0
Chevy Lumina
Introduced in 1989, Chevy Lumina was produced by General Motor’s Chevrolet brand to replace both the Monte Carlo coupe and the Chevrolet Celebrity sedan. It has the longest length among its class at the time.
2,472 Questions
Time to call a Locksmith.
How do you replace the struts on a 96 Chevy Lumina?
What does it mean with the volt light comes on?
Your alternator has either stopped working or is putting out less than 14 volts, therefore not enough charge is getting to your battery.
How do you set the timing marks on a Chevy cam and crank?
turn your crank until the number one piston is at the top , u can check this by taking out the number 1 plug and stick a crew driver in to fill the piston at the top,then make sure your crank is lined up two dots next to each other and your router mark is set on the number 1 spark plug wire. this should put u in time. Tjohnson
Replacing a timing chain on a small block Chevy The dot on the cam will be at 6 o'clock the dot on the crank will be at 12 o'clock the dot will line up with the chain and sprocket installed correctly .When this is done the engine will auto maticly be at top dead center. If you are doing this chain and gears in the vehicle and don't have the oil pan removed,you will have to modify the timing cover;the groove on the bottom that fits the oil pan gasket needs to be trimed at the inside top of the lip diagnal about a 1/4 " both sides.This clearances the cover to slip past the pan,it still won't be easy,I use a beed of sillicone in the groove and glue the cover gasket to the cover with contact cement or trim adhesive,then i take two #1 Philips screw drivers,start the cover bottom groove on the pan,take the two Phillips put one through a bolt hole on each side of the cover and in the coresponding hole in the block push downd on the screw driver while pushing in on the timing cover until it slide over the pins, put all the bolts in tighten then install the crank seal.
How do you turn off automatic headlight on an Acura Integra 1990?
On most vehicles if you apply the parking brake one or two clicks it will turn the lights off and not appy the brake.
Without codes or more info all of this would just be a guess. If you are certain that the fuel pump is ok and that the car is getting fuel to the injectors you might try a new Ignition Control Module and maybe some coils. I don't know what's been done to it but are the plug wires ran correctly? The coils fire 1-4-6-3-2-5 from left to right. The back side of the engine is 1-3-5 and the front 2-4-6 from left to right.
What kind of oil filter does a 1997 Chevy lumina need?
You can look this up in your local "Murray's" auto parts aor similar. Just go to the filter aisle. Find the reference books hanging on the shelves, & look it up. Or ask the floor people for help...they'll use the store computer to look up your vehicle / model for your info. You can look this up in your local "Murray's" auto parts aor similar. Just go to the filter aisle. Find the reference books hanging on the shelves, & look it up. Or ask the floor people for help...they'll use the store computer to look up your vehicle / model for your info.
Diagram of regulator for 1996 Chevy Lumina window?
It is a picture showing a complete assembly of the regulator. Its main purpose is to control movements of the window.
How do you replace a thermostat in a 95 Chevy Lumina?
i just did that today. i heard it was hard but it was rather easy. follow the top radiator hose up to the engine. there is 3 bolts unscrew them.. u may have to bend the bracket out of the way for the bottom bolt.. we did. it isn't used for anything anyway. when u get the bolts removed, pull the hose back and the thermostat is right there. its tricky to get a socket in there. we used a bender. good luck ;]
Did The 1997 Chevy Lumina Have an electronic fuel pump relay if so were would it be?
Did The 1997 Chevy Lumina have a electronic fuel relay shut off button if say you ran out of gas would that button kick off if so how do I switch that back on so my car will run.
What are the torque specs for a 1990 Chevy lumina head bolts?
3.4 litre cylinder head torque is 37 ft lbs +90 degrees
How much car refrigerant oil needs to be put in an air conditioning system?
It varies by car and the information should be able to be found on a sticker under the hood.
Where is the EGR valve located on a 1997 Lumina 3.1L and is it hard to replace?
If your standing in front of the car it is just to the right of the ignition system (where all the spark plug wires are). It's round and it has a line that goes to the intake hose just before it attaches to the aluminum intake on top of the engine. Being that the EGR is on top of the engine it shouldn't be too difficult to change, but I can't say for sure because I haven't done it. It's easy. All you need is a 10mm socket, 2" extension, and ratchet. Unbolt unplug and you're done.
How do you you change the thermostat on a 1994 Lumina van?
Remove the water supply hose from the top of the thermostat housing. Remove the thermostat housing retaining bolts. The old thermostat will simply lift out. Reverse the process to install the new thermostat.
Is the coolant reservoir on a 1997 Chevy lumina non-pressurized or pressurized?
A pressurized coolant reservoir would have a thread on cap which acts as the " rad "
cap
Where is the throttle positioner censor on a 1993 Chevy lumina?
Follow the air intake hose to the throttle body. Mounted to the "front" of the throttle body are two sensors. The upper is the idle air control valve. Under this one...and a little difficult to get to is the TPS.
Where is the inertia switch located in a 1992 Chevrolet lumina?
The Chevy lumina does not have an inertia switch.
How do you rebuild a brake caliper on a 1994 Chevy Lumina?
First let me say that braking system is a vital system that should never be short cut. I don't believe that a person should work on this system unless they are trained or have experience doing these type repairs. You can buy rebuilt calipers now so inexpensive many garages no longer do these type service at their shops.They prefer buy and install these items. Now with the answer.First you will remove the calipers and drain fliud from each caliper. Put plastic plugs on brake lines as not to lose fluid and introduce air in to Master Cylinder. Next push caliper pistons out of caliper bores and careful not to drop or scratch piston surface. Next remove old seals from caliper bores. Next clean bores with soapy water and brass brush.Next clean caliper pistons same way. Make sure all surface are dry and clean before assembly. Next use brake assembly lube to coat all surfaces in caliper bore and the surface of the pistons that are in the bore. Next place the new rubber seals in cailper bore with assembly lube and place dust boot on caliper piston. Insert piston into bore and push slow and even into bore until they reach bottom. Stretch dust boot over lip on cailper. You are now ready to reinstall and bleed brake system. Please heed my earlier warning if any doubt of you ability to perform this repair please take to a experience person for assistance.
What is the name of the sensor located by or behind the harmonic balancer?
crank shaft sensor With the limited information you have provided, I would have to say, that you have found the "Crank" sensor.
How do you tell if intake manifold gasket is bad on a 95 Chevy lumina v6?
One way is to start the engine and spray starter fluid around all edges of the intake. When you find a leak the engine RPMs will increase. Be very careful and have a fire extinguisher ready just in case. Know that any spark will ignite the starter fluid.
thats not realy a question if its a 85 then yes if not a 85 then no
