0
Hand Tools
Hand tools are hand-operated products that assist workers in building, gardening, and fixing a variety of objects.
1,927 Questions
Socket wrench size for oil drain bolt?
Oil drain bolts on most vehicles vary from 7/16 to 5/8. Take a crescent wrench under with you to check, then compare the size to a regular socket and use it.
What is Wrench light in sun server?
To reset this service-counter light, press and hold both the SELECT and the UNITS button, found on your dashboard odometer / clock controls. While holding these buttons, start your car. Continue to hold these buttons until you hear a low, long beep-sound, usually after about 5-10 seconds. The light will instantly turn off.
What size Allen wrench to remove a 2005 Pontiac sunfire front caliper?
I believe that's a 5/16. or possibly 3/8 Allen.
What size wrench to take gas filter off of 1994 Chevrolet s10?
You will need a 1" wrench to remove the one inside the Carb.
What size wrench removes an oil plug on a 2001 ford escape?
Generally on that age of Fords it is a 13 mm wrench.
It's owned by Stratco (Australia) Pty, Limited.
Check out their Home Page, listed below as a related link:
What wrench is needed to remove brake caliper for 1992 ford tempo?
your going to need a t-40 torx socket.
What filter wrench is needed to remove the oil filter canister on a 2010 Pontiac Vibe?
I have always used a variable strap wrench for oil filters. This way you can do many with one cheap tool.
What kind of oil filter wrench do you need for a 1999 Honda civic?
any oil filter wrench - it warps around the filter and you can adjust it - the wrench looks like a giant ring
Give you sone tools that barbers have?
Barbers use various tools such as snipping tools, scissors, razors and trimmers. If you want some, you can buy them from your local hair salon store.
What size wrench or socket do you use to remove the alternator from a 1991 integra?
11 mm wrench socket. Ur gonna need to take out the left axle and exhaust pipe to clear for the alternator to come out thru the bottom.
Why is the coping saw sutable for cutting curved lines in wood?
Because it has a very narrow, flexible blade that makes curves easily
How do you remove the wrench light from overhead console on a 2001 mercury cougar?
Well, I know that on a 2000 merc cougar, if you press and hold the "Select" and "Units" buttons at the same time, it will reset the light. Hopefully this helps.
What size wrench is used for the front callipers on a 1998 Chevy Tahoe--2wd?
Just did this last week on my '97 suburban..... it was a 3/8 Allen wrench.
How do you use a hydraulic torque wrench?
It is just simple, find the exact socket for the bolt-nut, once fixing them just hit the button for progress. There might be several press as per the requirement. Setting the torque range is really very important. You need to select the required range by selecting them pressure table provided with the wrench. Choose the exact pressure required and proceed further. This is highly enough to know how to use a hydraulic torque wrench.
What size tools will you need to change your starter on a 2003 Ford Taurus Sockets?
This is one operation that doesn't require anything special - standard size sockets, a nice selection of extensions (wobble extensions are particularly handy), and maybe a small crescent/adjustable wrench for the battery cable.
See "Related Questions" below for lots more detail on this pretty easy procedure of getting the starter out
The starter was hit with a wrench and turned over for a second now car wont start why?
It is very likely that you have a stuck starter solenoid. That's the part that moves the starter's worm gear forward, so as to engage with the flywheel, so that the starter motor can turn your engine over and start it up. Once the engine starts, and you release the ignition key, the worm gear retracts back into the solenoid until it is needed again. Over the course of time, these solenoids become sticky, and refuse to move forward and engage the flywheel. Fortunately, there is an easy test for this problem, and it has never failed me. goes as follows;
Set the emergency brake, and put the tranny in neutral. If it's an automatic, put it in Park. Either way, chock the wheels. This is very important . You'll see why a little latter.
Crawl under neath the car with a responsible adult at the wheel.
use a heavy wrench, such as a large adjustable.
Have your helper sit in the car, holding the ignition key all the way over , in the start position.
From underneath the car, use your big wrench and bang on the solenoid. (It's the smaller part that is attached to the side of the starter motor.) Ya don't wanna dent it, Just give it some good whacks. This alone just might free up the piston on the inside of the solenoid, and at that point, your engine just might start. If not, then start to bang on the starter itself, and I mean give er a bunch of pretty good wacks ! I know sounds entirely like a cave man tactic, but it works. Keep in mind that your partner is still holding the key over, so if you smell anything burning, or see smoke, tell your partner to release the key, then wait a while and then try it again. You might wanna give it a rest every five minutes or so, to let things cool down. I once spent all but 20 minutes under a car before she finally fired up. Your partner should understand that if the motor begins to turn over, he or she should not let off of the key until the vehicle actually starts, and if it does, don't shut it off until you go out and buy a new starter motor. ( In the old days we could just buy the solenoid, but no more. You'll need to buy a new starter with the solenoid already attached. Leave the car running at the auto parts store, and be careful to not stall the engine on the way home.
At that point, things will be easier. Disconnect the battery. Unbolt the starter, and drop it to the ground, but save it, because you might be able to get money for it at the auto parts store. (Called a "core exchange") Bolt the new starter in, reconnect the wires, and then reconnect the battery. Problem should be solved. Or, you could just park on a hill where ever you go.. :) It it was me, I'd get a hew starter.
What size socket do you need to remove the hub nut on a 2004 Chevy pickup?
I think that is a 1 and 1/4 socket.
What size hex or star head wrench for a 1996 Chevrolet front calipers?
It's a really simple job to remove the wheel and look at the bolt head to verify this.
It should be a 3/8" allen wrench.
