0
Chevy Avalanche
Chevy Avalanche is a sport utility truck produced by General Motors that has five or six seating capacity. It is distinguished by its removable rear window and back seat open bed which can be opened via a folding panel.
1,380 Questions
Your local auto glass shop will have a replacement glass that goes on with double sided tape, it even has the "objects are closer" on it. You just carefully remove the old glass and stick on the new glass
Which one is the fuse for the backup lights?
Should be same fuse as turn signals look under hood at fuse panel on drivers side beside battery under black cover. Under the cover will tell you which one it is.
How much horsepower can you get out of a Chevy 305 1978?
How much money do you have? The 305 Chevy is not a good starting point. You would be much better off finding a good 350 and work with that small block. The power is only limited by the amount of money you want to spend.
Will an ATV fit into a 2004 avalanche bed?
It most likely will if it's a sport ATV. It most likely will NOT if it is a utility ATV because the rails that support the 3-PC hard cover make the bed too narrow. This is actually the reason that I got rid of mine and bought a Sierra.
How much horsepower does a 1991 3.1 v6 automatic have?
It depends on the condition of the engine, and how well its been maintained. A stock 1991 3.1L MPFI V6 was rated at 140hp, but private dynos over the years have show numbers as high as 152hp, depending on the make/model/condition of the vehicle. Several factors are attributed to hp loss/gain.
How much would a CFM56-5 engine cost?
I was wondering the same thing. I found a used, damaged non-airworthy cfm-56-3 for $99,000usd. I also found a used, airworthy, no hr. limit CFM-56-5 for $650,000usd. The CFM-56 engine family is very popular there were somthing on the order of 20,000 produced.
Where is bank 1 sensor 1 on an 03 chev avalanche?
On the catalytic converter, driver side, upper sensor.
Yes
How do you replace the seal on a water pump from 2002 Chevy Avalanche?
YOU DON'T!!! I have a 2003 avalanche and I had to replace the water pump you can't replace the seals!!! It's a defect in the 2001 to 2003 avalanche the seals fail.
What is the average price to replace a water pump on a Chevy Avalanche?
Called a local dealer today and informed that the cost is approx. $500. Not including hoses and belts, if you choose to replace. Found a new pump for $70.
Do aftermarket wheels require balancing If not how do you tell which wheels don't require balancing?
All wheels require balancing once the tires are put on, The wheel may be manufactured perfectly but its the tire that has imperfections and causes the whole assembly to need balancing.
How do you repair door on passenger side that want unlock?
I assume it is a GM car..I have several Cadillacs and they have all done this ... You have to remove the door panel (not very easy with the door closed, but it has to be done) reack your hand in toward the lock unit at the end of the door while getting someone to try pulling the lock up .... gently. Every model has a slightly different system, but it should be replaced. Check with a salvage yard and see if they have on for your car, once the door is open, it is quite easy to replace. Just libricate/grease it well before you install it. You might want to pick one up first, then you will know what you are reaching for. You don't need the lock itself (the key unit) you just need the mechanism and rods that actually lock the door. Best of luck.
2002 Avalanche rear window leaks carpet is always wet?
I had this happen recently, I was told my the dealership that it's is designed to get "some" water in the back, however there are drains and if they get clogged like mine did the rug gets wet, now the rug smells awful, I'm going to try to get it shampooed if not, I have to get a new rug.
How much horsepower does a stock 1987 Dodge Ramcharger have?
if it is the older LA block my guess is roughly 220-230hpType "1987 Dodge Ramcharger" in your browsers search window. You should get many possibilities. carsurvey.org cardomain.comM depends on what motor you have
Example, my 1990 dodge ram charger LX, with a stock 4 barrel carb, 2x4 tranny, 5.7 litre engine, was about 350 hp.
i have a 1987 dodge d100 with bone stock 318 60000 miles it has a sad 130 horse it runs good but no balls at all i put on dyno for the hell of it and thats what i got lolLess than 200 hp. After 1979, trucks under went the same de-powering as cars. Also in 1990 Dodge did not have a 5.7L engine. There was only 3 options: 3.9L V-6, 318 (5.2L) or a 360 (5.9L)
i take it u don't have a 90 ramcharger, i do tho, a 90 le150 4x2, a 5.7 isn't offered, in 90 they were throttle body injection, not carbs. my 318 5.2 pushes around 220
Actually- If your talking about the 318(5.2L) It came with about 156hp and I think @ 250ft lbs of torque. This doesn't sound like a whole lot but TORQUE is where a trucks real power lies. If your talking 360, Im not too sure but my guess would be not a lot more horse than the 318 but should be a fairly considerable amount more of torque... maybe 180-190hp and 280-300tq. btw... great old trucks!!!!
Location of 25932571 valve evap em 2004avalanche?
I don't know! I was hoping this site would tell me.
Where is the fuse panel flasher on 2002 Chevrolet avalanche?
The flasher module is attached to the bottom of the IP fuse block
How do you replace the starter on 2004 avalanche 1500 z66?
You need an 8mm or 5/16th socket or wrench to disconnect the battery... if you're small enough, you can get underneath without lifting up the vehicle.... me, personally, I can do that on the 4x4 models, but the 2wd models are a bit tight for me, so I lift the front end up on those... the three bolts that hold the starter in place use a 15mm socket, and the starter comes right out. Make note of which wires connect where on the starter... car starters are pretty simple and I usually only do this on Class 8 truck starters (which use multiplexed systems have many more cable going to the starter), but you might want to use a paint marker to mark the locations of the wires if you're unsure you'll remember where they go.... disconnecting the wires from the starter, I believe one nut will require an 8mm socket.. the large one, I don't remember offhand, as it's been some time since I've replaced a starter on a GM truck, but I believe that'll be either a 15 or 16mm socket.. either way, if you have a complete socket set, you'll have the right size. I'd recommend reattaching those cables to the new starter before bolting the new one back in.... by the way, you'll find the stater in front of the bell housing, on the right side... once it's all installed, you reconnect the batteries, start it... there's a possibility you might have to add shims if the starter appears to be missing or just barely catching the flywheel teeth.
And, of course, before you lift the vehicle, make sure you chock the rear wheels to prevent it from rolling. When you lift it, place it on jack stands.. don't just leave it sitting on a jack.
