0
Mazda Protege
Also known as Familia in some markets, the Protégé was a compact car produced by Mazda Motor Corporation from 1964-2003 for the North American market. The Protégé was one of the company’s best sellers and was manufactured in eight generation models.
1,312 Questions
9 times out of 10 is a your EGR valve stuck open due to rust, do a google search for protege low idle you'll find it! good luck
How much does it cost to replace the fan belt in a Mazda Protege?
I just replaced my fan belts on a 2002 Mazda Protege. It came out to a little over $200. I took my car to a Mazda dealership.
Why does your heater not work in a 94 Mazda Protege?
If your heater does not work on your 94 Mazda Protege, check the thermostat. You can also check the heater fuse to ensure it has not blown.
How do you change transmission fluid for mazdaspeed protege?
remove the fill plug, then remove the drain plug, then reinstall the drain plug and add fluid until it comes to the level of the fill plug. remove the fill plug, then remove the drain plug, then reinstall the drain plug and add fluid until it comes to the level of the fill plug.
Where is the PCM located in a 2003 Mazda Protege?
On a 2002 Protege5, it's on the front 'slope' of passenger-side floor.... where your feet would rest if you put them all the way forward. In the '5', you have to take the 'kick guard' plastic off the front-passenger-side of the center console, then peal back the floor carpet. There is the big-ass silver cover/guard protecting it. Not sure if your car would be exactly the same.
How to hot wire ignition of 1991 Mazda protege?
Can someone please tell me how to hot wire the ignition of a 1991 mazda protege?
Where is the MAP Sensor on a Mazda MPV 2000?
It's in front of driver wheel! It is necessary to remove a forward casing (it is attached to a wing) there it will be! It near to system of preliminary cooling.
Where is the ecu in a 1997 Mazda Protege?
Take off the plastic cupholder fairing that surrounds the shifter; it's under the deck and AC controls.
How do you know if the water pump has failed?
you need a flow switch, a alarm sounder and a relay based XOR connection. that is based on 2 No 4pdt relays. check the web for relay based XOR command. Jovan Ristov
Hope this helps
Why is your Mazda Protege overheating?
that is a great ? and hard figure out because it could be 1 of many reasons. i reacently had this happen to me and it took mechanics 2 months to figure it out imagine that! it was a stopped up radiator. but in addition to that it could've been blown head gasket, a fuse, a sensor, water pump, plugged heater core for anyone out there that has a 97 protege if it is overheating DO NOT drive it if it's running more than 20 degrees above normal temp. the darn thing has plastic rings. good luck
What does the tail light fuse have to do with the radio in a 1998 Mazda protege?
have two fuse boxes in this vehichle one under the dashboard on thedriver side one under the hood by the battery
How do you put back the headlight retainer clip for a 03' Mazda protege the correct way?
the same way you pulled it out . if you frgot then look on the other side and see how it looks like
or
Bulb goes in first, then the single wire side of the clip (rotate bulb slightly during the next step until it fits right) to hold bulb in place. The hook side hooks in downwards, which is a little counter-intuitive.
Where do you add transmission fluid to a 1993 Mazda Protege?
good answer if its an auto, the fill plug is located on the tranny, there are 2 plugs, one on bottom, and one in the middle/top area. Use a funnel, and place it in the dipstick. Add the tranny fluid there. Where the dipstick is.
How do you disassemble the headlight piece to replace the bulb on a 2002 Protege 5?
Behind the headlight, on the farthest outer side, there is a connecting plug & a black rubber boot. Pull the boot away from headlamp, rotate the piece that the connector is attached to and out comes the bulb. Hope this helps!
How do You replace drive axel's on 1998 Mazda Protege?
tire off, brakes off, tie rod off, disconnect strut, and a few holding bolts. axle will slide out with a little bang from a hammer or a little pull if your lucky
What do you do if your car is overheating?
Shut it off!
Let it cool. (this may take an hour or two)
Check:
- Coolant Level
- That the air to the radiator is unobstructed
- The drive belts for water pump etc are working.
- that the enigine has oil
If all these check as proper the car will have to be checked by a qualified person.
No , the 1.8 liter 4 cylinder in a 1999 Mazda Protege is not an interference engine
What is the signal wire for MAF for a 94 Mazda protege?
need to know what wire go were for a 94 Mazda protege MAF sensor
What might cause a '92 Toyota Corolla to die when you give it gas but idle fine?
clogged fuel OR air filter,vacuum leak,probably to the distributor,clogged muffler or resonator if you've already checked the catalytic converter.Is it automatic???
would have to agree with that most likely clogged fuel filter
Change your fuel filter because your filter is all clogged up.
Does it do this after running for a while? I had a similar problem which was down to overheating (which in turn was due to a loose head). Theory goes that the fuel in the carbourettor was evaporating due to the high heat - after letting the engine cool for half an hour it started again. May or may not be the cause but HTH
Fuel pressure regulator may be bad, also check the spark plug gap.
How do you fix a Mazda Protege with a bad crankshaft sensor?
locate the crankshaft sensor which will probably be behind or right next to the crank shaft which is under the timing belt cover you might have to take the cover off and the timing belt
How do you change front brakes?
Get yourself a repair manual at most auto parts stores. Around $12. There you will find all the information you need to accomplish this task and many more.
How do you replace fan belt on 1997 Mazda 323?
This is from the Owners Handbook of my Mazda 323, 1996 :
Alternator Drive Belt.
1. Loosen the alternator mounting bolt and adjusting bar bolt. Replace Fanbelt.
2. Turn the adjusting bolt until the correct tension is obtained. The deflexion should be 10mm.
3. Tighten bolts and recheck the tension.
Where can you find a a vacuum diagram for a Mazda Protege LX 1.5l engine?
There's a label under your hood that has the diagram. If the hood has been replaced with an aftermarket one, there will be no sticker like that and you will have to buy a manual.
