0
Buick Rendezvous
This category covers questions about the Buick Rendezvous, a mid-sized crossover SUV that was manufactured by General Motors and sold through its Buick division. The Rendezvous was produced from 2001-2007 and was succeeded by the Buick Enclave.
1,007 Questions
Where is the coolant sensor on a 1991 Chevy Lumina?
Here's a link to a schematic and instructions on replacing the coolant sensor (from the Auto Zone website) http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c15280067b92 Good luck!
Why does your steering wheel vibrate the higher the speed goes?
Your steering wheel will vibrate at higher speeds due to either wear in your front tires or improper balance of tire pressure. IF these are not the promblem look to see if there is damanage to the shaft under the vehicle between the tires. Look at it or get it looked at before it gets worse, believe me I know how expensive it can be later!
Where is the powersteering pump on a 2004 Buick rendezvous?
The Power steering pump is located underneath where you put the power steering fluid.
Where is the coolant temp sensor on a 2003 Chevy s10 V6 and how is it replaced?
The coolant temp sensor on a 2003 Chevy S10 V6 is located on the front of the intake manifold. To replace simply unscrew the old sensor and screw on the new one.
Rear hatch locks on 2005 buick rendezvous?
Yes it does. It is an electric servo, not manuel. You open the door by squeezing a switch just under the handle, or by pressing the "rear hatch" button on your remote.
How do you install a windshield on a 1970 Chevelle?
To install the windshield, im assuming you have the glass out.
1. Remove the rubber around the pinchweld
2. put the rubber around the new glass
3. get a rope
4. put the rope all round the rubber in the inner lip
5. Spray some lube spray all around the rubber (oil works too)
6. Carry the glass to the vechile and line it up
7. go inside the car and pull the rope
8. When your pulling the rope you will start to see the lip on the rubber gasket over laping the pinchweld.
9. Tap the glass with your hand using all five finger (not your fist).
That all to it.
I'm on my 7th 1970 Chevelle and I have never seen one with a pinchweld gasket, ever.... Remove the old one with a guitar string or whatever, kill the rust, and 100% silicone in the new one.
And that's not all there is to it...... please have the appropriate tool to remove the chrome molding or you WILL ruin it.
The thermal relay may be bad.
Have heated seat in 2002 buick rendezvous drivers doesn't work passenger does?
Might be the IP switch or the elements gone out no way to find out without testing the switch
How to remove the brass cover of a cast iron trap should the cover be heated first?
Terrible idea , great way to get yourself killed as the sewer lines could contain dangerous fumes that are highly explosive methane , hydrogen sulfide etc. An open flame is an invitation for a violent reaction .=One easy way is to chisel it out as non ferrous metals do not spark THAT IS WHY THEY USE Plastic or Brass plugs=
What is the firing order for a 2003 Buick Rendezvous?
How do you change the cabin air filter in a buick rendezvous?
Where can i get a free 1999 Nissan Pathfinder Bose Stereo wiring diagram?
http://wiki.answers.com/Q/Where_can_i_get_a_free_1999_Nissan_Pathfinder_Bose_Stereo_wiring_diagram"
Where is the brake fuse located on a Buick Rendezvous?
There are two fuse boxes on the Rendezvous' - one on the passenger side at the floor and one under the hood right against the windshield on the passenger side. In the owner's manual is a diagram of which ones are which. Hope this helps! There are two fuse boxes on the Rendezvous' - one on the passenger side at the floor and one under the hood right against the windshield on the passenger side. In the owner's manual is a diagram of which ones are which. Hope this helps!
What could cause a car to shudder upon acceleration?
I have not had experience with fuel injected vehicles, assuming yours is, but I have experienced such a thing on many occasions with carburated vehicles. On such, plugged jets in the carburetor actually cause the vehicle to shudder when under load. If the vehicle is fuel injected and hasen't been serviced recently you may want to have this checked out.
Another AnswerIf an automatic vehicle and feels like you're driving over a cattle guard, good chance it's the torque converter that's going out. If so, it doesn't happen so much if you take off from a stop and continue a constant and somewhat aggressive acceleration. It also happens every time if going through a school zone at 35ish for a while, then trying to speed up. That's a torque converter unable to lock up. When you feel it, back off the gas! If that torque converter does come apart inside, your car is going nowhere.Anyone have a Wiring diagram for a 99 crv stereo Please?
Try the "Install Doctor" website. The following two documents have a CR-V Radio Wiring diagram and a general Honda Radio Wire Harness diagram: http://www.installdr.com/InstallDocs/Honda/PDF/466009.pdf http://www.installdr.com/Harnesses/HA-Wiring.pdf
What causes AWD light to come on in Oldsmobile Bravada?
Most offen its the encoder motor it is a electric motor the engauges the All wheel drive its located to the passager side of the transfer case and can be bought from auto parts store for around 170.00$ Thanks James
How do you measure the change in value of money?
Price indices are used to measure the general price level change in an economy. Price levels are calculated periodically using a price index and compared with previous years. The price index usually contains select goods and services that affect consumer spending, these include food and drink, household goods and services, clothing, etc.
The source of your problem is the rear differential. This is what allows one wheel to spin a greater or lesser number of times than its opposite counterpart. In my Rodeo (4wd V6 LSE) i have a limited slip differential. You can tell if you do too by checking the sticker under your hood on the driver's side. If it says G-80 or something like that (I can't quite remember) then you too have an LSD. What's important about a LSD is that one needs to add LSD additive to the Gear Oil when changing the differential fluid (should be done every 30k miles in the Rodeo). If your differential fluid (gear oil) is too old or missing the additive, the LSD can act up and cause a grinding noise during tight turns. Before you do anything else, change your differential fluid. It's easy, cheap, and my problem went away as soon as I did it. Hope this was some help.
An easier way to see if you have a limited slip is to lift both back tires and spin one tire, if the other tire turns the same way then you have a limited slip, if it turns the other way then you'll have an open differential.
Make sure the contact points on the little black chip in key are clean and ensure the chip is centered in the key. If security light goes on you must wait a few minutes for it to go off before attempting to start car again.
Why is there water leaking on the passenger side floorboard of my 1994 ford tempo?
Would that be when it is raining ? If so you need to caulk around the vent in the fire wall area. If not from rain, then the heater core is leaking, and you will be losing coolant.
Can you add subwoofers to a stock sound system?
Yes and no. You can, but you will need to have an amp to power the subs. You will also have to have a way to control the volume to the subs. I recommend getting a new radio that can controll the subwoofer\amp part of it. Hope this helps
Your 2004 Buick Rendezvous is leaking a black liquid from Cadillac Converter?
"Catalytic Converter" not cadillac, lol. The black liquid is carbon soot mixed with water from condensation in your exhaust. The carbon soot is from the oil that lubricates your engine, it also gets small amounts in the combustion chamber, thus when your fuel/air mixture ignites in the (combustion) chamber, the oil (with carbon in it) is burned off and exits with the exhaust.
