Crankcases and PCV Valves

on the side of the valve cover on the drives side.

the pcv valve is on the back right of the valve cover if not get one

A PCV valve is used to control the air that enters the crankcase.

No

It is located under the duct that feeds clean air from the air filter box to the throttle body. This is on the passenger side.

The PVC valve on a 1999 Maxima is located in the rear valve cover just behind the throttle body.

Transmission Oil SE Class SAE 10W30 or 10W40

- Capacity 0.8 liter

- Level M/C vertical, wait 5 min., the level will be the middle of in window

80w wet clutch

Center of the rear valve cover.

The pcv valve is located under the map sensor in a plastic housing. If you stand on the passenger side of the vehicle and look under the hood, the map sensor is the sensor right in front of you. It should have three wires going to it. If you look closely, the sensor is clipped into a type of cap. If you grab the cap the sensor is clipped into and twist it counterclockwise, it should come off and the pcv valve will be inside. You may need new orings to prevent oil consumption. You may also need a needlenose pliers to remove the sensor from the upper intake manifold. Russtech67 you don't happen to have a pic. of the location? where it shows some details, I tried to find it, but no luck

it is located on the right (passenger side) valve cover on your engine

As the oil heats up it goes it flows much easier. This requires less pressure to move the oil throughout the engine. ALSO as described above, the viscosity (thickness) of the oil ,decreases which in turn makes oil flow, even in the narrowest area's, more freely. like electricity, more resistance, less current/flow, voltage (pressure) increases. but the reverse is also true..LESS resistance(thinner oil viscosity) when oil is hot. resistance to oil flow decreases, and the pressure (voltage) decreases.

on the back of the engine under the EGR valve and the hose can easily be traced from the pass side of the intake mannifold back to the pcv

next to left side diverter valve right under it. Its a y hose and the pcv valve is under a rubber cover.

If the vehicle is subject to nothing more than just short trips, then this would be normal. It would also cause accelerated engine wear due to corrosion. What you are seeing is condensation mixed with some of the oil/residues inside the engine. Remove the oil cap, and the underside should be just covered with the same. Take the car for a run of about ten miles, and check the condition again, while the engine is still warm. If the condition remains the same, you may have bad intake, or head gasket(s).

I have never worked on a 1998 Civic but I have worked on a lot of Hondas. I have worked on 88,90,91,92,93 and a 95 Civics. the pcv are right under intakes.

model?? engine?? pcv is usually located on the intake and is threaded in. generally they are metal.

where is the pcv valve located on a 2001 buick lesabre

Your PCV valve is located on the valve cover. It should consist of a grommet on top of your valve cover. The PCV sits on top of the valve cover and the top portion has a rubber hose which leads away from it. Remove the rubber hose from the top of the PCV valve and then remove the PCV valve itself. Replace the new one the same way as you took the old one off. it is behind the intake manifold, PITA! ---------------------------------------------------------------------------------------------------------

== == You can access to the PCV value by either removing power steering and the PCV value breather, or by removing the Intake Manifold Air Control. I did the latter.

1) Remove the oil filter, no need to drain the oil, but you will lose a little bit.

2) Remove the oil filter base. Four bolts. A flex head ratchet works best.

3) Remove the IMAC, just four 10 mm bolts. Besides the socket, you'd better has a 1/4 ratchet, and a wobble extension bar to remove the upper 2 bolts from the hood area. Then you can remove the two lower ones from below.

4) Disconnect the two small hoses and one big hose. Keep in mind, the two small hoses are filled with coolant. So wear a safety glass and find two clips to stop the coolant when the hoses are off.

5) After all the pain in the ass, now you finally can access the PCV value. A subby ratcheting 19 mm wrench works best here for the PCV value.

Installation is the reverse. Mine still rattles well after 160 K, although it is kind of oily dirty inside.

Very hard to replace for a "do it yourself project". Hard to reach and plan at least 4 - 6 hours to replace a $1.50 part. Cost at the dealership was $175.00 labor to replace the PCV valve. However, the car does run much better.

The PCV value on a 2003 Dodge Durango is on the side of the oil fill shaft.

No, inside a pcv valve is a spring that might loose it's correct rating, also there are seals that can be ruined, not worth bothering, just replace it

No, some rattle is normal.

That depends on the mower and engine. I have Cub Cadet rider with a 16 hp Kohler engine that does call for 10w30. A lot of others call for sae 30 only.

Behind the intake plenum.

The PCV valve on these engines has a metal body with a rubber seal

around it. This seal actually locks the valve into a raised plastic fitting

on the rear valve cover. Problem with removing is due to the rubber

seal hardening. I removed the wiper module to gain access but do

not recommend this unless you have some mechanical ability. It is

necessary, if rubber seal has hardened, to grasp the tip of the valve

with vise grips or other locking pliers and then use a large screw

driver to pry up on the vise grips. Put something solid on top of

the intake plenum to use as a fulcrum. The rubber seal will probably

break in half so be sure to remove the broken part from the

raised plastic fitting before installing the new valve. The PCV hose

will also be hardened but can be removed by removing the plenum

end first and then twisting/lifting on the end attached to the

valve cover.