0
Toyota SR5
Manufactured by Toyota Motor Corporation, the SR5 (Sport Rally 5-Speed) belongs to the Hilux pickup truck product line. The Toyota SR5 was a popular option package in the North American market.
941 Questions
How long would you have selpt if you went to bed at 940 pm and woke up at 700 am?
so 9:40 p.m + 20 minutes equals 10:00 p.m. 10:00 p.m + 2 hours equls 12:00 a.m. And 12:00 a.m + 7 hours equals 7:00 a.m. so 2 hours + 7 hours equals 9 hours. And 9 hours + 20 minutes equals 9 hours and 20 minute that's your answer .
1994 Mazda B2300 ABS light will not go off how do I troubleshoot this?
Did you try disconnecting the positive battery terminal for a minute then reconnecting it? Soemtimes this will reset the computer and the light will go out.
Inspect the driveshaft, look for dents, undercoating or buildup, or driveshaft or companion flange out of balance, check for missing weights on shaft. Try removing driveshaft and reinstalling 180 degrees different.
How do you remove the wheel hub Front on a 2000 Ford Windstar?
Try this:
I have a ford 1992 windstar and there was a 4th bolt that i didn't see at first. Try looking at it from different angles.
What would make a pickup coil in the distributor go bad twice?
I fixed the problem it was the air gap.
Ok, the AC takes several horsepower in order to operate. Rather obviously you can't extract energy from nothing, ie.. the AC does not run for free! Turning on the AC causes the drive solienoid to engage the AC clutch which, in turn, puts an added load on to the drive belt. You are hearing the engine speed-up to counter the engagement of the AC clutch, so as not to kill the engine. You will hear the noise generated from the AC compressor when it is engaged. you will probably hear noise, from time to time, from the fan belt...the serpentine belt which runs all over the place in front of the engine and drives the radiator cooling fan...at least in most cases...but you could have an electric fan or both. In any event, this too drives the AC compressor. Belts sometimes squeel because they become dirty, uncommon with modern vehicle like a 1994 model, and they needed to cleaned. It is a good idea to give the belt pulleys some lubrication from time to time as this will prolong the life of the bearings and you won't have little strange noises generated that seem to come and go. Hope this is helpful, and don't worry so much about the bizzare little noises which sometimes are generated from under the hood. If they become loud then you need to do something to find and correct the problem. Vehicles are alot like people in that they have their various quirks, and in that failures are usually the result of many combinded failures that add up to one major heart attack! Change your oil every 3,000 miles with a new filter and you will be motoring along for a good 200 thousand miles easily.
How do you program a 2006 tundra key fob?
Start with key out of the ignition, driver door is open (all others closed),
and driver door is unlocked. # Insert key into the ignition (don't turn it) and pull it out # Perform these steps within 40 seconds: a. Using the power lock switch on the driver's door, perform 5 lock/unlock cycles with lock.Use an even pace and try to go about one cycle per second. 1 cycle = 1 lock and 1 unlock) b. Close, then open driver's door. # Perform these steps within 40 seconds: a. Using the power lock switch on the driver's door, perform 5 lock/unlock cycles starting
with lock.
Use an even pace and try to go about one cycle per second. (1 cycle = 1 lock and 1unlock) b. Insert the key in the ignition cylinder. c. Turn the ignition to ON (as far as you can without cranking the engine) then back to OFF
d. Remove the key from the ignition. # Within 3 seconds, the power door locks should cycle automatically indicating successful entry
into programming mode.
Return to step 1 if the locks do not cycle at this point.# Perform these steps within 40 seconds: a. Press the lock and unlock buttons on the transmitter simultaneously for 1 second. b. Immediately after letting go of the lock and unlock buttons, hit the lock button by itself and
hold for 2 seconds. Within 3 seconds, the door locks should cycle once indicating successful
programming.
If the door locks don't cycle, or cycle twice, repeat steps a and b-your remote has not
been accepted. c. Repeat steps a and b in step 6 for each new transmitter. 7. Close driver door.
Where is the location of a thermostat on a 22r engine?
In between the valve cover and intake manifold. Towards the front of the motor. You see your upper radiator hose goes right to it. You'll have to remove the hoses that go from your valve cover to the throttle body to access it.
What is the towing capacity of a 1995 Toyota 4runner?
From Autobuyguide.com (http://www.autobuyguide.com/1995/12-aut/toyota/4runner/reviews/index.html).
"Toyota rates this vehicle's towing capacity at 3500 lb. We don?t question this, but we do think that towing a 3500-lb. trailer would require some patience. If you have a log of medium-heavy towing planned for your new sport/ute - say, 2500 lb. or more - this may not be the right vehicle for you."
I tend to agree. I have a '95 3.0L V6 SR5 4WD and towing a 3,000 lbs. pop up I borrowed from a friend was dragging it down HARD through the mountains of Colorado.
How do you change a thermostat in a 1986 Toyota pickup?
From the radiator follow the top hose to the engine. It will connect to fitting that is about 8 inches long with a rounded end on it as it bolts into the engine. THis is the cover for the thermostat. Remove a couple of vacuum hoses to gain access to the nuts, and remove them. Lift the whole thing off and tuck it to the side. You should see the thermostat. Remove it and then clean the area prior to insalling the new on. Orient the new one the same way the old one was and reinstall in reverse order.
Where is the starter on a 1993 Toyota pickup?
On a 94 4X4 you can see it looking under the passenger front wheel well at the lower rear end of the engine.
Where is the PCV valve at on a 2003 expedition?
Standing in front of vehicle PCV is located on the left side of engine valve cover to the rear of engine, hose runs along the back of engine. Hope this helps.
Why is there white smoke coming from the dipstick tube and the valve cover on a 89 ford F150 4.9L?
excessive blowby
Where is the PCV valve for a 1990 LeSabre?
The elusive PCV valve does not leap out at you on the '90 LaSabre. Since, if your engine and it's spark plug wiring wiring is configured the same as mine, and hopefully it is for the sake of this answer, the PCV valve is hidden beneath those wires and, mostly, is further camouflaged by oil. Anyway, here's how you find the little sucker: As you stand next to your left tire, looking into the engine compartment, follow the 3 rear spark wires, from rear to front, ABOUT 3 inches PAST the REAR rocker arm cover. Pull the wires aside and look down a bit. There, at what might be called the south-west cornor of the rectangle engine block, if you consider the way you are facing to be "north", is the PCV valve. It's real close to the engine block. It fits stright down into its gromet with the hose the conects to the top/plactic part of the valve being only an inch long.
How do you gain access to the rear speakers in an Alero in order to swap them out?
pop the speaker grilles upwards in the front and slide them towards you. then there are four plastic clips in the corners of the speaker that can be gently pryed back and it will come out. dont forget to unhook all four wiring clips underneath by lying in the trunk.
What horsepower a Toyota 22R engine have?
The Cressida had a 2.4-litre
22Rengine producing 108 horsepower
Difference between 22r and 22re?
The 22r is carburated. The 22re is fuel injected. I believe that is the only difference.
Check your codes I had a similar problem and it was solved buy replacing the MAP sensor
Where is the PCV valve on a 2005 Chevy uplander?
The 2005 Chevrolet Up to land or PCV valve can be found near the back of the engine. The PCV valve will be behind the air cleaner housing.
A vehicle speed sensor (VSS), which is attached to the transmission, sends electrical pulses to a central location. From there the signal can be shared by whichever modules need it, speedometer, transmission, etc. In your case the destination is a little plastic box called a Digital Ratio Adapter Controller (DRAC).
