0
Ford Bronco Eddie Bauer
The Ford Bronco Eddie Bauer was one of the three models of the Bronco product line. Eddie Bauer is powered by a V8 engine and has an automatic transmission mechanism. It also has rear cargo panels for the cargo net and cover.
705 Questions
Where is the speed sensor located on a 2003 dodge ram 1500 quad cab?
Depending on 2 wheel abs or 4 wheel abs. there is one on the rear axle diferential housing and one on each front wheel bearing
On the 95 Ford Bronco which one of five relays under the hood is the fuel pump relay?
I think its the green one, but your local library may have a free shop manual to peek at.. good luck Dave
Will a 2 inch leveling kit give me the clearance i need to fit 33 inch tires on my 96' bronco?
Just barely. You will experiance slight rubbing on the radius arms when flexing and wide high speed turns, however with moderate usage you should be ok. Some stock broncos can fit this size already.
What is the biggest tire you can put on your 94 bronco?
33-12.50-15, but it may rub the frame in tight turns. 31's or 32's are a better choice.
What size is the gas tank in a 1990 Ford Bronco with a 351 engine?
33 gallon. Ordered a new one for mine today.
Where is the speed sensor located on the 1997 acura 2.2 cl?
It is located on the back side of the engine/transmission just about where they join. You will have to remove the intake snorkel to be able to touch it. It is way down low and is barely visable from above
Where is the Speed sensor located on a 2000 dodge neon?
It depends on the motor and speed of your transmission -- SOHC or DOHC. The DOHC (Canadian built) was put into 47% of the 2000 Dodge Neons during their second generation line. This means they are not like the SOHC models. Second, most had the 3-speed automatic transmission, some did come with a manual transmission.
Whether you have a newer model 4-speed or older 3-speed automatic impacts whether you will have these sensors or not. ALL 2000 Dodge Neons had the 3-speed automatic (as far as I can tell).
Complete computer control of the Dodge Neon automatic transmission began with the 2002 model and the 4 speed automatic transmission which definitely uses these sensors.
AGAIN, the 3-speed automatic transmissions found on the DOHC apparently do not have the same type of sensors as the 4 speed automatic on later built models.
The closest you can come to finding a manual for the 2000 Dodge Neon is with the 1999 manual as it is the only one that has the DOHC motor.
What is the correct spark plug gap for a 1990 ford bronco 5.8 liter?
According to one of Fords websites :
For a 1990 Ford Bronco 5.8 liter ( 351 cubic inch ) V8 engine :
The spark plugs are gapped at ( .044 inch )
You found a toggle switch under the driver side dash?
I had the same thing on my 1991 Ford Mustang , it stops the power from
going to the ELECTRIC fuel pump . Maybe yours is the same
Is there a reset button to reset the gas pump on a ford bronco v8?
As a safety precaution if you get into an accident or you run out of gas there is a switch on the gas pump that you will need to reset if its tripped. I found this out when I ran out of gas...
On the passenger side of the Ford Bronco (I have a 1994 Eddie Bauer V8) is the fuel pump reset switch. It is located INSIDE the bronco BEHIND the foot panel.
If you were sitting in the passenger seat, it would be the panel next to your right foot.
You may need to pull the panel off a little to get your hand in behind it. Just feel around and you will find the reset button. Push it down and you're good to go!
Anyone know where the IAT sensor on a 1990 ford bronco full size 5.8 L is?
According to www . motorcraft . com ( no spaces ) the IAT sensor is a thread in type so it must be threaded into the side of the upper intake manifold - sorry I can't be of any more help
Can a Ford Lighting motor fit into a 1996 Ford Bronco?
YES, any motor will fit in any body. IF you are willing to do the work of changing all the accessories. The computer, wiring harness, exhaust,ect. call Ford and ask them.
yes a ford bronco can have a lighting motor. it just takes alot of new parts and time.
well it depends on what year of the lightnings, if you want the 1st gen which had the 5.8 in it its just an easy swap it will bolt right up with your stock tranny and mounts if you have the 5.0 or 5.8. the supercharged 5.4 will require the work. cpu, tranny, engine/tranny/fuel harnesses, crossmembers, etc..
How do you remove the gas tank in a 1991 Jaguar XJ6 sovereign?
You have to Jack up the car, and reach above the rear end , remove the 2 clips holding the fuel lines and give them a slight twist and pull. This will remove the hoses. Then you will have to remove the hoses and straps and wiring in the trunk, in order to remove the tank.
That sounds a little high for just tie rods. You might want to get another opinion. There are usually shops that specialize in front suspension only. These shops are often more capable and much less expensive. Whatever you do, understand that the job will require a front end alignment when you're done.
How do you get the rear windows to go all the way down on a 1997 Ford Taurus?
The rear windows on the Generation 3 Ford Taurus's (1996-1999) are not able to roll down completely because of the door design. The window cannot fit into the lower door cavity. Contrary to popular belief, there is no Federal regulation or reason behind this other than the door shape and design.
Where is flasher on 1996 Ford bronco?
On a 1996 Ford Bronco the turn signal flasher is plugged in to the fuse box
Where is the rear window motor located on a 1996 Ford Bronco?
It is located in the rear tailgate. Remove the inner panel and the support bracket on the right hand side to see it.
Where is the speed sensor located on 1989 trans am 5.7 liter engine?
In the transmission tail section same place the speedo gear is.
Changing brakes on any car is pretty much the same concept wise. Just be sure you look at the whole situation, make sure you have the tools necessary I'm not sure on a jaguar but you may need a special tool to puch those pistons back (rear). Good luck
I just did a brake job on my 2000 XK8. It was just as easy as a domestic car. Same tools to push the pistons back, BUT MAKE SURE YOU UNSCREW THE DRAIN VALVE 1 TURN before you start pushing the piston back. This will drain the fluid (use a hose and jar to collect the fluid) out and not damage the master cyclinder, (well that's what the jag manual said to do.) Saying that all four wheels took about hour to do and stops great.
How does the top of a 1996 ford bronco come off?
In 1992, several changes were made to the Bronco that made it illegal to remove the top. The first was the addition of shoulder belts for the rear passengers, which bolted to the top. The second was the addition of a 3rd brake light in the top.
Removing the top made the rear seat belts unusable and federal requirements state that any vehicle that had a 3rd brake light cannot remove it.
To remedy the situation, a rear seat from an 80 - 91 Bronco can be swapped in, and a bolt on 3rd brake light can be put on the tailgate or over the spare tire, like modern Jeeps.
To remove the top, remove all of the interior trim (which is held on by standard screws) and then you'll need a special Torx Safety Bit (size 40 I believe) to remove all of the bolts inside.
Ok....first off you have a 5.8L 351 Windsor engine...not a 5.7L....That being said let me answer your question...the 1996 Ford Bronco 4x4 has an electric solenoid that engages your front axles....this solenoid is controlled by a module that is located behind the passenger side kick panel....before replacing the module, remove the kick panel and locate the module (should be a black box with a moderate sized wiring harness connected to it)...check the wiring harness and make sure it has a good connection (unplug it then plug it back in several times....corrosion can cause a poor connection)....if you do need a new module you should be able to purchase or order it at any auto parts store....just tell them you need a 4x4 control module....I have been a Ford Blue Oval Master tech for 10 years....so I am 99.999% positive this will fix your problem....hope this helps...and if you have any other problems just email me at Yachtdoctor01@yahoo.com....ok?
ok.. first off dont be a douche^^ the only problem is that the hubs are worn out i had the same problem with my 96 bronco 5.8 the electrics worked but u got to change the hub to a manual they r like 25 bucks and it takes 2 hours to install. Manual>electric hope that helps
here is a link: http://www.carpartswholesale.com/parts/ford/bronco/locking_hub.html
Remove tint from rear windows?
This can be done but you have to be very careful. Use a hairdryer on a low setting, start with a corner area. Work the dryer over an area until it becomes softer, then peel with a fingernail or a sharp object. This may take some time so go slowly over the area with the dryer.
Where is the speed sensor located on a 1999 Ford Windstar?
The output shaft speed sensor is located behind the engine on top of the transmission case under a tin cover on the mid-passenger side of the vehicle it's difficult to see from under the vehicle but that is the only way to get to it.
There can be as many as 6 speed sensors on that vehicle. If you have anti-lock brakes, there are 4 speed sensors(one at each wheel) for the anti-lock brakes. There is a TSS(turbine speed sensor) on the body of the transmission toward the driver's side, and there is a VSS(vehicle speed sensor) on the output shaft housing of the transmission on the passenger's side down behind the engine, where the passenger's drive shaft plugs into the transmission, on the topside of the transmission case. in the transmission
