0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
Chevy Chase's first guest on his ill-fated talk show was his co-star from Foul Play Who?
His mediocrity can be forgiven since this was his first major foray Goldie Hawn gets much more screen time than Chevy Chase
How do you change injector on 5.7l?
unfortunetly they dont have individual injectors they have a spider injector system which you have to remove the upper intake plenum remove the whole system and replace. they also cost upwards of 300 dollars at a dealer. not sure if they make them after maket either. hope this helps
What math skills do you need to be an auto mechanic?
This might answer your question: http://answers.yahoo.com/question/index?qid=20070929201221AAN2qPA
Where is the oil pressure switch in a Chevy Blazer?
If the engine is the 4.3, it is located under the hood, on top of engine, way in back, on the drivers side under the distributor.
Will a 22x9.5 wheel fit a Tahoe?
Claro ke si!! I have an 08 I just bought and I just put some on it. The only thing is gas!! If you want some good deals on wheels hit me up! paintpaint @ hot mail . com Hope this helps.
No, unfortuently there are not any engine kits that I have seen avalible for the z31 300zx.
AnswerNot that I know of. Why would you go through all the work of putting a 350 in a Z31 when the VG30ET is said to be able to handle 400-500 horsepower stock and 500+ rebuilt?Some reasons i can think of
availiblity of parts
cost of parts
aftermarket support
repair costs
swap cost
Although there is no kit, it would be fairly easy to install a small block in your Z31 ( which I'm assuming is N/A ) .
Issues that would arrise
oil pan clearance
Mounts
Rear end would need to be replaced ( oem rear ends aren't worth **** )
Custom Drive shaft
other small issues
I'm consindering a 350 in my 88 z31 n/a 2 seater . With a fair amount of knowledge of SBC's , i think this swap would be pretty straight forward , hardest part being the crossmember issue and wiring the ignition
ahem,
LS1 & transmission.
stand alone managment.
upgraded fuel pump.
upgraded fuel lines if it bottle necks (which it probly will)
engine and transmission mounts.
larger radiator (for the obvious reason)
and about the diff. weld it shut. it will last if you don't get serious traction off the line.
done.
good way to spend 12,000k.
6-7 for engine.
3-4 for and parts.
2-3 for labor.
about the VG. you are either HIGH if you honestly think that after a rebuild a VG will handle 500horses with boost reliably. or you have gratuitus amounts of money falling from your butt. 500 hp on a V8 street driven is too much for the street. and the torque you will create with an LS1 is driver friendly and easy to drive. you won't have to wind up the LS1 like you will with the VG. because the VG's torque will all be where the boost is, and we all know boost takes time. something we all are against.
How much does a small block Chevy weigh?
ACCORDING TO http://www.enginefactory.com/chevdimensions.htm 575 LBS
What oil is recommended for Arizona heat 100 plus degrees f?
The same as for the rest of the country. Exactly what is written in your owner's manual.
How do you time a 1986 chevette 1.6L OHC engine Help?
How do you determine and engine's bore and stroke?
if standard engine, you could pull specs for engine online, or any dealer of that vehicle could tell you. should also be in owners manuell if you have it
Could be a few things. are both sides getting red or just one? If both sides are check exhaust for restrictions and your timing if one side check the valves for some staying open on power stroke letting combustion leak out the manifold. Might be a cracked head maybe???
What trail at Battelle Darby Creek Park is that old rusty 1952 Chevy truck on?
When I watched this video from a man at Battelle Darby Creek Park on a walking trail he found an old 1952 2-door Chevy truck lying on the side of a trail
Where is the idle on a 4.3 6 cyl vortec?
The idle is adjusted by way of the Idle Air Control motor as directed from the Engine Control Module.
The idle is computer controlled.
I changeTHE IAC motor for a new one ,still there is a bit of a rough Idle, what can be the trouble
What make the van run sluggish?
it could be many things, start off with a good tune up and go from there.
What kind of engine oil do you use in a 1997 one ton GM 7.4 Vortec 454 gas engine?
15/50 summertime 10/40 winter
Where do you put antifreeze in a Chevy Equinox?
you dont! you use that dextron cool crap that is pink and you add it to the reserve well
There is a special easy out for this. If it cant be used or the remains of the plug still wont come out then the head will have to be removed and the spark plug removed from the inside.
A machinist may be better suited to do this if you end up having to take your engine apart.
It is a RPO code for GM full size 4x4 trucks, which usually include stripes and decals, beefier suspension parts, skid plates, larger tires/rims, etc.
What does the right side hitter do?
They hit behind the setter and usually come as a surprise hit. They hit cross court or line kills. And they can be a setter also.
What year is the engine for casting number r90209802?
Maybe this will help you. I hope so. http://www.migweb.co.uk/forums/vauxhall_archive/t-204070.html FriPilot
Where is the air cabin filter located on a 2001 Chevy Metro LSI?
You won't find one. It didn't come with a cabin filter.
