Toyota 4Runner

Get a can of WD40 and spray the inside and outside of the dist cap and all of the plug wiring and coil.

Check your local public library for 3rd party maintenance books.

Dis-connect the battery first. There should be a hole in the bottom of the steering column, underneath the lock. If you can get a small screwdriver, or punch, and push in on the release button for the lock, while the lock is in the "run" position. You should be able to pull the lock out of the cylinder. If the part of the key shank is not too badly damage, you can then work it out of the lock, and it will be re-useable. Use some graphite and and the spare key to work the lock before putting it back in. If the key shank is too mangled, then you can get another lock from the parts store for about $15.00.

Just to clarify...on the 2001 the hole is in the top of the cylider barrel and the key will have to be turned to the first notch. If it is fully engaged, it will not release the cylinder. Remove the lower column cover first by removing the three screws that hold it the bottom cover in place.

That depends on the size of the engine

you should be able to find a shop manual at the local library with the right information on this -- make copies of the pages, as they are usually for REFERENCE only...:) OR Just visit this site and find the article on air filters.... http://www.toyotaownersonline.com/parts-service/diy.html

They are both on the same circuit depending on the model of vehicle you have. Look at the fuse panel and if you have a manual that will tell you the tail light fuse then check it. If not then pull them one at a time and replace any you find that are bad. If none turn out bad then there is a relay in some models after the fuse. It should be mounted under the steering wheel dash area.

same as a 2005 odometer OS on turn key off hold reset turn key on loght flashes then turn off

I have had to go underneathe the car and use a pair of vise grips or pliers to turn a crank that is to the rear drivers side of the tire. that is about the only way to do it unless you have the crank that hole is for the crank to go thru. it veers to the left a little is why it looks like it doesn't go anywhere.

The 2007 Toyota 4Runner has a V6 engine.

The 2003 Toyota 4Runner's engine produces 282 ft-lbs. @ 3800 rpm.

If it is a 4x4 with "neutral" on the transfer case, put the transmission in park and the t-case in neutral. If it is not a 4x4 or does not have neutral on the t-case, then the answer is simply no. The transmission should be an A43D or R154 IIRC, and does not circulate fluid w/o the engine running, so will burn bearings and bushings if towed much more than about 5 miles.

There is one other option, which is to let the engine just idle in neutral while it is being towed, as this will keep fluid circulating.

How do you program a keyless entry for a 2002 Avalon?

FOR AUSTRALIAN AVALONS.

Start with the ignition in the "Lock" position.

CYCLE IGNITION ON-LOCK 3 TIMES THEN ON.

SECURITY LED NEXT TO THE CLOCK SHOULD LIGHT, INDICATING READY TO PROGRAM.

PRESS THE KEY FOB "DOORS" BUTTON FOR A SECOND.

BOTH TURN INDICATORS SHOULD BLINK TO INDICATE ACCEPTANCE.

(IF REQUIRED FOR 2ND/3RD KEY FOB) PRESS THE KEY FOB "DOORS" BUTTON FOR A SECOND.

BOTH TURN INDICATORS SHOULD BLINK TO INDICATE ACCEPTANCE.

SWITCH TEH IGNITION TO "LOCK".

REMOVE KEY, WAIT A SEC AND TEST.

O2 Sensors require a special socket that has a slot cut in to one side for the wire that runs from it. This socket can usually be purchased or rented from most Auto supply house. They come in I believe in three size.

There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.

all the slinding rear windows that i put in you had to replace the whole rear glass

i dont think 4runners have a reset button. the tires have sensors in them that tell a computer how much pressure there is. make sure all the tires have 32psi (including the spare, it has a sensor too) and the light should turn itself off. there is a service bulletin on vehicles with this system. in very cold weather, the pressure needs to be higher than 32psi. take it to the dealer if you have a 2003 or newer 4 runner if youd like details on adjusting pressure for colder weather.

Drill it out............

The only way to turn them off is to pull up the park brake or remove the relay in the fuse box beside the battery marked DRL

It could be all manner of things. Your truck will give you a code by way of blinking lights in the dash. You jump e1 to te1 in the diagnostics port. You will have a series of blinking lights with a pause between numbers. Example-blinks once then blinks 7 times right after that its a Code 17 look it up in an fsm it will tell you what the code means.

34 9.5 15 tsl fit on my stock 94 4runner with a 3/4 torsion bar crank. recommend suspension upgrades. i would say the same for a 33 unless the "33" inch tire is closer to 32 inched tall. manufactures are not always accurate.

a tire with actual dimensions of 32.6 inches tall by less than 11 inches wide will work on almost any stock Toyota truck

The PCV valve on the V6 3.4L is on the right (passenger side) valve cover. It is on top of the valve cover, near the front of the engine, and an inch or two behind the black plastic timing cover. It is easy to see because it has a black rubber hose coming out of it. The other end of the hose attaches at the front of the intake manifold near the throttle body.

The dealier for a fee.

This Maintenance light is a reminder : "TIME FOR AN OIL CHANGE!"

1. Turn the ignition key to the 'OFF' position with the trip meter A reading shown.

2. Turn the ignition key to the 'ON' position while holding down the trip meter 'RESET' button.

Hold down the knob for at least 5 seconds. The odometer indicates '000000' and the light goes off.

From pg. 136 of Owner's Manual.

Make sure odometer (ODO) is slelected (not trip odometer). Hold in odometer "reset" botton. Turn Igniotion to ON but do not start engine. Light will flash and go off. Turn Ignition OFF. Release "reset" button.