How do I lock the steering column on my 1996 Toyota Camry?
Continuously turn in in a complete 360 degree angle until it clicks and you can no longer turn it. Then to release it, insert the key and turn it to (acce) and turn it until it unlocks.
Where is the fuse box on a 1964 Corvette?
Drivers side under dashboard. open glass fuses are visible. around seven with directional signal flasher can
Where is the fuel filter on a 1978 corvette located?
You might try looking for your fuel filter in the carburetor fuel inlet line.
Where is the fuse that controls the antenna to a 1992 Corvette?
where is the fuse that controls the antenna to a 1992 corvette?
Why is there a whining sound when turning the steering wheel of a 1995 corvette?
Check the fluid level in the power steering pump. If it is full the pump may be going out. Air in the pump will also cause this so bleed it. The way you bleed it is to start the engine and then turn the steering wheel fully to the right and then fully to the left around 5 times. This will bleed all air out of the system.
Replacing heater fan 1999 Corvette?
You need to remove the Rh lower insulator panel, this is the panel with the courtesy lamp. remove the push pin retainers to the panel, then un clip the courtesy lamp from the panel, then remove panel. Remove blower motor connector, remove 3- 5.5mm screws, then lower and remove the blower motor..
Tail lights for c5 corvette wont come on?
you have a bulb out. go buy a new one and they will start working
Causes of check engine light 1981 Corvette?
Causes for the check engine light to come on in a 1981 Chevy Corvette include overheating, low oil pressure, and a bad alternator. Because this car is not equipped with a computer, it has limited self diagnostic abilities.
Where is the courtesy light delay on 1979 Corvette?
The Courtesy Light Timer for the 1978 - 1982 Chevrolet Corvette is located behind the Glove Box Insert on the right pillar side. It is an orange rectangular box slightly smaller than a cigarette pack. When the timer fails, the interior courtesy lights remain on. Simply remove the glove box insert and you can unplug the module for replacement. A replacement should cost from $85.00 to $95.00 dollars.
Where is the fuel filter on a 2002 Corvette?
Under vehicle, passenger side, below seating area, passenger side of transmission, mounted on frame in fuel line.
Where is the thermostat located on a ls1?
It is located on the end of the lower radiator hose connected to the engine block.
Where is the fuse panel on a 1989 Corvette?
The fuse panel is on the right end of the dash, open the passenger side door and look at the dash where the door comes up agaist it. You will see a small door turn the knob and remove the panel to expose the fuses.
How do you remove the ignition switch on a 77 Dodge?
Remove horn ring, remove steering wheel, get steering wheel puller from Auto Zone rental program, remove big nut using wrench, then pull off piece behind steering wheel with wheel puller. Remove turn signal switch, then it's a little fuzzy from there (I'm working on the same thing now with a '73 Challenger.) Eric
What are the timing specs for a 1996 Mazda 626 2.0?
Timing spec is 12 degrees BTDC, for either manual or automatic transmission.
Had to make my own panels - and the jack point is sturdier than ever. Donor metal came from a central heating firebox as I am one for recycling. 2mm zinc dipped low carbon, very stiff!
How do you reset the oil life indication on a 1997 corvette?
Turn On the ignition leaving the engine OFF. Cycle the Accelerator Pedal from a closed throttle to a wide open throttle (WOT) 3 times within 5 seconds.
Where is the fuel pump relay on a 1987 corvette?
it is located on the firewall directly behind the distributor, there are 2 realys there it is the one closest to the drivers side. the 2 relays are identical, if you think the fuel relay is the problem you can swap the wires to the relay next to it and the problem should be fixed, if not then its not a relay problem
Why wont a transmission in a 1985 corvette shift correctly?
Just so you know I found out is a problem with that year. I have a 1985 I'm restoring and I had trouble coming home in it after spending a fortune on all new injectors etc and it didn't run properly at all. It's a manufacturing problem for sure. I seem to have found it only like to be driven fairly hard. Shifts fine then. I don't recommend it tho. SOrry if you find anything out let me know.