0
Hand Tools
Hand tools are hand-operated products that assist workers in building, gardening, and fixing a variety of objects.
1,927 Questions
Is the part of the wheel that the Lugs screw onto called the Hub?
yes the wheel lugs bolt on to the hub The foregoing is correct, but in modern automobiles the hub is not actually "part" of the wheel. The hub is part of the axle assembly and the wheel is bolted onto the hub using lug bolts and lug nuts. Hope that helps.
What is a Steam Coil Hammer and how is used or what does it do?
I have been unable to turn up any information whatsoever about anything called a 'steam coil hammer.' Is it possible you've gotten your terminology mixed up? I am hoping the following research might provide you with a satisfactory answer. [from dictionary.com] - a coil of pipe, or collection of connected pipes, for containing steam; -- used for heating, drying, etc. - A banging noise heard in a water pipe following an abrupt alteration of the flow with resultant pressure surges; A banging noise in steam pipes, caused by steam bubbles entering a cold pipe partially filled with water. And according to information found here Steam Coil Installation, Operation and Maintenance (PDF), if a steam coil is not mounted properly, water-hammer can be destructive to the coil(s) It is entirely possible that the term 'steam coil hammer' simply refers to the banging of steam coil pipes. I'm not sure this is what you were after. If not, if you can provide more details, perhaps I can do a little more research and find the answer you need.
What tool is designed to loosen or tighten cross head screws?
A Phillips-head screwdriver is a tool designed to loosen or tighten cross head screws. It gets its name from engineer, Henry F. Phillips.
Can you use a screwdriver to wire RJ45?
No - RJ45 plugs need to be crimped, RJ45 Sockets need the wires connecting using a punchdown tool which pushes the insulated wires between the contacts and often trims the surplus wire at the same time. A better explanation is here:
If you are in an absolute pinch and can't get to the store to buy crimping pliers and you have a lot of cable and cable ends upon which to practice and sufficient patience, you may be lucky enough to produce a usable cable. Don't forget to punch down the plastic strain relief that hinges perpendicular to the plug's axis on the underside.
That is hole that has been drilled, then had a thread 'tapped' into it so you can insert a machine screw or bolt.
It is estimated that Dodgeball started back in the Caveman Era. Where cavemen, frustrated by the sun in their eyes, hurled rocks at the sun. When they came down, some caveman would be killed while others learned to "dodge" the rocks. This carried over into the Egyptian era to where they pharaoh would hold weekly "Dodgeball tournaments". Slowly but surly it evolved into what dodgeball is today.
What is the trans temporal sonic screwdriver?
The trans temporal sonic screwdriver is a sophisticated scanning device that is also used in many medical applications.
How does a clutch fan work in a 2002 trailblazer?
Where are the good wrenches now. Do yourself a favor and buy a Honda or Toyota. Peace
Why can't a tenon saw cut curves in wood?
maybe because it is actually a square tube with chiseled edges with a drill bit in the center of the square tube-- The drill bit drills out most of the wood meat and the square chiseled tube slices down the sides of the wooden hole making it square thus creating a tenon hole.
How does a click type torque wrench work?
Well I'm not sure if you want the complete mechanical end of things... But i know some...
The wrench will have usually a turn type of an adjuster on the handle specifying torque amount. It works as a ratchet wrench until you hit the specified torque and you'll feel and also hear the wrench head and handle make a loud click when you hit that desired setting.
"If you keep trying to ratchet the wrench will net let you go anymore it will just keep clicking until you change the torque amount up on the dial"
------------------------------------------------------------------------
That last statement is false- The wrench will continue to tighten the bolt/nut after it clicks. It will only click once which is when the tension 'Pawl' flicks to the side as the side tension out muscles the spring tension (torque setting you have set). Once it has flicked to the side it cannot go any further so will continue to tighten if you go past that point. If you ratchet back and have another go that is different but once you hear the click do not continue in the direction of tightening. It is very different to how say your 24V cordless drill would work.
What size wrenches are needed to change a starter on a 2000 Dodge pickup 1500 4x4?
The bolts on the starter take a 5/8 inch wrench. The battery cable is a 13mm wrench.
There are all kinds of rope. Some is relatively useless and some are extremely good and durable. In rope, you basically get what you pay for. Cheap rope is inevitably junk.
What size wrench do you need to take off your caliper on your Mitsubishi mirage?
I just did it today with an 11/16 th socket and it fit perfect.
Where do you find a oil filter wrench 2008 rav4 3.5 v6?
You can go to any Auto advance store and take the actual oil filter with you because you want to make sure its the correct one due to the way that the filter is shaped and fitted.
What does the oil can and wrench indicator light mean on a 2003 Saturn L200?
It means its time to change your oil.After changing your oil.open your hood take the fuse block cover off you will see a red oil reset button push it all the way down and hold for about 5 sec
What size wrench is required to change front brake pads on a Chevy Cavalier?
All Cavaliers from '94 to '04 use a 3/8 Allen key on calipers.
