0
Nissan Pathfinder
The Nissan Pathfinder is a sport utility vehicle (SUV) built by Nissan Motors from 1986 to the present. The car is slotted in size between the Nissan Armada and Nissan Murano, but in price between the Nissan Murano and Nissan Xterra.
2,681 Questions
What kind of gas should you use?
There are number of different kinds of gas you should use. The gas you should use depends on the situation.
How do you remove crankshaft pulley 1997 Nissan Pathfiner?
Hello,
I am copying the answer from my Nissan Pathfinder repair Manual.
This is for 2.5L and 3.3 L engines, NOT THE 3.5 L ENGINE!!!
1- Disconnect Negative cable from the battery. Rause the front of of the vehicle and secure it on jackstands.
2. Remove the engine under cover. Remove the lower radiatorshroud and remove the engine colling fan.
3. Remove the drivebelts.
4. Use a strap wrench around the crankshaft pulley to hold it while using a breaker bar and socket to remove the cranshaft pulley center bolt.
5. Wedge a prybar or two screwdrivers behind the crankshaft and carefully pry it off the crankshaft. If the pulley is difficult to remove, use a jaw-type puller and pull it off.
Installation is the reverse of removal. Tighten the pulley bolt to the torque listed in the manual, then adjust drivebelts.
Hope this helps-S
How can I tell whether my starter of flywheel is bad on my 94 Nissan Pathfinder?
if the starter is bad you will hear one single click, if the flywheel is bad it will sound like a heard of daemons are trying to exit from under your vehicle. if its your flywheel you will know what i mean by the comparison
Why is the gas gauge saying empty when there is a full tank of gas for 2006 Nissan Pathfinder?
Fuel sending unit more than likely has failed. Normally will set a code stored in ECM, pretty common problem. Counter measure sending unit is available. Don't for get to replace O-Ring when replacing sending unit.
How do you program the garage door opener in the visor of a 1996 Lincoln Mark VIII?
Depends on the garage door opener you have. For the most part hold the button on the visor until it flashes fast, or slow, Just so you see the light change. Then hold the button on you garage door remote next to the visor until the light on the visor changes again. This should do it. Now if you have a rolling code garage door opener then you need to locate the learn button on the garage door opener motor. Press the learn button until it changes and then run to your car and press the visor button until you see the light on the garage motor hold steady. Good luck.
Also, try www.homelink.com
Why does 89 caprice stalls when turning corner?
It is possible that a 1989 Caprice will stall when turning a corner if the idle is not turned up high enough on the carburetor. It is also possible that the flow of gas is disrupted by a loose fuel pump when the vehicle turns a corner.
How do you replace the water pump on a 1987 Ford Aerostar 6 cylinder?
If it is anything like the 92 Aerostar, you have to remove the air filter hose, then remove the fan shroud, then remove the fan and pully (along with the belt, then you can unbolt the water pump and it will come straight out toward the radiator because of the impeller shaft on the inside. It is about a 4 hour job for an intermediate mechanic.
Ford Aerostar Water Pump replacement Engine Size: 3.0 V6 Front Wheel Drive
Total time with new belts and hoses, 2.5 hours. I did it on 11/25/2006 for my pops.
Parts and Supplies Needed:
New Water Pump Water Pump Gasket Water Pump Gasket Glue Blue Loctite RTV (I Used Orange) Wire Wheel on Drill (to clean corroded bolts) 13 mm and 8 mm sockets w/ extensions Optional : new belts
Air tools are helpful if you have them.
Large and small ratchets
Where do you start? - drain coolant from lower radiator hose, keep it disconnected - remove top radiator hose - remove airtube from throttle body and airbox, put it aside - remove the fan (turn clockwise with wrench , jam a pulley to keep it from rotating, hit wrench with hammer, loosen it off the mount and keep it there for now. - remove two upper fan shroud screws and remove fan and shroud at same time - remove belts by loosening alternator and loosening power steering pump, remove small plastic serp belt pulley to remove serp belt. (13mm socket) (DRAW DIAGRAMS!!!) - remove pulley with impact driver (13mm wrench)
Remove the water pump by undoing all bolts - keep track of which bolt went where (DRAW DIAGRAMS!!! Trace the new pump and poke holes where the screws go.) - clean all bolts with wire wheel if needed - remove the water inlet feed on the old pump
Remove pump when all bolts are out - clean entire gasket surface - use razor blade - dry surfaces
Prepare the new water pump and gasket: - apply gasket goop to the engine side of the water pump gasket - apply goop to the pump side surface of the water pump ITSELF!
Installing new water pump: - make sure engine block surface side is clean - stick the gasket to the surface lining up holes - put the pump on, have bolt in hand to thread in and hold it - torque all bolts down, I do it by feel - reinstall the inlet hose to the new pump
NOTE!
On all bolts going into the pump use rtv on the smooth surface of the bolt and use blue loctite on the threads!!!
Let it sit for about an hour or so, look at your fine mess and appreciate a day�s work.
Then�.
- Reinstall the pulley on the pump - reinstall the belts in correct order (small one first towards the engine) - fat one towards the front., reinstall plastic pulley to keep it all together
Tension the alternator to take up slack in Serp belt. Tension the power steering pump with a �� drive ratchet in the square hole to leverage tighten the accessory belt, hold pressure and tighten bolts simultaneously.
Flush your cooling system at this point in time with a garden hose and sprayer.
Reinstall and secure all cooling system hoses - lower radiator hose - upper hose
Reinstall the air tube
Fill cooling system up with coolant and 50% water
Get in, turn engine on and let it idle to operating temps, check for leaks.
If you suspect a false leak drive it for 20 minutes and come back.
Job well done. Not that hard for a day�s work.
What is the maximum cargo capacity of the 2008 Nissan Pathfiner?
The maximum cargo capacity of the 2008 Nissan Pathfinder is 79.2 cu.ft..
A wiring diagram for a 2005 Nissan Pathfinder?
Try this web site. It might be of some use to you.http://pdftown.com/search/node/nissan+pathfinder Regards Dave
What is the firing order for a 76 460 and what would be a good refrefrence for the timing mark?
the firing order is 1,5,4,2,6,3,7,8 the cylindes are starting at the front on the pas. side front to rear 1,2,3,4 and on the drivers side front to rear 5,6,7,8.... hope this helps
Where can you get a wiring diagram for a 93 Nissan Pathfinder?
http://www.Google.com/images?oe=utf-8&rls=org.mozilla:en-US:official&client=firefox-a&saf
e=images&q=pics+of+a+diagram+for+93+Nissan+pathfinder&um=1&ie=UTF-8&ei=LxnGS7
HnE5C4swPzv9i2DQ&sa=X&oi=image_result_group&ct=title&resnum=1&ved=0CBQQsAQwAA
A type in this web address exactly and youll get the diagram ok
Replacing front wiper motor on a pathfinder?
where is the front wiper motor located on a 99 pathfinder
How do you replace a power antenna on a 2000 Pathfinder?
I replaced my 95. I pulled the front right wheel and inner wheel well (plastic). It is above that on a small bracket. You'll need to remove the special nut on top to lower the ant down. I used (carefully) a pair of vice grips....No problem job.
How do you change a fan belt in a Camaro?
You should just have to take a 1/2" ratchet, put it in the tensioner, pull back to release the tension and then slide the belt off. The new one will just slip on. That's if you have a serpentine system. If you have a v-belt system then you'll have to loosen one of the mounting nuts (usually for the AC compressor to release the tension.
If you have more info I can probably help more.
Mike
How do you replace the water pump on a 1995 Dodge Intrepid 3.5L?
If it's the same as my 97 3.5L it is located behind the timing cover. This is a 3 piece cover. Remove all 3 pieces, remove timing belt, and you can change water pump. Make sure not to mess timing up while your in there. I missed it by one tooth and had to go back in to fix it.
How do you replace the water pump on a 1995 Saturn?
1. jack the vehicle up on both sides, use jack stands if possible.
2. Remove Passanger front tire, along with plastic splash shield
3. Drain coolant
4. With serpentine belt still installed, loosen the 3 bolts on the water pump pully, don't take them all the way off, just loosen them.
5. Use a 14mm wrench to reduce tention on the serpentine belt enough
so you can slide the belt off
6. Remove the water pump pully bolts, remove pully, or let it rest on the
pump shaft.
7. Remove water pump housing bolts (6 of them) and discard the gasket
8. reverse procedure to reinstall new water pump
What number fuse is the turn signal on a Plymouth Sundance?
It's a 10 amp fuse, but, at least on my '94 model, it's in position 15, which is on the far right, one down from the top. the number on the fuse is ten
How do you remove the stereo in a Sunfire?
This is a copy of a post from some time ago. It's specific to my '96, but might help you figure out what you need to to.
Good Luck!
Let's see. First, open the glove box door. You can make it drop all the way down by flexing the little plastic piece that stops it from dropping, to the side. This gives you room to work. On the left side of the glovebox face, you will see a screw or two that hold the piece of molding around the radio on. Remove those screws and pull off the molding. Once the molding is off, you'll see a screw on each side of the radio, which holds the radio bracket to the dash. Take those out, then slide the radio forward. There is a connector which needs to be carefully removed from the back of the radio. The antenna needs to be unplugged too. Then the radio will slide right out. Installation is the reverse. FriPilot
