0
Pulleys
A pulley is a mechanism composed of a wheel on an axle or shaft. A rope, or cable usually runs over the wheel and inside the groove. Pulleys are normally used to change the direction of an applied force to make the work easier. It is one of the six simple machines.
1,797 Questions
How do you remove the crank shaft pulley on a 1995 Mitsubishi 3000 GT?
This question answer requires a service manual Crank shaft pulley removal is a complicated procedure and should only be done by people with experience as many parts need to be removed including the timing belt which if not done properly will cause damage to the engine. It would take the novice at least a day to do the job and requires some specialty tools. Go to Team3s web site for all of the information needed or Erik Gross s site. You may as well do the 60k and change all of the other parts involved while you are at it. The motor is an interference motor and putting the timing belt on improperly will cause the pistons to hit the valves so "Beware"
How do you de-tension the serpentine belt on a 1995 Chevy Cavalier?
If your car has a tensioner pulley it can be moved to release the tension on the belt for removal. Make note of the routing of the belt before removing it. This will make installing the replacement belt much easier. If you do not have a tensioner pulley one of your accessory motor/pumps (most likely your alternator) can be moved in order to release the tension on the belt.
Most tensioner pulleys have an hole the exact size of a ratchet drive on the tensioner arm. This allows you to put a standard ratchet (without any socket attached to it) into that hole and use the leverage of the ratchet to release the tension.
What does a smaller supercharger pulley do to a cars engine?
The smaller pulley spins the supercharger faster, thus creating greater boost and therefore more horsepower. Popular "sizes" are 15%, 17% and 19% reduction. The larger percentage reduction gives a greater boost. Some mechanics do not recommend the higher percentage pulleys.
How do you replace the water pump on a 1999 Daewoo Lanos?
How do you install a power steering pump on a 2000 dodge 2500 diesel truck?
Go to AutoZone.com "Do It Yourself" tab for on line instructions.
How do you build a homemade ground ultrasound machine?
"As is the case with X-rays this is no hobby for the amateur or (Ham). As far as I know it is illegal for an amateur to construct or operate an Ultrasound machine as you describe it and these are (completed models) restricted to licensed Medical Labs and practitioners. In other words it"s for the most part and for the soldering-iron types, against the law! I have never even seen an advertisement for a kit or schematic plans for such a device. Try something more palatable like weather computers(there were both analog and digital varieties) or maybe Night Vision devices."
The answer above is completely absurd, and does not even address the question. First of all, comparing ultrasound to x-rays, shows no knowledge of science. Ultrasound is merely sounds waves of higher frequency than can be detected by human hearing. Unlike x-rays which are electromagnetic energy, and are dangerous to human health if overly exposed. The answer also confuses ultrasound medical devices with what the question is asking, which is about ground penetrating ultrasound machine. Npw to address the question. Ultrasound, as mentioned, is high frequency sound. The problem here is that these waves do not penetrate very far into the ground and are unsuitable for detecting buried objects. Traditionally the mining industry uses explosives to generate the sound waves needed for deep ground penetration. Relatively small explosive charges are placed into holes, and microphones are placed in a matrix to record the shock waves bouncing back. Then the data is post-processed with powerful computers to create images of the sound waves resulting from the explosions. So, building a homemade version of this is probably impractical. There are portable ground penetrating radar machines, but that would be a whole different question.
The above answers do not take into consideration the research going on since the 1990's into ground penetrating ultrasound devices for landmine detection. The single drawback these devices have is the requirement of having a water saturated ground environment for the ultrasound to render clear and meaningful pictures. But, when operated in such an environment, they produce top quality high resolution photos of all kinds of materials - not just metals. Seeing something as tiny as a hairpin, at more than a meter - or being able to tell if a dime is heads or tails under a foot of soil.
Did Archimedes perfect the lever and pulley?
maybe the pulley but not the lever
he invented the pulley but not the lever
How do you relax the tensioner pulley on a 2003 trailblazer?
There is a square opening on the front of the tensioner that fit a 3/8" ratchet. Place the ratchet in the opening and crank down toward the ground. You may need to slip a longer bar over the ratchet to get it down.
What jobs use combination pulleys?
Tree trimming uses combination pulleys. Also combination pulleys are used to lift engines out of cars to work on them. Some construction sites use them in places they cannot get a crane.
Are books mass produced If so using what type of printing machine?
Yes, by something a lil more recent than Gutenberg's!
You would need to remove the pulley and place a smaller pulley on to make the supercharger turn faster and pump more air. This can be done to a point but if you go too small without doing alot of other modifications to the intake and exhaust you will burn up your motor in no time. Check out the following website. http://www.gtpworld.com/index.html Read and learn from others mistakes. Hope this helps.
How do you set serpentine belt tension on a Chrysler?
The tension on a serpentine belt is automatically set by the Idler Tension Pulley. If you find it is not correctly setting the tension, the the spring may be broken.
It could be the clutch fan that is going bad. I had the same issue & the expense of the part and manpower can be $400 to $700.
I just changed the sc pully on my 2000 GTP and I ordered a puller from eBay for about $100. It took a lot of torque to get it off. It took almost an hour to remove the old one and 10 mins to install the new. The puller makes contact with the entire pully so there's even pressure. Checkout www.3800performance.com and www.grandprixstore.com. They have pullers.
00gtp
Did you look at the alternator bearings?Take the belt off and spin the alteranator to see if the bearings are bad.
A pulley costs anywhere from $19.99 to thousands of dollars. It generally depends on the type of pulley you're seeking and the size of the pulley.
How to remove pulley from dodge water pump?
Best way is to purchase a water pump pulley remover, they are pressed on and have no way to grab with a conventional puller, the specialty puller is fantastic and not too expensive. Many are just bolted on so check that first.
How do you replace the pulley tensioner on a 1994 Chrysler lebaron?
If you are lucky like me you spray a lot of WD40 on the hub and use wrenches to work it back and forth until you feel the spring action. otherwise, good luck . use PB Buster it is better than WD 40 It is made for freeing rusted bolts and screws
Tensioner pulley for a 93 mercury villager?
If you mean the Timing Belt Tensioner, it is behind the timing cover, just above the crank shaft to the left. Note: even though too many sources say that the 3.0 liter engine is an interference motor - its NOT, it was designed by Nissan (at the request of Ford/Mercury) be safe if a timing belt breaks - I can attest to this- I have replaced a couple of broken breaks - no valve or piston damage.
How do you remove the pulley of the power steering pump on a 1995 jeep wrangler Rio Grand?
look and see if there is an opening for an Allen wrench in the front of the shaft.if there is use an Allen wrench to hold the shaft and an open end wrench to turn the nut
How do you put rope through a rope pulley?
no it can have anything that is like a rope, for example a steel cable or my big a s s pen15
Change 2004 grand prix supercharger pulley?
You will need a supercharger pulley tool to do the job right so you dont risk damaging the shaft of the blower, companies such as zzperformance or intense racing have them available for purchase or just a one time rental
http://www.zzperformance.com
http://www.intense-racing.com
