0
Ford Bronco II
The Ford Bronco II, a smaller version of Ford Bronco, is a compact SUV produced from 1984 to 1990. The Bronco II offers optional 4WD, mechanically identical to Ford Ranger, but does not have a removable roof.
1,174 Questions
Where can you get an engine wiring diagram for a peugeot 106 1.4 xsi?
peugeot.mainspot.net
i couldn't find the diagram..1.4xsi's are tu3 engines :/
Does a 1997 Geo Metro have a modulator valve?
Are you referring to the transmission? If so, the answer is no.
How do you replace the headlights in a 1993 Mercury Topaz?
The passanger side is easy. First remove the power connector, then twist the round ring till it comes off, then pull the bulb out. On the Drivers side , get ready for this, the battery must be taken out to remove the headlight. Once this is done, it,s the same as the other side.
Did you try putting gear shift in "neutral" when shifting into 4 WD Low?
How do you get a harmonic balancer off a 1995 dodge neon?
you need a gear puller so you don't damage it.
It's either a bad switch or an intermittent connection in one of the wires.
How do you replace a master cylinder on a 1992 Chevy Lumina?
Replacving a master cylinder is usually pretty straight forward. Remove the brake lines, unbolt/remove the master cylinder, Re-install in reverse order. The hard part is bleeding the new master cylinder/brakes once you put it on. Caution: Your life depends on your brakes. If you're not sure you can do it right... don't. Get someone to help you.
Where to purchase filter to carb fuel line 1988 Bronco ll V6?
at your local automotive parts distributer
Where is PCV valve located on 1987 Ford bronco?
The pcv is located on the passenger side of the motor, under the edge of the intake manifold, in the back.
Where is the fuel pump located on a 1996 ford bronco?
On a 1996 Ford Bronco :
The ELECTRIC fuel pump is INSIDE the fuel tank
* it is installed through an access hole in the top of the tank
Where is the ecu on o a ford bronco II?
its on the left side of the brake and gas peddling and/or clutch.you may need to remove a piece of the doors lineing panel to acces it.to remove it you must loosen the bolt in the electrical plug which should use a 10mm socket and the bracket which uses (in some cases)an 11/32 socket. after this the ECU shoulbe free to remove
Where is number 1 cylinder on distributor cap on 2.9 liter ford bronco ii?
It should be marked but if not the number one is usually the stud right next to the firewall if the screws for the cap are parallel to the firewall
What engines will fit a 1988 Bronco II 2.9 liter 4X4?
i have a 390 big block with a 4 speed in my bronco 2
Is there a 2 speed rear end for an 88 Chevy 2500 with a 350 and a 4 speed manual trans?
Very unlikely Most likely have to change gears in rears
AnswerI worked at a place that had a small Chevy flat bed and it had a 2 speed rear it was in the 80s the cab was small like a pickup -- rear should fit if u find one let me know the gearing i would like to put one in a new dodge for drag racingHow do you change a window on a Ford Bronco II?
I have replaced the front manual roll down window. You need: Phillips and Flat Head screw driver #10 torx Head 2 1/4"x2" Screws A Drill and bit to remove 2 pop rivits.
1. Remove the door panel. (remove screws in the door opener, and door puller assist, and window crank). The window crank I believe is a #10 Torx head. Then with a screw driver pop each plastic from the door.2. Remove plastic liner from the door.3. Clean all debris from inside the door (glass maybe...)4. If you have a used window, Drill out the pop rivits from the plasic assembly. Remember how they go on there!5. Obtain 2 - 1.4"x2" screws, with lock nuts.6. Slide window in sideways.Once in the door flip window to the correct orientation.7. Now take your plastic assemblies from step 4, and put them back on the windows using the screws, and lock nut.8. Adjust the window scissors down, and move the window up (by hand) then back down till they are in the brackets, they should lock into place.9. Replace liner and door panel and attachments.
I personally replaced the door liner as it does keep alot of road dust out of the truck. I used another piece of heavy duty plastic and some silicon sealer.
How much oil does a 2.8 liter ford bronco 2 engine hold?
With engine oil filter change :
The 2.8 liter V6 engine in a ( Ford Ranger ) holds ( 5 quarts )
Just finished replacing fuel pump on my bronco 2 . Mine was a mechanical pump located on engine block behind and below power steering pump. Pain to get off without flex rachet extention or socket swival. Mine had NO fuel pump on it.
How much nitrous can a stock 2.8L V6 take?
i would say to you not to use nitrous on a stock engine. clumy and stupid move. parts can easily break so if you wanted to get a reasonable amount of horsepower, replace the crankshaft, pistons and rings, con rods, and probably the intake and exhaust manifold. its not an easy thing......
Actually it is an easy thing if used in moderation......Start with an adjustable kit that adjusts from 50 to 100 horse........I used a 100 horse nitrous kit on my 2.8 with cast pistons and NEVER had an engine failure....Again if you put a 400 hp kit on a stock bottom end then of course you are going to have problems but mild kits are made and those are the ones to use on stock bottom ends.....
Why press the fuel pump reset button?
The fuel shutoff will cut off power to the fuel pump in the case of an accident. A very good reason to push the button then is if you desire to get your vehicle running again. See "Related Questions" below for more
