0
Ford Escape XLT
The Ford Escape XLT is an all wheel drive, compact crossover sport utility vehicle (SUV) produced by the American automaker Ford Motor Company. This vehicle may be powered by a 3.0 L V6 flex-fuel or 2.5 L 4-cylinder engines.
2,580 Questions
How do you replace the headlamps on a 2004 Ford Escape?
First, with the keys NOT in the ignition, POP THE HOOD, and prop it up on the rod.
Right where the headlight is, on the inside of the engine compartment (you just look on the inner side of the headlight, an obvious and easy place to locate) you will see a rubber cap with a plug going through the center of it. Remove the plug by simply squeezing the sides, lenghtwise, gently and sliding it straight off. Once it is off, you remove the rubber cap completely, simple to do because its kinda fitted but loose enough to just peel off.
Now, here is where the only tricky part is; MAKE SURE YOU HAVE THE CORRECT BULBS!! 9003xvbp There is a spring-type clamp that holds the bulb in, which you will need to squeeze together and push down to get them out from under the little hooks that hold the whole thing in place. once you have that part free, you will feel the bulb loosened up and able to be pulled directly out. Replace with new bulb, which fits back in just like a puzzle piece as the last one did and reclamp the hooks, put the rubber cap back on and plug in.
You can remove the whole assembly in you need to. If you are unlucky enough to have to replace the corner lamp, or have a great deal of trouble working on the headlamps in the amount of space you have under the hood, you can remove (2)-10mm bolts that hold the top of the bumper/grill assembly on. then go to the wheel wells, and turn the tire att the way to one direction and remove the (3) plastic, Phillips centered clips in the front of each wheel well. With just those (8) things removed, you can pull the bumper awat enough to remove the (2) hidden 10mm bolts holding in the bottom of the headlamp.
If your lights are wet inside, I'd leave them out in the sun for a day, apply silicone around the factory seaed area and it wouldn't hurt to silicone- moderately- the new headlamp bulb after you put it back in.
How do you turn off interior lights dome and floor in 1993 ford tempo 4 door?
First shut all the doors then use your light switch to turn off or on dome lights if that doesn't work it could be a bad door pin switch
stock s-10 with 2.2 is 120 hp and 140 torque that is the enigne not the whp!
What is Error code p0303 on 2003 ford escape?
It is a cylinder misfiler on cylinder #3. Many times it is a defective coil-on-plug (COP) but not always
What is the difference between 265 75 r16 to 255 70 r16 in tire size?
Allot of difference. The 265/75-16 is 5.03% 1.59" larger in overall diameter than the 255/70-16 and is a narrower tire. These 2 sizes are not interchangeable.
1990 astro front all wheel drive not working no noise back is fine Help?
there are only two items to check here; transfer case, and the front differential. both expensive. To test, lift all four corners on jackstands, put vehicle into neutral, spin front tires and listen; ANY noises from front indicate bad front diff ($250 from boneyard). Next, to check transfer case;start engine/put into gear. An AWD unit 'floats' power to both front and back, like a diff. And are notorious for failure in two ways- one, they seize sending 100% to both axles, and will blow entire drivetrain. two is your symptoms, no power output to (front) axle. There are clutches inside...like a mini-bike!!! LOL AWD transfer cases are $$$$ ($800 & up At junkyards-$1400 new). I solved this problem by converting to 4X4. I swapped out parts from an old blazer s-10..(transfer case-4x4 shifter unit-front differential-front driveshaft- vacum parts/pieces. and it all BOLTED TOGETHER. driveshaft 's-10' had to be 4.5" longer.. had to 'modify' a brace under floorboard with hammer/torch for new transfer case to fit. that was 60,000 miles ago, without so much as a burp. good luck.
there are only two items to check here; transfer case, and the front differential. both expensive. To test, lift all four corners on jackstands, put vehicle into neutral, spin front tires and listen; ANY noises from front indicate bad front diff ($250 from boneyard). Next, to check transfer case;start engine/put into gear. An AWD unit 'floats' power to both front and back, like a diff. And are notorious for failure in two ways- one, they seize sending 100% to both axles, and will blow entire drivetrain. two is your symptoms, no power output to (front) axle. There are clutches inside...like a mini-bike!!! LOL AWD transfer cases are $$$$ ($800 & up At junkyards-$1400 new). I solved this problem by converting to 4X4. I swapped out parts from an old blazer s-10..(transfer case-4x4 shifter unit-front differential-front driveshaft- vacum parts/pieces. and it all BOLTED TOGETHER. driveshaft 's-10' had to be 4.5" longer.. had to 'modify' a brace under floorboard with hammer/torch for new transfer case to fit. that was 60,000 miles ago, without so much as a burp. good luck.
Where does the wiper fluid go for the back windshield on a chev venture van?
In the same reservoir as for the front. If you are not getting fluid to the back window, the rear pump may need replacing. The pump for the rear is high on the tank so keep it full and that may be your answer.
Where is the horn relay located on a 96 crown Victoria?
The horn relay for a "96 Crown Victoria (police model) is located on the right fender where the fuse/relay box is.....3rd relay in from the right. If you are on the right side of the car.....3rd one towards the engine.
Why does the Brake light on a Ford Escape stay on?
Actually, the ford escape has a factory recall on the ABS. (anti lock brake system). Take it to your ford dealer and they will fix it for free.
Low brake fluid
What is the humming noise coming from the front wheels of a Renault Scenic?
posible chance of wheel bearings worn. jack car up & rotate wheels check for excessive movement (grip wheel top & bottom try to rock)hope this helps. steve.
There are three 10 mm bolts that hold the headlight assembly in. Two are visible on the front side of the headlight assembly when the hood is up. The other is below the light assembly where the back of the light assembly meets the fender. It is accessed from the front and will require a socket extension.
Once the bolts are removed, gently pull the headlight assembly forward. You will see two long plastic pins on either side of the assembly. Pull the light assembly forward until they are clear of the holes. You should now be able to swing the assembly out far enough to reach the directional bulb socket. Twist the back of the bulb assembly about 45 degrees and then pull the bulb assembly out of the socket. Replace the bad bulb, ensuring that you do not touch the bulb with your bare hands and leave oils behind, which will damage the bulb once it gets hot.
Reassemble in reverse order.
Where is the low coolant sensor on a 2001 Ford Escape XLT V6?
It should be on the bottom of the coolant reservoir. The container is held in place by two bolts. Remove the bolts and disconnect the sensor cable on the side of the container, then it should just lift out
How do you change the fog light on a 2000 Pontiac Sunfire GT?
You will have to get to them from under the car. Jack the front up and secure it with jack stands. Don't forget to brace the rear tires from rolling. When you look up you should be able to look up and trace the wire to the light.
How do you change the serpentine belt on a 2000 Buick Regal?
depending on if it has the 3.8L or the 3.4L engine. first locate the serpetine belt diagram. or belt routing diagram, if it doesnt have one draw your own. then locate the tensioner which is usually a pulley connected to a moveable arm. place a 3/8" ratchet into the designated hole on the tensioner arm and turn the ratchet as if it were a bolt. if it doesnt move fairy easy reverse the direction of the ratchet. if it still doesnt turn you may have a seized tensioner. (which is fairly uncommon) remove the old belt and replace the new one with the correct routing. the routing is very important you don't want things spining in the wrong direction. check to make sure the belt is in all grooves and on all pulleys, if so release the tensioer and start the car.
How do you change the serpentine belt on a 1989 Cadillac Eldorado?
How Do I change the serpentine belt on a 1989 Cadillac Eldorado ?
How difficult is it to replace the alternator and oil pan gasket on a 2001 Saturn SC1?
The altenater is hard if you dont know what your doing I know just did it to my car you need to go under the car and find it and then take off the belt then undo all the bolts to the alt. and wireing make sure the battery is unpluged first .then when all that is done put it back the same way you took it off.
Where can I get a diagram on a 2001 Chevrolet Impala intake manifold?
You need to purchase a Haynes Manual that is for your particular car. You can get it at a bookstore or a parts house.
Front license plates weren't always required. If you purchased a car before the law passed requiring front plates, you don't have to have them on that car. I know from personal experience they will sometimes issue a ticket for that and the ticket is invalid.
How do you change a light bulb on a Toyota yaris?
Take a flat-head screwdriver and pry off the plastic panel on the respective rear side. It looks like a vent.
The brake light is the one at the top. Twist the bulb holder toward the outside of the car (counter clockwise for the left bulb if you are facing the rear, clockwise for the right.) The first time I did this it was sticky and took a bit of effort. Then pull the holder out.
The bulb then pulls out from the holder. The first time I replaced the bulb it also was sticky and was a little difficult to pull, but it finally came out.
Replace the bulb, put the holder back into place and twist it clockwise to lock in.
Then replace the panel.
