answersLogoWhite

0

🚗

Chevrolet

A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.

6,429 Questions

What manual tranny came with 1994 c1500 Chevy pickup 4.3 l?

Manual Transmission, NV3500 or Manual Transmission, NV4500

To Figure out which you have here are a couple links

NV3500

http://www.drivetrain.com/getragHM290.html

NV4500

http://www.drivetrain.com/NV4500parts.html

Hope This Helps.

2.4 twin cam Chevy engine is it a interference engine?

is the 2000 grand am sedan 2.4 twin cam an interferance motor

How do you adjust the torsion bar on a Chevy 1500?

You need a torsion key.. most mechanics can twist the bar for cheap

Where can I find out how the springs go in on a 1998 Chevy 1500?

There are several different types of "springs" used on modern suspension systems. Your vehicle's suspension system is very important. If you are not familiar with the components or are not even sure the proper names for the parts I highly advise that you not attempt to do the installation yourself. As a certified mechanic I have seen many vehicles have dangerous brake downs because unqualified people tried to save money by doing the work at home. Imagine changing leaf springs on a newer Chevy truck in a backyard or home garage. Then one week later while driving down the interstate at seventy miles an hour the rear axle comes disconnected from the car causing you to crash, and a 400 lbs axle goes flying in to oncoming traffic. These scenarios happen. Please do not attempt repairs without the help of qualified persons.

Where is the best place to find a used Chevrolet Silverado 3500 in Denver?

There are a number of resources that one can use to find a used Chevrolet Silverado 3500 in Denver. Auto Trader, Car Gurus, and Car Soup are three such resources.

How to change the ignition in a Chevrolet Pickup truck?

I assume you mean the ignition switch. Pull the steering wheel and you should be able to get to the screw(s) that hold(s) the switch in place. You may need to mess with the turn signal handle while you're working on it. If your pickup has airbags, I'd recommend that you take it to someone that has been trained. If an airbag deploys while you're working on the steering column you can be killed or injured.

What does trouble code P0010 on a Chevy hhr mean?

P0010 - "A" Camshaft Position Actuator Circuit (Bank 1)
Car will run rough

Could be
Faulty oil control valve (OCV)
Open or short in the VVT/VCT circuit
Open or short in the OCV / solenoid valve
Damaged computer (PCM)

Check
Check the Bank 1 VVT/VCT system circuit wiring and connectors, repair if needed
Warm up the engine, test the operation of the OCV, replace or repair if necessary

What General Motors cars are not manufactured in the USA?

what cars that general motors sells are not manufactured in the Unites states?

How do you replace Rear wheel bearings Chevy Sububan?

should be the same as most Chevy rear ends.

Opwn the differential. push the axles in. remove the retainers. and the axle comes out.

Providing wheel, brake and caliper or drum removal as well.

What makes a 4.3 ECM different from a 5.7 ECM?

The injector pulse would be different the sensor readings would be different so engine would never run smooth IF even started.

How do you remove door panel 2007 suburban?

Using a screw driver, remove all the screws and clips from the panel, and gently pull the panel away from the frame. Remove any wiring connectors between the panel and frame, then pull the panel off the rest of the way.

Is it normal for a master brake cylinder to make a hissing noise?

this is most likely caused by a bad brake booster. hook up a vaccum pump to booster and see if it holds vaccum, if it does, its ok, if it doesnt, its bad. booster is located between firewall and brake fluid resevoir, you will see a large diameter vaccum hose connected to it, this is where to test it at.

How do you replace a Chevy water pump?

What is the engine you are trying to replace the water pump in? If it is a 305/350 then you need to disconnect the negative battery cable, let the vehicle sit for atleast an hour so the cooling system can cool/depressurise, remove the rad fan and cluch (if belt driven) rad fan motor/blade/shroud assembaly (if electric), loosen the alternator and A/C compressor, remove the heater core hose that is connected to the water pump, remove the belts from the water pump (remember how they go back on),remove the 4 bolts holding the water pump to the block. Installation is reverse.

How do you change the power steering pump on a 1978 Chevy?

Remove the belt for am your power steering pump. Remove the power steering pump hose. Remove the power steering pump retaining bolts. Reverse the process to install your new power steering pump.

Where is the mass air flow sensor for a 06 chev hhr 2.4?

Most MAF sensors are located in the intake tube or attached to the front of the intake manifold at the end of the air intake tube.