0
Toyota 4Runner
The 4Runner is a mid-size sport utility vehicle (SUV) produced by Toyota Motor Corporation since 1984. This SUV is offered in four-wheel drive (4WD) and rear-wheel drive (RWD) layouts.
3,192 Questions
How do you remove the cigarette lighter from a Toyota 4Runner?
To remove a cigarette lighter from a Toyota 4Runner, pull the lighter straight towards you. Pull gently until it becomes free.
How do starting blocks help runners?
For a start, I imagine they give a good surface to push off of, both for grip and angle
They also make sure everyone starts exactly where they're supposed to...if you were running against Usain Bolt or Ashton Eaton, you'd probably want to start ahead of them. Starting blocks make sure you don't do that.
What your computer is doing is trying to download some sort of updates for a Hewlett Packard product.If you have recently added a new piece of hardware (Printer, fax etc.) or a new program (Game, software etc.) then there is probably some sort of conflict going on between two programs. Delete whatever was the most recent and see if you still keep getting this error. If the last thing you added to your computer was the "HP" product in question, uninstall it. Then double check that your PC meets the system requirements needed to run whatever it is that you want to add. Then try to reinstall it and pay close attention to the instructions on installation. Hope this helps you.
AnswerThis error message probably occurred, because a spyware removal application incorrectly detected the Updates from HP/Compaq Connections client software (developed by BackWeb Technologies), as spyware and improperly removed it. Since only part of the client software was removed, it cannot fully load when Windows starts and the error message above displays.Uncheck the Updates from HP or HP Updates or Compaq Connections entry from the startup tab of MSCONFIG window.Perform these steps to launch MSCONFIG window.Click on Start->RunType MSCONFIG in the open boxClick Ok
Click on the startup tabUncheck the entry listed as Updates from HP or HP Updates or Compaq ConnectionsClick Apply and Close
The system would be required to restart after perfoming the steps and on restart, in the System Configuration Utility window, click Do Not Show this Message > Click Yes.
Then, visit the below website to download a third party uninstaller utility to remove Updates from HP or HP Updates or Compaq Connections listed. This would fix the issue completely.
http://acelogix.fileburst.com/au.exe
Click on the save button when prompted and save it onto the desktopDouble click on the downloaded icon and follow the onscreen steps to install it.
Follow these steps after installation, launch the Ace utilities programClick on Optimize buttonClick on Uninstall ManagerSelect the program you want to uninstall and Click on remove option
How do you change out the rear end on a 1989 Nissan 240SX?
Tools needed: 14mm socket 12mm socket 18mm socket 12mm open end wrench 14mm open end wrench Hopefully someone to help.
Steps:
1.) Pull the ebrake
2.) Make sure transmission is in neutral
3.) Jack up the car and put on 4 jack stands.
4.) Remove drive shaft bolts from the rear end carrier, this should be 4 14mm bolts which you will need to do 2 at a time. Once the first 2 are removed, disengage the ebrake, rotate driveshaft until the other 2 bolts are visible, pull the ebrake again (this is where having someone to help, well, helps).
5.) Disengage the ebrake Unbolt the axles, depending on the year and other factors, your car may have 5 bolt or 6 bolt axles. Unbolt the axles with the 12mm socket and open end wrench.
6.) Slip the axles off of the carrier
7.) CATION: When doing this, it helps to have a second person or a jack stand under the rear end as it is heavy and will more than likely break your face. Unbolt the 2 carrier bolts which are attached to the sub frame with 18mm socket.
With this, the rear end should come out with some finesse. Good luck.
What are head torque specs for a ka24de?
26 ftlbs then another 79 ftlbs. Loosen all the bolts and then a final 69 ftlbs
How do you disarm an alarm on a 1997 land cruiser?
My battery went dead. I am trying to jump start the 97 landcrusier and the alarm is going off. I did not set the alarm The car sat in the garage for two weeks and battery is dead. Alarm is set and I need to get it of to start the car via cables. help George We have a 96 Land Cruiser. The battery went dead and we dealt with the same problem when trying to recharge the battery. We discovered a toggle switch on the drivers side under the dash below the hood latch and gas levers. Flip that switch and you should be good to go. Apparently it resets the alarm.
How can i remove or bypass the throttle sensor?
You cant,Replace it if that is your problem,Its all in the computer network and cannot be removed.it tells the computer where the throttle is so it can deliver the correct air and fuel to the combustion chambers.....
When should timing belt be changed on a 2005 v8 4runner SR5?
Is it worth it to change if I want to drive it up to 175k miles?
Where are the rear abs sensors located on 1997 Volvo 850?
usually at the outer ends of the rear axle behind the backing plate
How many gallons of fuel does a 99 4Runner hold?
I have a 99 4Runner SR5; I believe it is an 18.3 gallon tank, but don't quote me on that. It is at least 18.
How do you replace the gear shift handle on a 1994 Cadillac Seville?
I believe there is a pin on the back of the shifter knob.I don't remember which way it comes out, when you look at it you will figure it out, but when it does, the knob will come off.
Where can I find vacuum hose diagram's for an 88 Toyota pickup fuel injected?
== == == == Your best place is to find a manual, either chilton or hayne or one from Toyota. They will show several different diagrams for the different years the books cover. I have had no luck locating one online myself. The other option is visit the local library and check out their manuals. Then you can see which is best before buying one.
S100
What is the engine oil fluid capacity on a 2004 4Runner with a V6?
The 2004 Toyota V-6 engine oil capacity is 4.5 quarts. 4.0 quarts will go into the engine and one half quart will go into the oil filter.
How do you clear the diagnostic code on a 1995 Nissan Altima?
small panel on right side of gas pedal pull it off computer is silver box look for flathead screw turn on ignition (dont start) turn screw all the way counter clockwise and then clockwise turning screw from one stop to the other be sure that you completely turn it both ways until it stops or computer might just do a self diognostic test but not reset any codes
Will a 3.4 L engine from a Toyota T100 fit in a 1990 4runner?
If you have the 3.0L engine with a manual transmission it is a direct bolt up i dont know about the automatic but i am sure it is the same if you are switching from a four cylinder to the 3.4L then it requires a lot more work but it can be done a well
How do you fill the transmission fluid on a 1993 Toyota 4Runner?
All automatic transmissions fill thru the dipstick tube.
Is a 2002 Toyota 4 runner front wheel drive?
No , a 2002 Toyota 4 - Runner is rear wheel drive or 4 wheel drive
Where is the clutch bleed line in a 98 Toyota 4-runner?
at the caliper and drums derrr! at the caliper and drums derrr! no its under the car where the clutch line goes into the trani at. they should be a 8mm nippple sticking out
What are the head torque specs for a 1988 Honda Prelude DOHC 2.0L Si?
49 ft. lbs. Start tightening from the center outward in a criss-cross pattern working your way out from center. Set torque wrench at 22 ft-lbs and do all ten in pattern above. Then set at 36 ft-lbs and do all ten. Finally, set the torque wrench at 49 ft-lbs and go slowly. If you feel a stud not locking in as the others did, STOP! You may have a stripped stud. Do not go back to that stud until all the others are OK. Remember! BEFORE THE STUDS GO ON, 1.) Get a tap and tap the holes in the block. Blow the holes out with W-D 40 and then use a can of "air" to blow out the W-D 40. 2.) Get a die for the studs and mount each stud in a vise. Run the die down the threads to clean and reform the valley-peaks. 3.) Add a VERY LIGHT amount of oil to the threads before they go in. This will give accurate torque readings when the studs are installed. The torque values here are for WET threads (not dry as usual) Recheck the studs at the 100 mile mark (as per a tech at the dealer).
How can you reset your maintenance reminder light on your 1995 Ram 3500?
The SRI lamp may only be reset with the use of a DRBII scan tool, or equivalent. If this is not available, you will have to take the vehicle to a properly equipped shop for them to reset the lamp.
How do you change a rear windscreen wiper on a peugeot 306?
take wiper bolt of then take bolts of from under boot discconect wire then refit new 1
What is the fuel pressure on a 92 v6 Toyota pick-up?
Ignition sw on but car not running between 38 and 44 psi Car running and vacuum hose attached to sensing unit 33-37psi
What is the drivetrain warranty on the 2013 Toyota 4Runner?
The drivetrain warranty of the 2013 Toyota 4Runner is 5 yr./ 60000 mi..
Where is the Engine number location 1993 190e?
Should be on the block, check right behind the alternator on the Block. If not there then check on the datacard that came with the vehicle. You could also try the dealer, as they have a complete record on all the cars from that period.
