0
Mercury Villager
The Villager was a minivan manufactured by Ford Motor Company from 1993 to 2002, and was a rebadged version of the Nissan Quest. Designed by Moray Callum, the Villager featured a five-speed automatic transmission and a front engine, front-wheel drive layout.
1,605 Questions
How can i disable alarm activated on 1996 mercury villager Horn and location this part please How_do_you_disable_factory_alarm_activated_on_1996_mercury_villager_Horn_headlight_are_blinking_continously.
What does the proportioning valve do on a 94 villager?
it stops the wheels from moving. If this locks up, take a 20 lb sledge hammer and hit ur wheel with it ------------------------------------------- The above is a disgusting answer that must have been written by a Neanderthal. GET A LIFE ---- The proportioning valve regulates brake fluid pressure from the master cylinder to the front and rear wheels accordingly.
What is the correct spark plug gap for a 1998 Mercury Villager?
I was looking at the 1998 Mercury Villager Owner Guide ( and one of the Ford
websites ) and they both show the spark plug gap as ( .034 inch )
Mercury villager rear wiper motor runs all the time?
You may want to try removing the wiper blade and shaft nut first to eliminate the blade from continually moving. Then, consult your mechanic.
Where is the power window relay located on a 1995 Mercury Villager?
It is to the right of the steering wheel, behind the paneling below where your knee would rest. You do not have to remove anything, you can just reach behind the paneling.
Is 10w40 oil ok to use in a 1998 villager?
The 1998 Ford/Mercury Villager came equipped in the 3.0L V6. For this application 0W30 and 5W30 are specified for all-season use. 10W40 may result in decreased fuel economy and is not needed for this application. No damage will be sustained if 10W40 is run or used as top-off.
Symptoms of a bad knock sensor?
There are no symptoms since the knock sensor doesn't do anything unless the engine is detonating, in which case it would do nothing and you would hear it. The knock sensor code is often tripped when there is a fault in something else since it's part of the same circuit. This is considered a "ghost" error code.
It could be dirt in the carborator or the timing chain is starting to go, but that usually just dies and the car will not start again. It also could be a problem within the exhaust system.
I have had the alternator changered with no results.
Where can you find Diagram of 2000 Mercury Villager exhaust system?
Library? Chilton/ Motors / or Haynes Manuals?
What is connected to the thermostat on a 1995 mercury villager?
depends is it the thermostat housing or the gasket. it is either connected to the hose or the water pump
What is the right octane for a Camry 2001?
Toyota recommends 91 octane for the 2001 Camry with the V-6 engine. This car gets 20 miles per gallon in the city and 27 miles per gallon on the highway.
Why would the cruise control and horn not work on a 2002 ford mustang?
Damaged clockspring coil?
check your fuse it works the cruise control, horn and cigar lighter
My 1999 villager stalls while driving?
could be a vacuum leak >> http://wiki.answers.com/Q/Your_94_mercury_villager_stalls_when_slowing_down_idle_low_below_800rpm
How do you disable the seat belt motor on a 1993 Villager?
Finally a good answer to this question. I searched for a long time on different sites but could not find a satisfactory answer. I figured it out myself and here it is. The controller module for the seat belts are located inside the car. It is under the dash way on the floor in the middle console. How you can get to is: remove side panel closest to your accelerator with light on it which is held in by two plastic screws on the outside and a metal one on the inside. you will see a stack of different modules, it is the last box closest to floor of the car. It's black plastic relatively small and says Ford Made in Canada on it. There are two bronz looking screws you don't want to open those. Lift floor covering and there is a black screw holding the unit, open that one and do the same on the passenger side. Once you got it out make sure your seat belt position is where you want it. and take out the two plugs out of it and wala :)
What is the spark plug gap for a 1993 Mercury Villager?
According to one of Ford's websites :
The spark plug gap for a 1993 Mercury Villager , 3.0 V6 is :
( .032 inch )
Is there a fuse for the license plate lights on a 1996 Mercury villager?
Should be the same circuit for parking/tail/dash lights
What might cause your 1996 mercury villager transmission to hard shift?
Generally, one should have the codes scanned to make sure all the sensors are working correctly. Out of spec sensors can cause damage to the transmission. Make sure the alternator / battery voltage is correct too as I've had hard shifts when my alternator died. Failing that, you'll need to have a transmission shop check it out, working on external checks first before tearing it down.
guessin frt and rear are sep systems so check the frt. lines. same system. you are low on freon.
Where is the low pressure port on a 1996 Mercury Villager?
This vehicle uses R134A refrigerant and the connectors that it uses are not interchangeable or reversible(on the vehicle side). That doesn't mean you cannot screw it up, if you were to connect the hoses to the wrong side of your manifold set, but if you are using the auto parts store recharging line and little cans of R134A they will only connect to the low side port.
Coincidentally if you look up at the hood above where the low side port is you will see a sticker with the amount of regrigerant and oil that your particular vehicle uses. Mine has the rear AC so it uses 3.75 pounds of "freon."
How do you remove the rear seat from a 1998 Sebring convertible?
# Slide your fingers underneath the bottom part of the seat from the front. # Pull up. Hard.
I have a 1996 Mercury Villager and battled this problem for years. My van would stall on hot days, at high altitudes and sometimes just randomly (even on the freeway which posed considerable dangerous situation). Several dealers and mechanics could not diagnose the problem. I finally had the fuel pump replaced and the problem has not reoccurred. However, I agreed to use an after-market fuel pump and it does not give accurate fuel gage readings. You might want to consider using the dealer brand (which was considerably more expensive).
