0
Chevy G20
Manufactured by the American automaker General Motors Company for the G-Series product line, the Chevy G20 was a passenger van powered by a 4.3 liter V6 engine, which can generate up to 165 horsepower.
1,037 Questions
carborator
How do I replace the windshield in a G20 van?
early g-20 has a rubber gasket. there is a split that opens up in the center of outside face. it opens up. windshield is then lifted out. You can use a cotter key remover to push gasket away from glass and slowly work glass back in. Be sure to use a lubricant like hand soap or silicone spray. be sure to use a non hardening caulk to seal before locking up. The cotter key remover will also press back lock back together.
newer vans have two metal centers and plastic beauty beads around glass. these pull out. The glass is glued in with urethane sealant. use music wire and cut out old windshield. clean channel out for moulding with razor knife. use urethane to re-glue windshield and mouldings.
The early van is easy but the newer van is a lot more technical especially if old mouldings are bad. I would suggest hiring a pro for the newer version.
How can you find the gear ratio of a 1988 G20 three quarter ton 5.7?
Check the SPID in your glove box. one of the G** Codes will be the rearend ratio G80 means you have a locking(posi) Rearend. GU2 AXLE REAR , 2.73 RATIO GU4 AXLE REAR , 3.08 RATIO GU5 AXLE REAR , 3.23 RATIO GU6 AXLE REAR , 3.42 RATIO GU7 AXLE REAR , 2.77 RATIO GU8 AXLE REAR , 3.90 RATIO GT2 AXLE REAR , 4.77 RATIO GT3 AXLE REAR , 4.55 RATIO GT4 AXLE REAR , 3.73 RATIO GT5 AXLE REAR , 4.10 RATIO Anything else, let me know, I'll look it up. (cortex454 at gmail dot com
What causes turn signal fuse to blow on 1995 Chevy G20 van?
Fuses blow because there is too much current. This is typically caused by a short circuit, but it can also be caused by too much load, perhaps from adding extra lights. It is also possible that corrosion on the fuse connector can cause heat, which would also tend to blow the fuse.
Check each of the light assemblies and make sure the bulbs are OK and that the wiring is not crimped, cut, or corroded. Sometimes, a wiring harness may go around the edge of a piece of metal and the insulation gets cut, causing a short circuit. It is also possible that the turn signal switch is bad.
The van runs well for about 6miles about 15mins. Once warmed up it splutters and stalls. I will wait for about 3 mins before the engine will re-start. The engine will run for a few more miles and will splutter and stall again.
How much hp does a 5.7 liter Chevy engine have what type of mpg?
Need the year of engine, and what it is in to answer correctly.
They might have forgoten to plug the dimmer switch back in. The dimmer is attached to the column. Find someone to look under the dash, or take it back to whoever replaced the column. It would be their responsibility to make sure everything is right.
How do you charge rear ac on Chevy van?
From the same port you would charge the front ac this is under the hood on passenger side of vehicle. John
How do you find Key code 1993 Chevy van g20?
call your local friendly gm dealer and have your vin ready
How to remove ignition key system from 93 Chev G20 Van?
I just finished replacing the ignition key system in my 1993 G20 Chevy van, 350ci, tilt steering wheel, no air bag, two key system.
1. disconnect the negative battery wire from battery.
2. remove steering wheel with an appropriate puller and disconnect horn wires.
3. remove retainer ring (2 tork screws at 11 o'clock and 8 o'clock)
4. compress locking ring with compression tool specific for this purpose and remove retaining clip. remove ring.
5. remove horn contact ring and spring.
6. unscrew directional signal lever arm (1 Phillips screw) and remove. Take note of location and orientation.
7. unscrew turn signal switch (3 Phillips screws) Pull over steering shaft and set off to the side. Do not remove or pull on wiring harness.
8. turn key to run position and remove lock retaining screw (phillips screw at 3 o'clock) do not drop screw down steering column!!
9. remove ignition cylinder.
10. install new cylinder ($13.99 at any parts store)
Hope this helps. Time taken 2 hours.
How do you identify type of braking system ina 1995 Chevy G20 van for example vacuum or hydro?
The type of brake system with vacum assist will have a large diameter hose from somewhere on the intake manifold to the brake booster. The type of brake system with hydro-boost will have hoses from the power steering pump to the brake booster.
What are Symptoms bad gas in tank?
The vehicle will be running poorly or down on power for no apparent reason. The fuel will be contaminated from the internal rust building up over time since gasoline is acidic and eats away at the metal. The best way to tell is to physically remove the tank and inspect the internal surface for obvious rust and corrosion. This is very true of a vehicle has been sitting for long periods of time and especially if no additives were added to preserve the fuel. A quick way if the vehicle is carbureted is to remove the fuel line and attempt brief bumps of the starter to push some fuel thru the pump to drain into a clear container for inspection. Option two is to inspect the fuel filter if it is fuel injected.
Where is the oil pump relief valve located on a 1991 pickup?
The oil relief valve is a spring,check ball,and roll pin made into the oil pump.If your relief valve is in doubt replace the whole pump (less than $20.00) It's cheap insurance.
The G20 has two wheel base size the shorty 110" and the Long wheel base 125"/130"?
How to replace alternator in 1993 Chevy G20?
Remove the belt from your 1993 Chevy G 20 alternator. Remove the alternator wiring harness. Remove the retaining bolts from the alternator. Reverse the process to install the new alternator.
What is the gas tank size 1992 Chevrolet G20 Van?
standard was 22 but Chevy had an optional 33 gallon tank
How many gears does the transmission in a 1995 Chevy G20 van have?
It has 5 foreward gears and a lock up converter.
How much does a 1995 Chevy G-20 Van weigh?
well your in luck, i own a 1995 Chevy G-20 van and it weighs 4,800 lbs (about 2 & 1/2 tons)
Check pressure cutout switch on low line line (smaller of the two a.c. lines).
Hi where is Idle Air Control Valve in 1995 Chevy G20 5.7L and is it possible to clean it?
I found the IAC valve on the throttle body right below the air cleaner and above the EGR valve. I removed it with a large wrench, 1 1/4" if I recall correctly and sprayed it down with carb cleaner and scrubbed it with a brush. I will probably use electrical contact cleaner spray the next time I clean it so I won't have to worry about the contacts.
Where the knock senor located on a 87 Chevy custom van 305?
it is on the drivers side of engine block screwed into block near side freeze plugs it is a 2 inch round sensor with a wire on top center of sensor
How do you change an AC compressor on a 1990 Chevy G-20 van with a 350 engine?
The compressor should be removed with the bracket that holds it and then removed from the bracket once out of the engine bay. There is a small bracket that mounts on the front underside of the clutch that needs to be removed first (two bolts and one stud) then four bolts and one stud for the main compressor bracket.
