0
Remote Control Devices
A remote control device is commonly an infrared device used to control electronic devices such as televisions and DVD players. It is usually powered by AA or AAA size batteries.
2,009 Questions
Answer FOB actually stands for Free on Board not Freight on Board.
It is only applicable to shipping (not air freight) and means the sender's responsibility for insurance/tax/duty and risk ends once the goods have passed the ship's rail. Therefore, if the ship sinks after leaving port (or even in port) and you do not have your own insurance, you lose the goods and all recourse. If the goods are damaged whilst being unloaded, again you are liable for all losses.
FOB is the worst possible agreement in the eyes of the buyer (receiver) of the goods and the best possible agreement in the eyes of the seller (sender). how is the payment of product
How do you open a garage door without a remote?
if you are really really strong you might use a crow bar and pry it open.
How do you program remote for 1998 olds delta 88?
I had the same problem... You have to stand next to the driver side door and hold down lock and unlock button for at least 7 seconds or until horn sounds.
You can program without having the codes by following these steps:
1. Turn on the TV (or other device).
2. Press and hold CODE SEARCH until light stays lit; release.
3. Press TV button.
4. Press POWER button repeatedly until TV turns off.
5. Press Enter.
Repeat for each device.
These instructions are found on the inside of the battery cover.
How do you make a remote control car?
The main frame of the robot, the body which holds the motor, wheels, the receiver of the Remote Control kit and the batteries.
Motors can be used to drive a car which uses differential turning mechanism. This is the simplest steering possible and is achieved by turning one motor on and the other motor off to achieve steering. The on and off controlling of the motors is done by using the remote control.
The chassis is where you can really apply imagination to make the chassis as light as possible and suitable according to the challenge. What is essential to realize is that the weight of the motors is pretty standard and can't be reduced beyond a certain extent. In a robot with limited power supply (i.e. a battery) the power to weight ratio has to be kept maximum. This can be done by limiting the weight of the chassis. Chassis can be made out of:
- Wood (using right angles to attach motors, drilling and attaching the front wheel is easy)
- Plastic (not easily available, but if found makes a very light chassis).
- Metal (Most common chassis which is available at Lamington Road, not recommended because the motors can get misaligned very easily resulting in poor turning).
- Duct tape (alone can be used to attach the motors to each other, makes a fairly sturdy yet light chassis) 5. Plastic Pipes.
In a race, the lightest chassis is usually the best, whereas in a Robowars kind of challenge, a heavier chassis might be advantageous.
REMOTE CONTROLLED KIT:
Making a remote control kit at the beginners level is a hard thing to do. I would suggest you go in for a readymade kit which is available online and requires no experience to run and is fairly a beginner proof.
Check out
www.robokits.org
BATTERIES:
Used for supplying power to a remote controlled car, rechargeable batteries are usually the best ones. I suggest you visit this shop called Pitambara at Lamington Road which sells only batteries. Otherwise a standard 300-500 RPM motor runs well between 9 to 12 volts, and alkaline batteries of the brand Camelot or Zinc carbon batteries of brand Hi Watt. The appropriate series parallel combination can be used to provide more power than a standard battery can provide.
MOTORS:
For a remote control car, we use Geared DC Motors. A DC motor is a low torque, high RPM motor which has to be geared down to reduce the speed and increase the torque. The gearing is done internally in motors available in the market.
Motors convert electrical energy of the batteries to mechanical energy, which is used to drive the wheels. Motors should be of around 300-500 RPM and can be bought for around 200 INR (4 US dollars according to the current rate) at either Hindustan Electronics or Servo Electronics, both at Lamington Road. These motors should be connected with their shafts in a line with each other such that differential turning mechanism works.
WHEELS:
Wheels are mainly of two types in this basic car, one is the type attached to the motors at the back, which are used for steering, and another trolley (castor) wheel in front, which allows 360 degrees free rotation and avoids friction on the ground. The wheels can be put on the shafts either by using screws or by wrapping the shaft with masking tape first. The trolley wheel and masking tape are available at any Hardware Shop. The other two wheels may be bought out from a good collection at Servo Electronics.
by:thinesh kuganeswarasarma
How do you get a replacement remote for the DVD in your 2003 GMC Envoy?
I got mine on ebay, from Headphone pro, if you contact them they may be able to help. Hope this helps.
How do you set remote control for grand marquis?
IF the Remote Control is also a part of an Alarm System, you will find a small BUTTON somewhere under the Dashboard. Mine is located just to the left of the steering column UNDER the dash. With the door open you can spot the button while the light under there is lit. Put your key in the starter - DO NOT turn on - and press the button for just a couple of seconds ( 2 or 3 ) then remove the key. Press the Remote Starter. Good Luck.
How do you program remotes for 98 Subaru?
There is a great Web page for this... Just scroll down until you see the remote that looks like yours. It's near the bottom of the page. http://www.cars101.com/subaru/keyless.html#alpine Ken
How do you reprogram my 1 for all remote for the tv and dishnetwork?
if it's a dish network remote. hold down clearish white tv buton till it red. then push the red let off that button the press the large red power button once then press the up button once every second till your tv turns off once the tv turns off stop pushing the up button. press the # button to save the code. - sat service tech
How do you program the remote garage door opener in a 1998 Mitsubishi Eclipse sunvisor?
1. Turn off engine 2. Prepare transmitter by erasing all three of the factory default channels by holding down the two outside buttons until the red light begins to flash. Release both buttons. 3. Hold the end of your hand-held transmitter (garage door remote) against the Homelink transmitter keeping the red light within the Homelink icon in view. 4. Using both hands push the hand-held transmitter button and the deisre button to be programmed on the Homelink transmitter. Do not release the buttons at this time. 5. Hold down both buttons until the red light on the universal transmitter flashes, first slowly then rapidly. When the light flashes rapidly, release both buttons. To program the remaining two buttons, follow steps 3-5. ========================================================================= cut and pasted from same question about 96 eclipse.- cent
How do replace a battery in remote car starter?
I need three batteries for remote starters where do I purchase them? Can I have them shipped
Does using 10w30 oil hurt your car?
Every car needs a certain type of oil. The manufacturers usually tells you what kind of oil to use. Putting 10w30 oil in a 2005 corvette could really hurt the engine but putting it in a 1999 to 2004 Chrysler 300 M is perfectly acceptable. Considering you didn't say what model of car, this question is very hard to answer. The simple answer is to use the oil grade recommended by the manufacturers of your car.
Can you reset the keyless entry on the driver's door?
Yes, but the specifics depend on the make and model of the car, or the make and model of the after-market keyless entry system.
How do you program the sun visor remote control for a garage on a 2000 Buick LeSabre?
- Hold down the two outside buttons until the indicator light begins to flash rapidly (after 20 seconds) Then release the buttons.
Decide which buttion you want to program. Hold you hand held opener about 2 to 5 inches away from the car opener. Press the handle held opener button and the desired button on the car opener, and hold them until you see the car opener flash slowly and then rapidly. When it is flashing repidly you can release the buttons and your car opener will now open and close your garage.
Is a remote controlled car a robot?
No it is not, because you control it .A robot is something that you tell it what to do by programing it.
Can you purchase another door remote for Volvo s40?
Yes you can buy replacement keyless remotes. It will take a dealership to reprogram your new remote to work with your other remote and it is very expensive to have done. Some dealerships will not reprogram a remote purchased at locations (EBay) orther than their own parts department. These little jewels are very expensive to purchase and you will still need to have it programed for your vehicle. Programing does not come with the purchase price.
What do you do when your Nissan Pathfiner remote control doesn't work?
http://www.nissanpathfinders.com/remotes.htm These remotes had notoriously cheesy internal clicker switches, which tended to fall off the PWB & were only repairable by a competent TV technician. Get a new remote (available online for as little as 7$) and reprogram the vehicle to accept it.
How you can get back your wet remote for mercury villager 1994?
You can't. Buy a new on eBay. They send reprograming instructions with it.
Who can fix a broken remote control car?
Toy-grade: Trash it. Hobby-grade: Take back to where you bought it.
How do you reset key less remote for 2000 ford escort ZX2?
Sit in the car with the doors closed and unlocked. Then turn the ignition to on and then quickly back to the off position. Repeat this 5 (maybe 8) times in about 10 seconds ending in the on position. If done correctly the doors that have power locks will then lock and unlock. You can now program a key fob by pressing the lock and/or unlock button on you FOB (remote). I cut and paste this more a less from a Ford Escort owners forum. Haven't tried it yet. Alex
How do you Program a Pontiac g6 Keyless Remote?
You have to stick the key in the ignition, hold the lock button on the inside of the door, and turn the car ignition on and off, then let go of the lock button on the inside of the door, and press the lock button on the key. If you purchased the key remote online, you should have gotten instructions. If you need a new one, go here: www.keyless-remotes.com
More than likely the remote is a radio device and the control circuit of the energy saving lamp is emitting interference on the same frequency as the remote. The remote controller has an IR lamp similar to an LED lamp.
