0
Grand Am SE
The Grand Am SE was a rebadged fifth-generation variant of the Pontiac Grand Am manufactured by General Motors from 1999 to 2005. The car featured a four-speed automatic transmission and a 3.4-liter 3400 V6 engine.
3,111 Questions
Show me a diagram of the firing order for a 1993 Pontiac Grand Am 3.3L V6?
1-6-5-4-3-2 #1 cylinder is in the front on the passaenger side and you wire it from the top down on the coil pack
How do you replace the front coil spring on a 1993 Ford F150 4X4?
This is a very dangerous repair unless you have the proper tools and skill. The fact that you ask the question would indicate you do not. Take it to a professional. Serious injury or death can occur if you do no know what you are doing.
How do you reset abs warning light on a 2003 corvette?
Bring to a shop that has an ABS scanner to see if there is a problem - if not have codes cleared
Often rebooting the computer by turning the ignition off then on several times will clear "glitches". Sometimes mine has had to cycle as meny as 20 times to clear a "false" signal.
Checking troubleshooting codes Pontiac grand Am Se without a code scanner?
It cannot be done, you must have a code reader because the system is OBD2, you used to be able to do it without a code reader, but that was OBD1, OBD2 is much more complicated electronics. If you want to get it scanned, you should go to Autozone, they will code scan for free but will not clear codes. You have to pay someone with a code reader to clear the codes, disconnecting the battery doesn't work either
If the main and/or rod bearings are worn, the oil pressure can't be maintained after the oil warms up and thins out. You might be able to get a little more life out of the engine by switching to a heavier weight engine oil.
It is possible also that just the oil pump has worn and can't produce enough pressure at idle. Very often, though, if the pump is worn, so are the bearings, and vice-versa.
2005 Pontiac aztek key stuck in ignition?
Pry off the small rubber stopper under the steering column. Insert screwdriver or pen far enough to move the lever inside, key should turn and be able to be pulled out.
the local shop wanted $1400. DIY cost me about $700 for gasket set and having heads checked.
Is the oil pressure sensor on a 2003 Avalanche the same as on a 2002?
No for the 2003 ACDELCO Part # 12573107 SENSOR,ENG OIL PRESS.
For 2002 ACDELCO Part # D1818A {#12562267} SENSOR,ENG OIL PRESS GA.
If you don't want to pay dealer prices checkout Rock Auto Parts ;-) Follow the link.
Why would there be a clicking sound in the glove box and the heater not blow hot air?
either need a blend door accuator or a heater box
How do you install a heater hose fitting on 2004 Pontiac grand prix gt?
First remove the resovoir tank to have more space. Remove drive belt. Two top bolts and 1 side bolt to remove alternator plus connections( power and ground). Then 3 remove 3 bolts from tensioner housing and remove. Should come out with heater hose fittings. Be careful the fittings could break in manifold. Finally replace fittings and reinstall housing, bolts,alternator w/ connections, drive belt and reservoir tank. Used Dorman heater hose fittings # 47065 from local autoparts store autozone/ oreilly's have replaced them 6 times in past year. 6th was 2 days ago.keep blowing out... its true practice makes perfect. Wrote this in 5 mins!
What is the bolt pattern for a 2001 Pontiac Grand Am?
If its the 2001 model it should be 5x115, pattern is different prior to that year. Hope this info helps!
You cannot find the low side AC servicing port on a 97 GST Manual Tranny Where can you find it?
its located on the drivers side , between the master brake cylinder and the engine block. its a pain to get to. follow the a/c line down to it.
you MIGHT put a little more effort into your question - details &H specifics never hurt.
in a front wheel drive car, bad , loose CV joints clunk upon turning.
How do you reset a car computer or anti-theft system?
To reset the computer in a car disconnect the negative battery terminal until you her a click ( it will be about 5 mins), then it is done.
What force causes a leaf to fall more slowly than a penny?
We know that air resistance (or atmospheric drag) is what causes a leaf to fall more slowly than a penny. A large leaf that weighs a much as a penny has a much greater surface area than the penny, and all this surface area means that the leaf has more drag. Though the leaf and penny will be accelerated by the same amount of force (because they have the same mass), the leaf will present all that surface area to the air, and this will set up a condition of high drag.
Where exactly is the oil pan in a 1997 Pontiac Grand Am SE?
You're also going to have to drop the crossmember if you're changing the gasket
As with all cars, the oil collects it the lowest part of the engine. That's why your oil drain plug is where it is. You can see the oil pan by jacking up the front of the car and putting it on proper jack stands. NEVER support a car on just the jack; I speak from painful experience. If you wiggle under the engine and find the lowest part where the drain plug is you will be able to see the oil pan bolts going up into the engine block. In fact, the oil pan itself with trace the size of the block, so you will probably see a dozen bolts or more around the edge of the oil pan. If you want to remove it, make sure you drain the oil first, and never drain the oil when it's hot or you will be severely burned. If you remove the oil pan, you will need a new gasket when you replace it.
How do you remove the rear two seats in a 1995 Mercury Villager?
First, bring the seat backs all the way forward (so they make a stool seats.) On each of the middle seat "Captain's chairs" there are two levers. There is one on each side of the seat at the hinge facing front. One is on the "outside" of the seat and the second lever is on the "inside" of the seat. Release both levers preferably at the same time) and that will release the front hinges. The rear hinges do not have a release lever and can be "rocked" out of their postings for removal.
How do you replace the starter on a 1993 Pontiac Grand Am?
I just did this job and wanted to add my two cents.
Remove the following.
Battery - 5/16 openend wrench
Duct work in front of radiator - 10mm
Cooling Fan - 10mm
Air Cleaner Cover - open latch, slide left
Rubber Duct from Air Cleaner housing to Throttle Body. - Flat Blade Screwdriver
From the new starter you can get an idea where the mounting bolts are.
They can be hard to find.
Remove long Starter mounting bolt from front side of starter on top side
of engine - 15mm. Ok to remove completely or leave parked your choice.
From under the car remove shorter mounting bolt - 15mm.
Remove starter by working it around over the oil filter. It's a little tricky but you can do it. Place starter on ledge at bottom of radiator.
From top side, remove purple wire that activates starter solenoid. All other wires are on the large terminal that goes to the battery positive. Remove these as well.
Put every thing back in reverse order. Took me about two hours.
PS. If you need to replace antifreeze now is a good time to do it, after the new starter is mounted. Drain is located at right bottom of radiator. It's
plastic so be gentle. Coolant capacity is 9.5 quarts for the 2.3L Quad 4.
For a 50/50 mix you will need 1 gal + 24 oz. of Full strength antifreeze.
Good Luck - and may the Lord give you his peace.
How do you replace the pressure hose on the power steering pump on a 1997 Pontiac grand am se?
under the driver side tire,jack it up for access
What does the code p0440 mean for a 2001 grandam?
Trouble code P0440 means:Evaporative emission control system malfunction
there are over 1000 sounds in the world even in the whole universe
