fix a trouble code p0406 on a 2004 dodge ram 1500?
Exhaust Gas Recirculation Sensor "A" Circuit High. Replace Sensor
The sensor is part of the egr valve. Replace the valve.
What causes the horn to blow non-stop on the 2000 grand Cherokee?
a stuck rely. and some time spring in the button on steering wheel gets stuck too
I would look for a short somewhere in the wiring Harness.Pick up a book with the wiring diagram and test between that fuse and the end of the like where the wires meet the engine to make sure a wire is not broken or possibly ground out,or bare and touching another wire.
my 97 Nissan was doing the same thing, i found on alot of 97 Nissan trucks the same thing is happing, look at the second valve cover bolt from the fire wall it will be under the wires running beside the valve cover on the left side and it rubs a hole thru the insulation in to the wiring and causes a ground all i did was re wrap the wires with extra electrical tape so it could not rub thru as easy worked great
Where is the fuel filter located for a 97 dodge ram?
The fule filter is located on the drivers side of the engine toward the back. There is a metal canister about 3.5 to 4" in tiamiter and about 4" tall. It is conected to the fule system by the top and the filter is inside the canister. It is difficult to access but gets easier after you have changed it a time or two.
What is the cylinder order on a 3.9 liter v6 dodge ram truck?
As with all Dodge truck V6's, the cylinder numbers are 1-3-5 front to rear driver's side and 2-4-6 front to rear passenger side. The firing order is 1-6-5-4-3-2 and the distributor rotates clockwise.
How toTurn off oil change warning light on 2008 dodge ram?
Key on, engine off. press gas pedal to the floor three times.
Where is a PVC valve located in a 1998 dodge ram 1500?
It is the small plastic elbow that is on the top of the valve cover.
Where is the fuse box on a 2005 dodge ram 3500?
In the engine compartment beside the battery on drivers side
What color is the wire leading to the reverse light on a 2004 dodge ram?
The wire is white with a light green stripe on it.
How do you replace the oil pump on your 1994 Chevy pickup?
Need to remove engine mount bolts jack motor up as high as possible best to remove disributor cap as not to crack it remove oil pan remove oil pump and shaft install new pick up screen so that screen is flat with the bottom of pump have to hammer it in using vise grips clipped above ring on screen reinstall shaft and reverse process.
: You mind aswell buy a new motor because the old one could not have survived without the oil pump running. Its also easier/potentially cheaper to slap a rebuilt motor for $900 into the truck, rather than replacing all the gaskets, seals and rusted bolts you will have to remove to change the oil pump.
Where is the oil pressure sending unit on a 1999 ranger 2.5 liter?
The switch is screwed into an oil filter adapter located at the oil filter. You will recognize it by the wiring on it.
Go to a major library and ask if they have Mitchells "on-Line" I copied the entire schematic about 57 pages
good luck, My 07 diesel has lots of computer related problems, Do Not power up with outside power source 12 V or otherwise - you could fry a circuit board.
Dodge has a website www.dodgebodybuilder.com that has wiring diagrams on line for the chassis cabs.
Also you can call them directly at 866 205-4102.
