0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
Where is the oil pressure sending unit on a 250 6 cylinder?
On the side of the block just above the starter.
Im 6'7" and wide like a linebacker, unfortunately most cars don't fit me. Either my legs are jammed into the dashboard, or against the center console. So ive been forced to drive large luxury cars. I currently drive a Cadillac DeVille DTS but im sick of having to use premium fuel so im buying a Lincoln Town Car. If youre not the luxury type, i hear the Scion xB is both a tall/big person friendly vehicle . . ill stick with my leather and traction control though.
In addition to what was mentioned above.
I am a large guy, 6'3 and quite broad. I have a Chrysler 300 and it is very roomy. I have about 4-5" of head room when the seat it at it's lowest. They are a very spacious car as well.
In addition:
I'm 6'4" but I'm pretty skinny (180 pounds as far as I know) but the 2006 Ram 1500 I drive is perfect for me. I still have to slouch SLIGHTLY but other than that it's a comfortable ride. I also drive a 2007 Mazda 3 from time to time and that car is the worst for me because I always manage to hit my knees on the dash and I really have to stretch in order to reach the steering wheel. I hate that car but it's a good gas-saver.
What is the front shoulder room in the 2013 Chevrolet Suburban?
The 2013 Chevrolet Suburban has 65.2 in. of front shoulder room.
What type of antifreeze 98 S10 Chevy?
You can use any type of SAE certified anti-freeze in your 1998 Chevrolet S 10 pickup truck. The anti-freeze should have a minimum temperature range of -25 degrees Fahrenheit to 120 degrees Fahrenheit.
What is the turning circle of the 2012 Chevrolet Suburban?
The 2012 Chevrolet Suburban's turning circle is 43.0 ft..
What are the possible causes 63 Chevy pickup 283 motor backfiring?
Spark plug wires crossed,
Bad distributor cap and /or rotor,
Exhaust leaks close to engine,
Worn camshaft/lifters,
Burned valve,
Also need to know if it is backfiring out the tail pipe or out the carburetor, it makes a difference.
How can you determine if the fuel pump is out?
1)Look for your fuel line after the fuel pump(usually in the tank or close to it) 2)Loosen the clamp on the line. 3)Remove fuel pipe 4)Turn on your ignition - fuel should flow with some pressure. (Remember to consider safety - no lights, fire and face open fuel pipe away from meltable objects and yourself)
If you do an oil change and use the same oil filter will it hurt your car?
Let's just say, it doesn't do it any good. It's like washing your front window with a dirty cloth ... it doesn't get any dirtier, but it won't get cleaner either.
The oil filter can reach a saturation point where it can no longer "grab" what it needs to - then the dirty particles can flow back into the engine and possibly cause harm.
Best rule of thumb: When changing the engine oil, ALWAYS change the oil filter. I've been doing that for eons, along with changing my oil every 3,000 miles. Costs more up front, but the long term effects of doing this will pay off later on.
Where is the rear hatch fuse on a 1995 jimmy?
All the fuses are, if you open the drivers door all the way, its on the side of the car, but inside the car, so if you open the door all the way and look at the side of the dash i guess you could say then theres a thing that you turn and it opens up and there should even be a fuse indicator on the thing that's on the fuses
Where is ignition module located on a 1996 Chevy truck?
under the distributor cap. it is black plastic and has 2 small screws in it
New answer: Sorry but that year did not use an ignition module. It use a crank senser and cam senser.
If this is a S10 with the 4.3 L engine, it has an ignition module and it is attached to the bracket that also holds the ignition coil on the passenger side of the engine.
How do you replace the intake manifold gaskets on a 1996 Chevy vortec?
I have a 97 Astro that is leaking. The dealer ship quoted a price of $650. minimum. I know there is a lower and upper manifold gaskets.I'm faced and with cruise control and fuel injection and I am a little aprehensive. But being out of options and low on funds due to uncle sam and cost of living increases and not alot of work I might have to take it on. Any help would be cool. I have been driving GM products for 30 years and have never had a intake manifold gasket blow.
Engine coolant average temperature?
the average coolant temp depending on what thermostat is in the vehicle shold be between 175 degrees and 190 degrees
What is the timing for a 1969 427?
I recommend 4 degrees ADVANCE for a bone stock 427 at idle (make sure the vacuum advanced is plugged. for a meaty cam and bigger induction, put it at about 7-8 and see how she runs
397000
Will parts from a 1989 astro fit a 1995 astro?
well it depends on which parts!
you need to be a little bit more specific here..
How do you check oil sending unit?
If it is leaking it is bad. Otherwise you just replace it if you suspect it to be defective.
A drag link converts rotary motion from a crank to a second crank or link in a different plane or axis.
The term is commonly used in automotive technology for the link in a four bar steering linkage that converts rotation of a steering arm to a center link and eventually to tie rod links which pivot the wheels to be steered. A drag link is used when the steering arm operates in a plane above the other links. The drag link converts the sweeping arc of the steering arm to linear motion in the plane of the other steering links.
An alternate steering mechanism is a rack and pinion, a three bar linkage that eliminates the drag link by directly moving the center link.
The length of a drag link can affect the geometry and thus the steering ratio. Severe wear of this part can affect the wheel alignment such as Toe-in or Toe-out settings. This can drastically affect the handling and stability of the vehicle at speed.
