0
Grand Am GT
The Grand Am GT was a rebadged fourth-generation model of the Pontiac Grand Am manufactured by General Motors from 1992 to 1995. The car featured a 3.3-liter Buick V6 engine, and a five-speed manual and three-speed automatic transmission.
1,619 Questions
Where is the fuel pump located on a 1998 Pontiac Grand Am?
Almost all fuel pumps are located in the gas tank.
How do you get a new shunt fuse for a 97 Pontiac grand am?
you cant get one you might be able to get it at a junk yard but good luck with that
What is the spark plug gap on a 1996 Pontiac Grand Am SE?
Listed in your owners manual and under the hood on a placard. Also when you purchase the new plugs the parts store can tell you the gap. They come pre-gapped and are usually pretty accurate. I would still check the gap.
Why would the internet stop working on one Windows account but work on another?
different firewalls, occasionally my wireless acts up and will disconnect from the internet and connect to the home network instead[i.e. printer]
How do you replace a c4 grand Picasso headlight bulb?
You can take off the plastic that is surrounding the original bulb. Then put in the new one and test to make sure it is working properly.
Where is location of front blower fan?
The blower fan motor is located under the hood on the left side in a Ford E150
Where is the fuse for 2002 Pontiac Grand Am GT?
The fuse box is on the very left side of your dashboard.The driver's door has to be opened in order to access it.The cover to the fuse box has a diagram detailing which fuse is for what accessory.
Assuming the drive belt is there and has the proper tension, my guess would be the power steering pump is bad.
Where is the tensioner for the serpentine belt on a Saturn?
The belt tensioner is located below and in front of the power steering pump. It is accessed easiest by taking off the passenger front tire, taking the plastic panels out and looking just in front of and above the alternator. Turn it clockwise to release tension on the belt, NEVER turn it counter clockwise as this will loosen the bolt that holds the pulley on the tensioner and will cause very bad things if it flys off while you are driving on the freeway...personal experience. The tensioner is held on by (2) 10mm bolts, and you will have to remove the pulley to get to them, just make sure you tighten the bejeezus out of the pulley bolt.
Yep, but not a whole lot. In electronic igniton systems, the "old fashioned" points and condenser in the distributor have been replaced with non-mechanical timing for the firing of the ignition coil[s], and thus the plugs. The method for doing this is a "Hall Effect" transistor pickup sensor, which is "triggered" by a small magnet[s] passing by it. Sorry I can't give more detail. j3h.
Motor turns over but won't start?
try to see if the battery is a little low. it happened once to my dad's 1990 miata. if not, then try to see if oil is low. then, if it still won't start, then try to take it to the dealership
How do you remove a pushrod from a harley?
Buy a manual. It will tell you how. You need to remove the heads.
*
*
You can also fabricate a tool that forks around the pushrod and rests on the cylinder base allowing you to lift the pushrod out of the tappet by slightly compressing the rocker arm - valve spring , same technique to reinstall it
I used a wide automotive drum brake star adjustment tool ( such as
Drum Brake Adjusting Tool -- KD 295 )and cut a deep notch into it, available at almost any automotive parts store
*
*
if you are going to install new adjustable EZ install rods then you can remove the old rods by simply snipping them with a bolt cutter ... yes this is how it is done
Is 5x114 same bolt pattern as 5x114.3?
Question
His a 4x114,3 fit on a 5x114.3 on a SUV .
Or what the difference between 4x114.3 and a 5x114.3
How do you change a 1999 fuel injector Pontiac gt 2.4?
I haven't changed injectors on the 2.4 engine, but I have changed them on a Sunfire 2.2.
I'm pretty sure that they are similar. What helped me, was having my Haynes manual for the car. I suggest that you pick one up.
The job is fairly direct and shouldn't take too long, once you get a grip on what's going on.
FriPilot
Okay, crank it. No start...are you getting fuel? If so, check for spark. If you are getting spark and fuel, check to see if your timing is correct. After that, I'm really not sure...if you are getting gas and spark, then the thing should fire up.
What are the stereo wiring schematics for a 2002 Toyota Celica GT-S?
2004 Toyota celica stereo diagram
How do you replace the powered driver's side mirror on a 96 Mazda 626?
The question you ask is too involved for a proper answer. You may want to go to a car parts store, or book store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
Where is the ac recharge port on a 1999 Pontiac grand am?
Low pressure hose follow- larger hose from a/c compressor In front of the firewall. Passenger side. Cap is blue (likely under the dirt) Hint: Do this when your engine is cold or you'll likely burn yourself since it's low down
Popping sound underneath car when brakes are applied?
Sounds like you need to replace your brakes very soon. You may need to replace hubs as well.
How do replace blower motor resistor on 1998 civic hatchback?
Remove your glove compartment. Look to the right side inside. Look for 2 screws, remove 2 screws. Lift up on wires, unplug wires from resistor. Plug in new resistor into wires. Screw the screws back in, reinstall glove compartment.
What needs to be repaired if you get the Code p0420 catalyst effeciency threshold low?
2000 HONDA ODYSSEY CODE PO420.WHAT NEED TO BE REPLACE? ANSWER XXXXXXXXXXXXXX Code PO420 is catalytic converter efficiency low bank 1, sensor1. You did not state as to the year,make and model of the car as well as the engine size. I am a member of IATN and the majority of there fixes was related to someone installing an AFTER MARKET converter. There is a big difference. I strongly suggest that you go to a repair shop with the proper equipment as well as a very good tech to diagnosis the problem. You could replace parts and never fix the problem.jd1709
This question can produce multiple answers, before you go any further try locating your starter relay located on the right side of the battery under a cover. this cover will give a diagram showing you where the relay is located. You can take the low or high beam relay and switch it with your starter and test both ways. (turn on high beams or headlight depending on swap, then trying to start this vehicle) If nothing happens then you can eliminate that and hook up a set of jumper cables to the battery and touching the positive cable to the starter. There will be a fat wire and a skinny wire the fat wire will be covered with plastic the skinny will have a plug that needs to be removed from starter. Where this plug is connected (on the starter side) touch the positive cable to the prong if vehicle turns over, you can eliminate a bad starter, then you can turn your key on and bump the starter again if vehicle starts you need a ignition switch or you need to check your wiring.
Where is the camshaft position sensor located on a 1999 Pontiac Grand Am?
What size engine? If the engine is a 3.4 litre, the sensor is located directly under the power steering pump. Power steering pump, must be removed before you can gain access to the camshaft sensor. I also removed the engine mount, to ease removal of power steering pump. Caution!!! (support engine with jack before removing engine mount.)
Where is the dip stick for transmission fluid on a 2001 Mercury Villager?
Just to the top left of the battery tray. Squeeze the release and then pull up the dipstick.
