0
Crankshaft Sensors
In an internal combustion engine, a crankshaft sensor is a component used to monitor the rotational speed and position of the crankshaft. The information provided by the sensor is used by the engine control unit to manipulate ignition system timing.
2,765 Questions
It's a recall, dealer will do it for free.
Where is the crank shaft sensor on a 2000 GMC sierra located?
in the side of the block, above the started
Where is crankshaft position sensor located on 2003 dodge stratus?
Easy :) All you have to do is put your car up in the air, walk under it and you can see the connector just behind the front lower engine mount bracket. (driver's side)
I will be removing the mount and bracket, supporting the weight with a transmission jack, then removing the sensor.....
Hope that helps.
The code p1391 stands for intermittent loss of CMP or CKP-what does CMP and CKP stand for?
CMP-camshaft position sensor
CKP-crankshaft position sensor
CMP-camshaft position sensor
CKP-crankshaft position sensor
Where is the crankshaft position sensor on a 1995 Chrysler Concorde?
It is on the passenger side of the transmission bell housing, just behind the engine.
How do you change the cam position sensor on a mk3 mondeo?
Extremely easy to do. Hardest part is spotting the part but it is at the 'front' of the engine, almostin line with the bonnet release catch and just beneath the fuel rail. The electrical connector pulls of and all you need is a an 8 mm. spanner preferably a socket type to unscrew the single retaining bolt. It takes just a few minutes to do the job.
I have a 1990 Pontiac Safari wagon that would not start,after much testing we found one bad fuel injector replaced it and car started but ran terrible, did more testing and found bad ignition module, replaced module runs better but now have code #43 knock sensor and engine is running in default mode switched ECM no help must be knock sensor don't think knock sensor would keep car from starting but the other things mentioned here would. Hope this helps. This wagon has 3.1 engine. Havent changed knock sensor yet.
Where is camshaft position sensor at on a f 350 ford with a 7.3L diesel?
If you are looking down it is behind the fan on the passengerside of the motor right above the crankshaft pully it has a 10mm bolt on it and a three wire harness with a piece of chrome sticking out over the pulley.
There are multiple uses of the term in the construction field, but end bearing is a term which usually specifies that a member (a floor joist for example) is resting on or abuting a vertical member (a load bearing wall for example). The more the end bearing (the area of vertical wall contacting the separate member) the more the load can be distributed evenly.
In the example given, if the horizontal member supported more weight than the end bearing capacity, it could crush the sill of the load bearing wall and cause the system to fail.
Where is the crankshaft sensor located on a 1996 dodge stratus?
On the 2.0 and 2.4 engines, it's on the right rear of the engine. On the 2.5 engine, it's at the rear of the distributor.
Rick
I'm a retired ASE Master/L-1 Technician. I still keep current with the latest automotive technology. Visit my blog for cool articles and TSB's: http://free-auto-repair-advice.blogspot.com
What happens when an air temp sensor goes bad?
A faulty intake air temperature sensor can cause a number of issues in a vehicle. Among these problems are taking longer to start on cold mornings and increased consumption of fuel.
Can you use motion sensors for speakers?
Yes you can. here is how. you take of the back of the speaker if possible. look at the circut board. there should be two red wires in the middle and a black wire in the right hand upper corner. you now need to detach these wire. the circut board of the motion sensor looks the same attach the wires of booth systems to their match. put the back on both devices, and set the motion detecter on top of the speaker. walk past the detecter or wave your hand in it and it will signal the speakers to turn on. the speakers will then signal the radio to turn on and to turn it off do it maually.
How do you test crank sensor on 92 Dakota 5.2?
The most simply way to check a crank sensor in any car is to get in car, turn key to start and watch tachometer (rpm gauge) if it shows rpms the sensor is good. If there is no tachometer then you will be in for checking wires. there should b a wire with 5 volts going into the sensor and with a test light if your lucky probe another and it should light up as the motor turns.
Where in the check engine sensor located on the engine?
There are sensors all over the engine that can turn the check engine light on.
Where is crank position sensor on 87 Mercedes 300e?
'87 M103 engine 300E. There is one sensor up front with a three pronged plug and there is one up back of the engine compartment under the oil filter. Just look for the head of the hex screw. Bit misleading because they are both referred to as crankshaft sensors or at least they were to me. Sorry I cannot give you more details but will clean this answer up a bit tomorrow with part nrs. etc.
-j
Where is the crank sensor on a 1991 Buick Regal - 31L?
THE CRANK SENSOR IS LOCATED ON THE PASSINGER SIDE OF THE ENGINE , BUT ON THE BACK OF THE ENGINE YOU MMUST REMOVE THE FRONT TIRE TO REACH IT RIGHT BEYOND THE SPEED SENSOR
No it's not!
It is located between the transmission and the engine block above the oil pan on the rear(since the engine is sideways)just about the middle of the car. It has one bolt holding it in and it is a little hard to get out, careful not to break the bolt
What are the symptoms of a faulty throttle position sensor 92 f150 4x4 EFI 351?
some sympons of a fault tps is tht it bogs out when throtel is opened quickly alot of the time it will only rev up to a sertant pint like it has a rev limeter on it other times it may be very slugish at the begining then all of a sudded it just gets the power back after the throtel is opened about 30% to 50% i hope this helps you out
"addtional info" to see if the problem is the tps disconnect the sensor. If you have the same idle your sensor has gone or is going bad.
Where is the throttle control sensor on a Pontiac Bonneville?
I have a 94 it is located rigt above the thermostat it has a plug in it with 3 wires coming from it it is not to big you would need a phillip that looks sorta like a z it has two screws in it. it is above to the right of the thermostat. I just replaced mine. Schelithea "Chics Rule" I have a 94 it is located rigt above the thermostat it has a plug in it with 3 wires coming from it it is not to big you would need a phillip that looks sorta like a z it has two screws in it. it is above to the right of the thermostat. I just replaced mine. Schelithea "Chics Rule"
Is a BMW and rover 75 diesel crankshaft pulley the same?
Yes, i believe the rover 75CDT and CDTI diesel engine (called M47R) is the very same as the BMW E46 320 diesel engine (called M47). This BMW engine was also used in the BMW E39 520 diesel car
This information is available on WIKIPEDIA.
Regards
Tommy
Where is the crankshaft positioning sensor located on a 1997 vw jetta gt?
Weird location, But it's just behind Oil filter. Probably if you get ubder the car you should be able to see it.
Could a car accident cause crank sensor to go badon olds intrigue 2002?
Yes........ depending how bad and where. front hard.... more than likely.
Locating crankshaft sensor for 1999 Chevy blazer?
The crankshaft sensor on a 1999 Chevy Blazer is located on the bottom of the engine, near the oil filter. It connects to the vehicle's computer and constantly updates it on the crankshaft's position.
you should call MINI USA with this question...I do not have the number on hand...but call a dealer and they can give you the 1800 number. Best of luck!
