0
Turn Signals and Hazard Lights
Turn signals and hazard lights refer to the lights on an automobile designed to alert other drivers or pedestrians. Turn signals indicate where the vehicle intends to go, while hazard lights warn others of an emergency.
4,468 Questions
Where is the flasher unit located on a 2001 Nissan x-terra?
It's basically under the steering column. If you lay on the floor and look up you should be able to see it using a flashlight. It's a black plastic box like shape and it slides onto a metal mounting bracket. If you want the original Nissan part, it's $73, you can get a generic for $10 but it doesn't mount back on the slide and just hangs there unless you use electrical tape or something else to attach it.
How do you replace the hazard flasher switch in a 1999 VW Passat?
It's really easy. There is a blank filling a hole directly below the hazard sw. Use a small screwdriver, and carefully prise this out. Insert your finger into the hole, and up into the back of the hazard switch and ease it forward. you can prise it out with a screwdriver also, but i found this method offered less chance of damage to the dash.
On a side note, my 2001 wagon has the heated seats & so the blank is below not only the hazard relay switch but the heated seats control knob. So it's unreachable from the blank spot. That being said I just popped the switch out as described. (I used a butter knife) to get the face of the button off then pliers to pull the switch out. Easy as pie.
Where is the turn signal relay located on a 1999 jeep wrangler?
Front seating area, under the left hand side of the instrument panel, right hand side of steering column.
Curtorsey Auto Zone.
How do you turn signal lights in a Ford Aerostar?
Take hold of the turn signal light connector. Push the connector in and turn at the same time. The connector and light will come free. Do the same with the light bulb to remove it.
Why is it good practice to cancel the signal light after making a lane change?
It's good practice to manually cancel the signal light after making a lane change because the small movement of the steering wheel is not likely to cancel it.
How do you change your blinker?
- Remove the lens for the blinker. If there is no lens to remove, as in some front blinkers, open the hood and look behind the
blinker location. There will be a socket for the light to go in.
2
Remove the bulb by pressing down on it slightly, and turning counter-clockwise until it comes loose from the housing. This is the part that is apt to be problematic, especially if the bulb has "burned" itself into the socket or otherwise melted something, causing it to hold fast. Should this happen, disconnect the battery, and break the glass on the bulb. Then, with needle-nose pliers, turn the bottom housing of the bulb counter-clockwise until it comes loose.
3
Install the new blinker bulb in the reverse order of removal, and replace the blinker lens, if applicable. Check blinker to ensure it works.
You Will Need a Screw Driver.
- Remove the lens for the blinker. If there is no lens to remove, as in some front blinkers, open the hood and look behind the
Why should you use your turn signal well in advance of a turn?
So that traffic behind you is able to anticipate your turn, and can act accordingly.
Why has my turn signal shifter stopped working when signaling left?
One of the signal bulbs may have burned out.
Open hatch. Theres an access hole inside towards taillight. Unscrew plastic knob by hand. Along side of taillight -(outside of car)- in the drip rail- there is a Philips head screw. Undo this and pop taillight assembly out. Turn bulb holder to remove. Reverse process to install
Where is the turn signal flasher located on a 1992 Nissan truck?
(above the clutch pedal, attached to brake pedal support arm. black, 1.5in x 1x1in approx, 3 wires coming out of bottom)
How do you replace a turning signal bulb on a BMW 330ci?
BMW 330CI turn signal light bulb replacement: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the turn signal light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
What might be the problem if your 1995 Chevy Blazer will not start or even turn over?
siezed engine/dead battery
Answerpossibly a bad ground Answeryour starter might need to be replaced Answeri have gone thru this with 2 1995 blazers.....although my 1st one didnt seize up, the problem was the same on both....1st of all check your oil level...if its high,your problem is the fuel injection "fuel pressure regulator which sits under the plenum....this goes bad and floods the right bank sometimes getting what seems to be a seized up situation, really whats happening is kinda like getting a vapor lock and the motor will not turn over.....to replace the regulator isn't that tuff....undo the sensors on the top...then unbolt the nuts/bolts(12 or so) starting at the left front corner and working your way around...lift it off in the center you will see your injection "spider"...go to auto zone and pick one up or order it, plus the gasket(the regulator is about $40.00 and gasket is about$6 OR 7...comes with "O" rings and a special screw driver adapter to remove 2 screws (top and bottom)replace and put the plenum back on....bolting back down in the opposite direction....snug all then tighten to specs,hook your sensors lines ,air cleaner,etc...might be a great idea to at least replace the 3 plugs on the roght/passenger side THEN....CHANGE THE OIL/FILTER before starting...what has happened is fuel filled those cylinders,ran right past the pistons into the oil... the motor got whats was basically a vapor lock.....now i had to keep hiting the starter and added a jump from another car for a little extra boost....FINALLY it started to crank over a little at a time then cranked normally, i featherd the gas pedal a little and it finally started,blew a hell of alot of white smoke out.. i drove around nice and easy for awhile...after that, it was fine....by the way...if you saw the beautiful condition this blazer is in, all the receipts from the previous owner, new brakes,new michelin tires, its an LT with all options including leather.... i bought this from the dealership where the guy traded it in... they thought the motor was seized... i bought the blazer for $650.00!!!!!!!!!!!!!!!!!!anyone wanting any other info on this can email meredrx791@yahoo.comCould also be an ignition switch..
How do you replace turn signals on a 2002 impala?
If you mean "Lamps"; In your "Owner's Manual", for Front see page 6-36: Headlamps, Front Parking and Turn Signal Lamps. For Rear see page 6-38: Tail/Stop/Turn Signal and Rear Sidemarker Lamps, under Section 6: Service and Appearance Care - Bulb Replacement...
Check the fuses.
Where is the flasher located on your '95 dodge stratus?
if you mean the flasher button it is behind the steering wheel in front of the guage display
Your right turn signal doesnt work everything else does?
usually this is a bulb burned out on the left side
How can you tell if signal flasher is going bad and where located in 2003 Trailblazer?
The fuse box is under you back seat! The rear signal flashers have their own control board located in the taillight housing. I have had to replace mine before. I am not aware of any fusebox under the back seat. I will have to check this out.
Where is the signal flasher located on a 2003 Sunfire?
in the fuse pannel located on the drivers side of the dash facing the door.
How do you change front turn signal on Chevy Venture?
Hi,
The hard part about changing the turn signal bulb is getting the light assembly out. But that is not really that hard. There are three "wing nuts" that hold the turn signal and headlight assemblies to the frame of the van. You have to remove the wing nut that is closest to the outside of the van and then pull the turn signal and side marker assembly straight out. This will allow you access to the bulb sockets at the back of the assembly.
At that point you just remove the socket, pull the bulb straight out, and put the new bulb. I always like to test that the bulb is working before putting things back together. Once you have verified that it works, line up the tabs at the back of the assembly with the frame hole and push it back in place. Then reinstall the wing nut and you are all set.
There should be a link on this page that shows pictures of this area and the operation. Take a look!
Good Luck.
Replace the signal flasher relay assuming you have physically seen front and rear, left and right signal bulbs flash.
Does temp light lite when ingnition is turned on in 1989 voyager?
no, at least not normally, if it does your cooalant temp. sensor is prob, shot and it is located near your upper rad hose where it contacts the engine.
