0
Headlights Tail and Brake Lights
Headlights, Tail, and Brake Lights are warning lights on a vehicle. Tail is a marker for the vehicle following it. The brake lights signals if it is braking. The headlights illuminate the path and are markers for oncoming cars.
11,233 Questions
How do you replace a headlight bulb on a 2003 Ford Explorer?
On the top of each headlight assembly, you will see two small semi-circular tabs. Pull these tabs upwards - you may have to use a wrench or screwdriver to put some force into it, as they tend to get stuck with road salt and grime. Once they move upwards, about 3/4 inch or so, the headlight assembly will release. You can then pull the headlight assembly forward and out of the truck. It will be attached only by the wires. Rotate the lightbulb assembly counter clockwise, and the bulb will come out. Replace the bulb, put it back into the headlight assembly, and rotate it clockwise to lock it in. Replace the headlight assembly, making sure the three screw/nuts are in the locking tabs correctly. While pushing the headlight assembly inwards, press the two locking tabs back down. This will lock the headlight assembly back into the truck, and realign the headlight, so that it does not have to be aimed again.
How can you clean INSIDE the headlight covers on a 1997 Mercury Sable sable?
Not too long ago I took one of my headlights off the car to see if I could get into very easily - it had all sorts of condensation in it.
Now, I'm pretty good at figuring out how to *disassemble* things, but the headlight stumped me. It just wasn't readily obvious how to get to the inside.
I ended up pointing a hair-drying at the opening for 1/2 the afternoon and that cleared up the excess moisture.
See "Related Questions" below for information on removing the headlight (it's really easy)...
How do you change the upper brake light on a ford s-max?
the high level stop light is a bulb and not an LED. To remove the light to access the bulb you first need to remove the top interior tailgate trim. Once this is off you can then see the two holes to access the retainers for the lamp. These retainers are spring loaded to release them you need to push them towards the center of the lamp, there are four in total, the best tool to release them is a long thin flat bladed screwdriver which you can use as a lever to push the retainer in.
Once the lamp is out you can replace the blown bulb. The bulb is a large cap-less 21W bulb
96 Dakota no headlights all other lights work why?
Bad bulbs, bad switch, bad circuit breaker, bad wiring, bad ground.
How do you replace the headlight bulb located on a 1998 Mercedes c230?
Remove the plastic access panel by pressing down on the tab at the top of the penel and pulling the top of the panel towards the engine and off. Needle nose pliers may help with the next steps to remove the spring clips. There are 2 bulbs, the top large bulb is the low beam. To remove it, first remove the socket attached to it, then press the top of the metal spring clip towards the front of the car and towards the passenger side (look closely at the clip to see the latch holding it. The clip then swings back towards the engine. Remove the old bulb, install the new bulb, replace the spring clip, re-connect the socket. (Don't touch the bulb, if you do clean it off with a lint free cloth and alcohol). To replace the lower bulb (parking light), remove the socket, then release the lower end of the spring clip, look closely and you'll see the latch holding it. You have to press it towards the front of the car and swing it towards the passenger side. It will swing up and release the bulb. Replace with new bulb, replace spring clip, connect socket. Don't forget to replace the plastic cover panel by inserting the bottom tabs into the sockets and snapping it closed at the top by pressing it towards the front of the car. Open up the hood, and go in behind the fixture where the light is located. Sometimes there is an access panel on top. Open it and reach down inside and grab the bulb's socket. Twist the socket a quarter turn counter clockwise, and pull out the socket. Grab the bulb, and pull it straight out. To replace the new bulb, never touch it with your bare fingers, as this will greatly shorten the bulb's life, if it even work's at all. Use a tissue or something else in that order to handle the new bulb. Push the new bulb into the socket, put the socket back into the housing, and twist a quarter turn clockwise to secure the socket into the fixture.
Addendum: Make sure NOT to completely remove the metal latch holding the socket and light in the hole; just unlatch it and swing it back. If the two prongs at the bottom come out of their holes it is difficult to get them back in, especially with the extremely limited space in that location.
Need to remove headlight lens cover have moisture inside on 1993 Ford ranger?
I detail headlights at used car dealerships and what I do is drill a TINY hole on the lower edge of the headlight to let the water out. The heat from the light bulb will eventually dry it out. To clean the outside of the lens I use a product called CrystaLenz, this stuff really works great. Check out their website www.CrystaLenz.com for more information. ==Answer == You can also dry the lens out by talking the bulb and socket off the back and inserting a dry clean rag or towel through the opening and clearing the lens from the inside with a long object like a wooden stick. Once a hole is drilled, moisture can re-enter of course if not plugged with something like silicone. I have had the same problem.
How do you align or aim the headlights on a Nissan Altima?
On models 1996 onwards (this might also apply to earlier models), there are vertical and horizontal alignment screws on the front part of the engine compartment. The position of these alignment screws, and the associated water level indicators that you can use to align the headlights are illustrated in the Nissan Altima Owner's Manual, which can be downloaded for free from Nissan's website at: http://www.nissan-techinfo.com/nissan/deptog.asp?dept%5Fid=40
What color is the high beam wire on a 1998 Ford F-150?
wiring diagram in a PRO manual everyone should have a manual for their vehicle, and the library should have a professional shop manual available in the reference section for FREE to make copies of...read up and fix like a pro!! :) Dave
How do you change the headlamp bulb on a 1997 Lincoln Mark VIII?
If you are referring to the lamp that lights up when you open the doors and is located over your head. You carefully remove the plastic cover being sure not to snap anything. Inside will be either what looks like a bulb or a fuse and you take that out, carefully too. You take it with you too the autoparts and get replacements. Reinsert the same way you took them out and gently snap on the cover. If it still doesnt work then that can be a fuse located in the fuse box. Now sometimes people refer to the headlights as head lamp and in that you cannot replace the bulb you have to buy the whole lamp from either a autoparts or dealer. With this you lift the hood and look behind the lamp. It should be inserted into what looks like a plug. You disconnect the two gently and be sure to not disconnect by the wires, hold them by the connection pieces. You may want to disconnect the battery before doing this too.
Why wont brake lights shut off on your Pontiac grandprix le 1992?
The most likely cause is a defective brake light switch; It is located towards the top of the brake pedal.
When I signal left the right backup light blinks why?
Does the turn signal also blink? If so, you have two wires touching. What happens when you put the vehicle in reverse and the backup light is supposed to come on? If the turn signal lights up and the backup light doesn't, you have the bulbs in the wrong socket.
Get the green arrow to stay on. Now get out of the car and walk around it, looking for the turn signal bulb that stays on. That bulb has a bad ground. I fixed mine (very) temporarily with aluminum foil, then later by running a new ground wire. I just wrapped stripped wire around the base of the bulb and ran it to a ground.
Fuse for brake lights on Hyundai Accent?
The fuse for the brake light on a Hyundai Accent are found in the engine compartment. The fuse is number four in the fuse box, and is rated on 10 amps.
No the high beam filament is independent from the low beam filament You can run them seperately or together . it depends on how the lights are set up. For instance if you have your high beam on you may have your lows running at the same time, however if your low beam is on low beam setting, your highs are always turned of It sounds like you may need to look at your fuses or your switch.
How do you get ABS and brake light off 96 dodge conversion van?
Have the abs system checked for codes and repair the cause.
Have the abs system checked for codes and repair the cause.
What causes the brake lights on a Toyota pathfinder to go out?
Brake Light Troubleshooting (check in this order):
- Check Fuse
- Check Bulbs
- Check switch on brake pedal
- Check license plate light bulb and wiring
- Check Towing Harness Wires
- Check all wiring harnesses and wiring for shorts
Most likely its the fuse or a burnt bulb breaking the circuit. See sources and related links below for bulb information. Sometimes the license plate and/or the trailer hitch is wired into other circuits and can cause issues in other areas. Sometimes its wires grounding out somewhere on the vehicle. See sources and related links below for bulb information. See owner's manual for location and identification of fuses.
How bright should your headlight be?
In the USA - Lowbeams are 55 watt and high beams are 65 watt. Don't worry about brightness - purchase lamps by correct part numbers. See sources and related links below to lookup your vehicle(s).
How do you change left brake tail light bulb out of a 2008 Nissan Sentra?
2008 Nissan Sentra tail light bulb replacement: Purchase the correct replacement tail light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the tail light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
Daytime running lights 2006 corolla?
The daytime running lights on the 2006 Corolla are a safety feature. They are designed to make it easier for other drivers to see the vehicle.
How do you replace a headlight bulb on a 2000 Saab 9-3?
2000 Saab 9-3 headlight bulb lamp replacement: Purchase the correct replacement headlight bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the headlight bulb lamp replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
How do you replace the headlight bulb located on a 1999 Oldsmobile Alero?
lift hood,on top of the headlights are tabs to pull up.pull the tabs up and pull the headlight towards you and it will make the bulb holders visible
How do you replace the headlight assembly located on a 1994 Ford Ranger?
detach the bulbs and remove the clips behind the headlight assembly
IF THIS ONLY HAPPENS WHEN YOU APPLY THE BRAKES THE MOST LIKELY PROBLEM IS THAT YOUR FRONT BRAKE ROTORS ARE WARPED. YOU CAN EITHER HAVE THEM MACHINED AT A QUALITY AUTOMOTIVE SHOP OR REPLACE THEM WITH NEW ROTORS.
Where is the fuse box on a Citroen C3?
The Citroen C3 has two fuse boxes. One is under the bonnet just to the right of the battery. It has a plastic cover that is quite hard to get off but there's a catch in the middle of the side facing the battery press the centre of this in with a screw driver and pull the cover. The second fuse box is inside the car in the glovebox. There is a grey plastic cover at the left side. Prise this off to reveal the fuses - really awkward to get at!
How do you change headlight bulb on a 2009 Nissan Titan?
2009 Nissan Titan headlight bulb replacement: Purchase the correct replacement headlight bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the headlight bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
