0
Honda Prelude SI
The Honda Prelude SI was introduced in 1985 with a 1.8-liter engine, but was released with a two-liter engine in Europe a year later. The 1991 model sported a 2.3-liter engine that featured pop-up headlights.
794 Questions
Change Honda Prelude fuel pump?
In newer models - you can get to it by lifting the backseat cushion, detach the wires and you can easily remove the fuel pump and replace with the new one. Older models - has to be done by a shop because the have to hoist the car and drop the whole fuel tank to get to it. Hope this helps.
How do you make a Honda activa faster?
By using .. 'K & N' filters as well use 'SUPER' petrol from Shell.. its will give u better pick up and speed ... my bike touches around 95km/h..single and double around 90km/h..!!
How do you replace thermostat in 1989 Honda Prelude?
do this only after you have not driven the car for 3-4 hours to let the coolant drain and cool..look for the upper radiator hose on the block. there will be a dome shaped object with 3 brackets that the hose runs into. u will need a 10mm to remove the two bolts across from each other. remove thermostat and replace with new one and gasket
What is the firing order for a 1991 Honda Prelude si 2.0L?
the firing order is 1,3,4,2 on the distributor, the second connection going to the front of the car is 1, the fourth connector is 3, the fifth is 4, the first connector is 2, the center one is the coil.
yes
Where is the fuel hose Honda Prelude?
look next to the intake and you will see a metal line about 3/8 to 1/2 inch in diameter usually running down underneath the firewall. typically it will fit into a rubber line and run back to the fuel tank
How do i fix a low idle on a 1986 Honda prelude 2.0 si?
my Honda prelude 1986 si wants to cut off after its warmed up . any sugestions on what ot could be
Why would there be a clicking sound by your rear tire after its been driven and turned off?
if it has an electric antena and a broken cord so it wont pull down it could click
Where is the ECU located on a 99 Saturn SC2?
It is located under the dashboard on the driver side, close to the door, but you need to uninstall the top of the dashboard first to get to the bolt that is holding it in place in the bracket. Once you take off the top of the dashboard and release the bolt, the ECU comes down towards the floor of the car...
What does a bad lifter sound like?
a tapping sound from under the valve covers at any eng.speed. some eng. have adjastable valves but I sugest you use a repair manal for you car type or have a good mecanic do it for you
Where is the computer located on a Honda Prelude?
I have an 88 Honda prelude and my computer is located under the carpet on the passenger side.
Why is your 1990 Honda Prelude si over heating?
An engine can overheat for any number of reasons. Start by making sure your coolant system is up to date and well maintained.
Where is the oil filter located on a 1988 Honda Prelude SI?
the oil filter is located on the back side of the block in the middle
Where is the condenser fan relay located on a 1992 Honda Prelude?
It is bolted to the driver's side front of the engine bay right near the AC Dryer. There are two relays there one for the AC Clutch and one for the condenser fan.
If you are talking about a Prelude, here you go. http://autorepair.about.com/library/firing_orders/bl-fo-14844.htm
Where is the ecu located on a 1995 frontera?
The ECU is behind the center concil under the rario. it is mouunted in a thatcham bracket. the center concil and radio suround has to be removed to access it.
the imobiliser ecu is mounted behind the OS knee blocker below the steering wheel.
It depends on engine type.If you have a B20a5 you are getting about 135 hp at the flywheel and around 125 lb-ft of torque. Or most likely you have a B21a1 which puts out 140 hp at the flywheel and about 135 lb-ft of torque.The B21a1 is generally recognized as one of hondas worst motors.They were experimenting with the B21a1 when they put them in the third gen preludesand it didn't work out very well as Honda switched to the H series in the fourth gen ludes.The B21a1 engines are known for burning oil later in their life.This is due to the increased piston travel that wears the rings over time.In general the early B series engines are not great engines but can be reliable and can last long if properly maintained.But they have almost no potential for racing if that's what you wanted to know.The only option there is to build it up and turbo it which is very costly.I hope this helped you.
Gday mate. I have just repaired a later model vectra with the same problem. it had a dry solder join on the printed circuit of the dash board. you need to remove the instrument cluster and dismantle the cluster this can be tricky if you haven't got experience in this sort of stuff. the fault is in the connection for the ribbon to the circuit board.
How do you replace an oil pan and oil pan gasket on a 1996 Honda civic Lx?
I bought a 98 Civic. At the same time I bought the $185 service manual (because I thought it would pay for itself over the many years Hondas go).
I highly recommend having a torque wrench at your disposal to perform this procedure. Hondas go forever if you take care of them, a torque wrench is a small investment (and some auto parts stores will loan/rent them to you).
According to the manual (for the 1998 - the 1996 is probably the same) you will first need to remove the transmissioin/engine stiffener. This is a piece that transverses from the engine to transmission and is held in place by 4 bolts.
After that you remove the existing oil pan.
You must scrape off any residue or remaining gasket from the engine block - you can do that with a putty knife. Be careful not to scratch/gouge the surface. Then clean the surface of the engine block.
Get a new pan and gasket. Use gasket seal (Honda part # 08718-0001 ir 0718-0003) to afix the gasket to the pan. According to the manual, after affixing the gasket you should use additional gasket seal at both of the short ends of the (more or less) rectangular outline of the pan/gasket (including the rounded corners) and then put them on to the block (do this within 5 minutes of applying the gasket seal). The manual indicates you should hand tighten six bolts - the ones at the corners of the short ends of the rectangle, and the ones right in the middle of the long ends. When these are hand tight you will insert and hand tighten the other bolts. Then increasingly tighten the bolts starting with the one most directly under the oil filter. Work from that bolt clockwise, gradually increasing the tightness of the bolts until you reach a torque of 8.7 foot pounds.
If you don't do this correctly you will warp the pan, so be careful.
Once completed you should refasten the engine stiffener. The bolts going to the engine side should be tightened to 17 foot pounds, the bolts to the transmission side should be tightened to 33 foot pounds.
You should be done, but the manual says to wait 30 minutes prior to adding oil.
Good luck!
Warning: There is no way you can take out the oil pan on 96 Civic w/o removing exhaust pipe. And removing this pipe is a major pain as the bolts holding it are all rusted.
