0
Jeep Grand Cherokee Laredo
The Jeep Grand Cherokee Limited is an upgraded version of the Grand Cherokee, with leather interiors, alloy wheels, heated seats and mirrors, and remote keyless entry. It’s powered by either a 5.6-liter or a 4.0-liter V8 engine.
3,451 Questions
What is rattling in the rear end of a 2002 Jeep Grand Cherokee when you hit bumps?
check all 4 of your shock mounts
or check the stabiliser links
How do you fix a broken gas gauge on your 94 Sunbird reads full all the time?
If The Guage reads full all the time, chances are that it is toast. You'll have to replace the Gas Guage with a factory or aftermarket replacement. Auto Wreckers often provide a cheaper alternative, if you don't want top buy new. Honestly.......Give your gas tank a kick! The float in the tank might free up for awhile.
MY 94 3.1 V6 HAD THAT PROBLEM THE DIFF WAS THAT IT READ ONLY UP TO A HALF OF TANK. WHAT FIX IT WAS IN THE BACK OF THE TANK THERE ARE TWO PLUGS PULL BOTH OF THEM OUT THEN SWITCH THE KEY TO ON YOU WILL NOTICE THAT IT WON'T READ GOOD OK THEN BACK TO THE PLUGS AND PUT THEM BACK IN. TURN THE SWITCH ON MORE TIME AND THAT WORK FOR ME.... HOPE IT HELPED
Where is the emergency fuel switch on a 2003 Jeep Wrangler?
Answer.
There is a roller over valve on the fuel tank that will stop fuel flow if the vehicle turns upside down. Other than that, no emergency fuel cut off swtich. What kind of problems are you experiencing?
Where is the fuse for a 1993 jeep Grand Cherokee Back up lights?
On a 93 it would be #4
It is on the same circuit as the brake lights, but if they are not working, and the bulbs are good your switch needs cleaning or adjustment.
Attempt this first since the switch costs nearly $300 bucks.
On the passengers side of the trans just behind the bell housing there is a fan shaped switch, loosen the 12mm bolt ( smaller of the two, and rotate the switch while a friend checks the lights. this problem is usually accompanied by an occasional inability to start the vehicle, but can be cured by jiggling the shifter.
While adjusting the switch make sure that the vehicle will start in park as well, remember to block the wheels while testing the back up lights, engine off, key in run but not start, shifter in reverse, move switch until lights come on.
Once you find this spot, hold it in place and have your helper check to make sure it will start. This may take several tries to get both working correctly.
If you have no luck the switch may be dirty, this happens a lot. Hold the post to the bottom large bolt still while you loosen the nut, then remove it, then remove the 12mm adjusting bolt on top, remove the wire connector and pull the switch away, remove the bolts on the switch and separate the halves, use electrical contact cleaner and maybe some q-tips to clean all the copper connections completely apply di-electric grease and reassemble, refit to the trans and readjust so all functions work, this switch controls back up and start safety.
Caution! always hold that bottom bolt while tightening the large nut, this is connected to the gear adjuster and you could damage the internals if it isn't secured while you do it.
How do you unlock a 2005 Chevy Tahoe with keys locked inside?
Don't they come with "ON Star" for the first year? Otherwise, call the local police department. They often carry the tools necessary to get into a locked vehicle. If that doesn't work, call a locksmith.
Call AAA, or other automobile club or lockout service.
How do you unlock the steering wheel for a 1988 mercury grand marquis?
Try "rocking" back and forth while turning ignition key
What would cause a popping noise in right side rear end while backing or braking?
Likely a loose or broken strut or shock. Could be the same for a load leveling bar, depending on the vehicle.
Where is the reset switch for the fuel pump on a 1997 jeep grand Cherokee?
Jeep doesn't use inertia/reset switches
Jeep doesn't use inertia/reset switches
I was able to get my lift open by sticking a long, skinny, flathead screwdriver up between the latch and the body. Once it was in I slid the locking mechanism to the right. I got the gate open and was able to get the panel off and temporarily repair the latch.
What does perform maintenance mean in the information center on a 99 jeep?
It means that there are certain maintenance items that needs to be done at this time. Each time the odometer reaches a set factory mileage, it trips this light notifying you that something needs to be done. Look in your owners manual to see exactly what maintenance you should perform.
ANSWER I have a 2000 Grand Cherokee and wondered the same thing. In my vehicle, it is a user set function. You can set it to go off at various intervals to remind you that something is due. I have it set for 3,000 miles to remind me that the oil change is due. It can also be reset by me. As the last poster stated, see your user's manual.
Where can you get a fuse diagram for a 1998 Jeep Cherokee?
Consult your owners manual, Factory Service Manual, any of the Cherokee owners Forums (CherokeeTalk, JeepForum, NAXJA), or use your Internet Search function.
You can also spend $10.00 on Mitchell on-Demand for your Jeep. It is good for 1 week. Copy everything you need and save for reference, best deal in town or get it for 1 yr for $35.00, that's what I did for mine.They are a sponsor for this site, we used it in electrical shop I was at............good luck, Mike
How do you fix backup lights on 1998 Jeep Grand Cherokee if bulbs burn?
My problem is the same, but with a different car. After doing a little research, evidently one should check the fuse for the lights, and if that isn't it, then check a switch on the side of the transmission with some wires going to it. Sorry I don't know more. Good luck.
What would cause quick flashing on only the right turn signal on a Jeep Cherokee?
Check two things: 1) the fuse for your flashers/blinkers and 2) that the bulbs are good still.
Will 31x10.50 tires fit on a stock 1995 Jeep Grand Cherokee Laredo?
I put them on my 95 JGC 4x4 stock but they will rub when you turn. I put 2" spring spacers on mine and that took care of the problem.
Make sure you have the proper viscosity of oil. 5W30 is what the specs are for a 4.6L engine.
AnswerYou have a serious problem here. Don't continue to drive this truck in this condition. Severe damage is being done in these 2 minutes. Your oil pump may be failing, or you may have a bad filter. Change filters to a Motorcraft filter immediately. If this does not cure the problem, have this looked at by an expert. AnswerI echo the previous, serious engine damage is likely to follow, would also suggest a stuck oil pressure sending unit. (Easy screw in replacement) try that first, but if it's still acting up, TOW IT IN.2008 Escalade the lift gate will not open?
The lift gate won't work if the glass is open. Sometimes it is open but not obviously so ... I would suggest opening the glass, slamming it shut ... then try the lift gate again.
If it's rear wheel drive it could be a U-Joint going bad. If it's front wheel drive it could be a CV joint going bad. That's just a guess since I can't hear the car.
Change the blinker bulb for that side. It is a hit and miss though. If you change the front bulbs and it still doesn't blink you will also need to change the rear bulbs. The front bulbs are rather difficult to change from above the vehicle. You may want to get underneath and definitely during the day!!! THE REAL ANSWER!!!!!! This drove me crazy on my daughters car. It turned out to be the day time running light modual wich is located behind the radio. the conections were loose. when you turn on the right turn directional the front light would go out but the rear directional would work. listen closley behind the radio for a one click noise when you activate the right turn, and also a delay one click when you deactivate.
http://www.instant-radio-code.co.uk/chrysler-jeep-code-search.php
How do you replace the top brake light for a 2004 Jeep Grand Cherokee?
Rear: Brake, Back-up, Tail, Turn signal (3 bulbs, all # 3157)
To access the rear bulbs, open the liftgate and remove the two Phillips head screws from the side of the housing as shown in the center photo above. Slowly and firmly rotate the assembly away from the vehicle until it disengages from the ball pin socket that secures it in back.
Each of the three light sockets, all containing the same exact bulb type, can be removed by turning them counter-clockwise 1/4 turn.
Taillight harness connector
To remove the taillight harness, slide the red lock tab up and pull connector off.
What is the average temp of a running engine?
Anything from 180 deg F to 230 deg F. Newer engines are designed to run warmer than in the past.
