VW Jetta

Sensors are located under the floor mats at the front edges of the seats when they are fully to the rear. There is a box type reinforcment that runs from side to side in the floor. The fronts of the seats arebolted to this frame member. The sensors are bolted to a mounting panel that is bolted to this frame member near to the doors. Easiest way in is to remove the seats. Pull the trim panels at the bottom of the door frame out. Lift the carpeting and padding and there they are.

To program the door lock on a Renault Scénic II to lock and unlock all doors simultaneously, you typically need to use the vehicle's central locking system settings. Start by inserting the key into the ignition and turning it to the "On" position without starting the engine. Then, press and hold the lock button on the key fob for a few seconds until you hear a confirmation sound or see the lights flash, which indicates the programming was successful. Consult the owner's manual for specific instructions, as procedures can vary slightly by model year.

The water level DECREASES because: As you boil water, the bonds between water molecules are broken and they turn into gas. The water vapor rises leaving less liquid water then there was before.

On my 1994, the CRANKSHAFT POSITION Sensor (or sometimes referred to as Engine speed sensor) is located behind the Oil Filter & Front motor mount near the starter. It's really hard to see, and even harder to get to.....

The gas door release on a 1996 Jetta is typically located on the driver's side, either on the floor by the driver's seat or on the dashboard. It is usually a lever or button that you push or pull to open the gas door. If you’re having trouble finding it, refer to the owner's manual for specific instructions.

The gas filler door release lever on a 1997 Saturn 2 door is usually located on the driver's side, either on the driver's door panel or on the floor near the driver's seat. It may be a small lever or button that you pull or push to release the gas filler door. If you're having trouble finding it, refer to your vehicle's owner manual for specific instructions.

To replace the grille on a 2007 Chrysler 300, you would typically need to remove the fasteners holding the old grille in place, disconnect any wiring or sensors attached to it, and then install the new grille by securing it with the fasteners and reconnecting any wiring. It's recommended to refer to the vehicle's manual for specific instructions tailored to your car model.

# Turn off the power to the lamppost circuit at the breaker box. # Unscrew the mounting screws holding the lamp in place, and pull the lamp fixture from the post. Remove the wire nuts, and use the circuit tester to be sure the power is off. # Disconnect the wires to the fixture and the photocell. # Disconnect the locking nuts that hold the existing photocell on the post, and remove the photocell. If your lamp doesn't have a photocell, you'll need to drill an access hole in the post to install one. # Install the adhesive foam ring (provided with the photocell) around the mounting hole. # Run a bead of silicone sealant around the photocell where it will press against the interior of the lamppost. # Push the sensor through the mounting hole, and secure it with a locking nut. # Add silicone sealant inside the lamp fixture at any point where moisture might leak through to the photocell. # Connect the white wires from the power supply, lamp, and photocell together. Secure the connection with a wire nut. Connect the black photocell wire to the black power supply wire in the same manner. Connect the black lamp fixture wire to the red photocell wire and secure the connection with a wire nut. # Reainstall the fixture on the lamppost.

The low coolant level light turning on suggests that there might be a leak in the cooling system causing loss of coolant. It is important to check the coolant level, top it up if necessary, and inspect the system for any leaks to avoid potential overheating issues.

If the 304 Stainless surface is polished, then using a buffer is a good solution. However, if it has a grain finish, then the buffer will only produce a bright spot where the scratch was and it won't match the surrounding area. What needs to be done for scratches in brushed grain Stainless steel surfaces is to use abrasives with mineral grit embedded that will remove the scratch and replace the grain. However, the repaired surface will still be brighter than the surrounding area due to the fact that it will be newly exposed metal and the surrounding area will be oxidized (oxidation is what gives Stainless steel its rich, warm color). The only system that accomplishes both repairing the grained surface and oxidizing the repair to blend in to the surrounding area is Scratch-B-Gone. Many retailers now carry this system (do a Google search to find many of them). As well, now most Stainless steel appliance manufacturers use, sell or recommend it to their customers.

buff them out with a buffer

To change the temperature flap lever in a 2003 Volkswagen Jetta, you will need to remove the dashboard to access the HVAC system components. This can be a complex and time-consuming task, so it may be best to consult a professional mechanic for assistance. The mechanic will likely need to disassemble the dashboard to access the temperature flap lever and replace it accordingly.

The liquid in the radiator reservoir of a Volkswagen Jetta 1999 should ideally be a mixture of water and antifreeze (coolant). This mixture helps regulate the engine temperature and prevent freezing or overheating. It is important to check and maintain the proper coolant levels to ensure the engine runs smoothly.

outside temp has nothing to do with engine temp, you just have to leave it running for a little bit. i would suggest at least 5 min. Bad thermostat. Probabl;y stuck wide open. or it is heating up, but your coolant temp sensor is bad and it is saying it is cold

Purchase a tach and it will come with instructions for installation.

There is a product called "Tiny Tach" used for ultralight airplanes. Very accurate digital, does not care how many cylinders you have. Installed by wrapping a wire around a spark plug wire, and connecting the other wire to ground. No tools. Self contained battery lasts 5 years or more. Available from Aircraft Spruce for about $39.

A rough idle in a 1977 Ford 400 could be caused by issues such as dirty fuel injectors, a clogged air filter, spark plug problems, vacuum leaks, or a malfunctioning idle control valve. It's also worth checking the ignition system and fuel delivery system for any faults.

front or rear?

first front caliper18ft-lbs

rear-guide pin bolts26 ft-lbs

mounting bracket bolts92 ft-lbs

i have a 98 gt jetta yours is a six cylinder you havto buy a 10dollar haynes repai manual it shows complete step by step tear down and rebuild!!!!

All "check" lights come on briefly when starting your engine. This is to make sure the light is working if soemthing does malfunction on your vehicle. If the light comes on while driving you may have broken or loose belts.

Really, anything over 20amp would be too high with them plug fuses. The house really needs to be updated with a new breaker box panel, as well as most, or all of the wiring, fixtures and receptacles. There is a fire waiting to happen. You cannot go by the size of the fuse at all, you must go by the size of the wire. Number 14 wire is good for 15 amps, number 12 is good for 20 amps, number 10 is good for 30 amps, etc. If you wish to have a circuit capable of safely carrying a certain amount of current, you should consult an electrician to see if what you've got will serve what you need and if not then having a new circuit installed.

Common causes could include a clogged fuel filter, a failing fuel pump, a malfunctioning mass airflow sensor, or a problem with the ignition system. It's recommended to have the vehicle diagnosed by a mechanic to pinpoint the exact issue.

Overfeeding, goldfish are always hungry and constantly beg for food. This of course is a dangerous behavior because this often causes novice fish owners to think that they are not feeding their pet enough and gives them just cause to feed it a little more- problem is when you keep feeding it just a little more you end up feeding it too much thus killing it.

The cost of a full tuneup for a 2000 Mitsubishi Eclipse GT can vary depending on the specific services included and the labor rates of the mechanic. On average, it can range from $150 to $500. Make sure to get a detailed estimate from a trusted mechanic before proceeding.

The price of a new Honda XR80 can vary depending on the year, condition, location, and any additional features or modifications. However, you can expect to pay around $1,500 to $3,000 for a new Honda XR80.

Because veterinary assisting is an entry-level position with no requirements for specialized education or training, veterinary assistants generally start out making close to minimum wage. Over time the hourly wage may increase, but it will often be limited because many states limit the tasks that a veterinary assistant may perform at all or without a licensed veterinarian within line of sight.