Honda Accord EX

Since the VW Passat 1.8L engine has an Inherent Oil Sludge Problem, I would run an engine flush thru it.

Auto-RX I have heard nothing but good things about this product.

Once you get to the Rinse phase of the Auto-RX I would suggest using Castrol GTX 5W�30 and a Quality Wix Filter #51393.

Then once you have completed the Second Application and Step 5.

I would switch to a Full Synthetic designed to meet the VW Oil Standard 502.00 like AMSOIL's European Car Formula Synthetic 5W-40 Motor Oil (AFL) and a Quality Wix Filter #51393.

Models with 1.8L Engine codes AEB, ATW, AUG, AWM only use engine oil that conform to volkswagen oil standard VW 502.00 (with viscosities of SAE 5W-40, 5W-30 or 0W-40).

I would also on every other oil change use the Engine Flush Available from Amsoil. I would also keep a very detailed Maintenance log and all receipts.

I called VW the MAX oil change interval for the 1.8L engine is 5000 miles.

How to reset your Honda SRS light works on most models of Hondas

Directions for erasing memory on SRS light, but this procedure only works if all problems causing the indicator to be "on" have been corrected.

1st Obtain an 'SCS Service Connector'. You can use a speaker harness for an older Honda, which you can buy at any stereo shop such as Radio Shack, Circuit City or Best Buy. Cut the wires and loop them together. Or use a paperclip but that will make it a little more difficult, because you have to connect-and-disconnect it a few times quickly. 2nd you need to find the MES (Memory Erase Signal) this is located in or by the fuse box it is a yellow connection, remove it from the fuse box and jumper as described below. If there are 2 yellow connectors at the fuse box under the drivers side dash, look for the one with only 2 wires. That will be the one.

MES Plug is usually in or by the Fuse box.

It is a yellow connector with two wires in it that is plugged into the fuse box, unplug it and pull it down. Once you have done that you can begin the process of erasing the memory. NOTE: This will only reset your SRS System if what caused it to trigger has been fixed, Ex: turning the ignition on with any SRS Plugs disconnected, such as pulling your seat out.

1st step in erasing the memory is to turn the ignition off and connect the SCS Service connector to the MES Plug,

2nd Turn Ignition on. SRS indicator light will come on for about 6 seconds then go off.

3rd Disconnect SCS service connector for MES connector within 4 seconds after SRS indicator light goes off. SRS indicator light will come on again.

4th Reconnect SCS service connector the MES connector within 4 seconds after SRS light comes on. SRS indicator light will go off.

5th Disconnect SCS service connector from MES connector within 4 seconds. SRS indicator light will indicate that memory is erased by blinking 2 times.

6th Turn ignition off, and wait 10 seconds. Start vehicle like normal and light should come on and go out like normal. You have reset your SRS light, congrats.

If it does not work the first time try it again, the timing has to be perfect. My first time it took me 3 attempts before it worked, but it did work.

If this does not work and the light stays on then something is still wrong in the system.

Maybe the wire connection under the drivers seat or a fuse or bad ground or a bad clock spring (clock spring is under the driver side air bag).

Again, this procedure works only if all problems have been corrected. Good Luck!

I've seen people asking what it looks like,this is the picture of what it looks like on my 2001 Honda Accord V6, the small plug was the one for me. It did turn the SRS light off. Thank you

Can you tell me exactly what speaker harness you used for your 2001 Honda accord and exactly where I can get it? My 2001 accord shows the same small yellow plug for the MES, but I cannot find the right size speaker harness to connect to it. What store did you get it at, model number and year range of Honda's if you would?

This reset method works perfecty as described! I don't know if mine will come back on but it went out after I did this. Basicly just do the steps quickly and you will get it. Thanks to the posters of this trick!

Just use the paperclip or stiff wire, simple as can be. Don't sweat looking for a harness if you don't have one already.

thanks for your instruction, i followed it and it clear my SRS light for accord 98. It the small yellow connector with two green wires. I used a paper clip .

THE CONNECTION IS ON THE BACK SIDE OF THE DRIVER'S SIDE FUSE BOX ON THE 2000 V6 ACCORD. THE ONLY DIFFICULT PART WAS GETTING UNDER THE WHEEL TO UNINSTALL AND REINSTALL THE CONNECTOR. THE PAPER CLIP WORKS FINE. THANKS FOR THE TIP.

This answer was extremely helpful and I was able to reset the SRS memory in my 2000 Honda Accord in a minute. It was a piece of cake. For Honda Accord 2000 model, the MES plug is under the steering column. It's a small yellow plug with only two thin green wires in it. For this specific model (2000 Honda accord...) there's another plug right next to it with two green wires. Choose the small plug yellow plug out of these two. and after that.. it's really simple and can be done in half minute.

Thanks much for the answer again.

Thanks again for the answer!!!

Appreciate the !Hi guysThanks for the Tip! This answer was extremely helpful and it worked just like that on my 2000 Honda Accord in a minute.However, Light came back on after around 10 to 12 miles run. I reset it again, but the same thing. Light came back again after 10 to 12 miles.Any thoughts or any further suggestions?

This worked great on my 2003 Honda Pilot. Two things that may help others with this. First is on my 2003 pilot, the MES connector is located under the dash on the driver's left side in the fuse box. It is a yellow connector in the fuse box. Second, the MES connector is plugged into an emty socket just to hold it in place, not connected to any wires. A paperclip works fine, just stick it into the yellow plug you just pulled out. By the way, it was an old battery that caused the SRS light to come on in the first place so resetting fixed the problem. Thanks