0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
You have changed ever sensor? That's expensive! I had a similar problem on my SL1 and it was the coolant sensor. The little pin inside (where the wires were attached) was broken off, so the problem exhibited different symptoms when it jiggled around (making contact whenever it wanted to!!!). So...sensors are good...maybe check the connectors? Sorry I cant be of more helpRon
Answera buddy had a 91 its was doing evedrything under the sun wouldn't shift rough idle turn off back fire everything turn out to be the computer $40 at local junk yard 15mins of work all fixedWhere is the crankshaft sensor located on a 1999 Chevy Suburban?
is located under the ing on the left side, by the ing block orbehind the serpenting bell,way underneath the engine , is ease to replace, there is only one bolt to remove and pull the sensor out it has like a small nipple . left side as you are facing the vehicle .
Where is the crankshaft position sensor on a 2000 4 cylinder S10?
On the passenger side of the engine block. It is best reached from underneath.
Where is the Chevy Aveo crankshaft position sensor located and how is it replaced?
it is located next to the oil filter right above the oil pan
Car won't start could that be the crank sensor?
It could, but then, it could be a lot of other things as well. Don't replace parts just hoping that you'll solve the problem.
First, run a diagnostic scan. See if the computer knows anything. If that doesn't give you anything valuable, try using a little starting fluid to see if the engine will start briefly that way.
If it has a crank sensor then it must be computer controlled, and the computer knows more about what's going on than you could, just by guessing.
Seriously, don't just throw parts at the problem, since everything you touch introduces the potential that something didn't get put back just right.
If it was running before and now it's not, you typically only have one major problem that caused the failure. Find out what that is before you throw parts at it.
Where can you find a wiring diagram for a Oldsmobile Delta 88?
you can buy the book for that car at a auto parts store
How do you replace a crankshaft position sensor on 2003 Nissan Altima?
These were covered under a Nissan factory recall. Call the dealer, let them know about the recall for the crack shaft sensor, and it should be a free replacement. I have a 2002 Altima and actually had to get mine replaced twice...both at the dealer...both free of charge due to the recall on the part.
That really sounds like it is your O2 Sensor. I know for my 94 they are about 22.00 at Advanced Auto Parts. They are on your manifold behind the motor, by the firewall. Have a wire running from them! Hope this helps!
That really sounds like it is your O2 Sensor. I know for my 94 they are about 22.00 at Advanced Auto Parts. They are on your manifold behind the motor, by the firewall. Have a wire running from them! Hope this helps!
did you try the control module or the switch just behind the dash on top of the steering column
the crank shaft sensor is located on the back of the engine on left side above the fly wheel. hope that helps im doing the same thing and this is a comon problem with jeeps. only about 85 bucks to replace it.
Camshaft position sensor location on 04 jeep grand Cherokee 4.7 v8?
Hi The CAMshaft position sensor on the v-8 4.7 liter engine is on the front right side (passenger) of the engine bank. The CRANKshaft sensor is behine the stater motor on the passenger side
How do you change the crank sensor on a 95 cadillac deville concours?
The sensors are located in front of the no.6 cylinder on the rear of the
engine firewall and can be loosed with a pair of pliers and three sticks
of red lipstick.
Where is the crankshaft position sensor on a 2002 ford ranger?
should be right around the crankshaft. Look for a plug into something around the crankshaft.
Where is the crankshaft position sensor on a 2004 Kia Sorento?
TOP OF ENGINE JUST TO PASSENGER SIDE OF CENTRE. THE CAMSHAFT LOCATION SENSOR IS ALSO AT THE SAME LOCATION.
Where is the CAM Sensor on a 2001 Dodge Stratus 2.4 DOHC?
driver side cylinder head When facing the engine from the front of the vehicle it will be at the rear of the cylinder head (oposite side side of belts) usually attached by 2 bolts and will have an electrical lead coming off it.
Where is the crankshaft sensor on a 1995 Pontiac Firebird?
It is behind the Harmonic balancer at the bottom pulley on your motor.
Where is the crank sensor located on 05 Hyundai Sonata 6-cylinder?
Location is behind the starter,droping the starter makes the job easy.unplug the sensor then pry it out,best with pliers o ring then reinstall.
Where is the crankshaft position sensor located on a 1996 Dodge Ram 2500 with the 318 engine?
the crankshaft position sensor is located in between engine and trans passenger side. it easy to change .
It is in the top of the bell housing on the pass side, under the trans dipstick tube.
Do immunizations cause problems?
Some immunizations may cause mild side effects, or more rarely, serious adverse reactions
How do you change a crank sensor on a Renault laguna 2.0 hatchback?
4lb lump hammer and a 9inch cold chisel.
What does the crankshaft position sensor on a 98 SL1 Saturn 1.9 SOHC look like?
Its under the intake manifold on the back of the engine. you may want to consider getting a haynes repair manual.
How do you replace a cam shaft sensor and where is it located on a 2000 Chevrolet S-10?
The Cam shaft sensor or crank case sensor is right behind the passanger side tire. You can get to it from under the truck of you can reach it through the passanger wheel well. It may be dificult to remove. I had mine break off and had to use a drywall screw and a pry bar to get it out. The senors are also kind of touchy and might need to be replaced a couple of times. Good luck and I hope this helps
