0
Starters and Ignition Systems
Ignition systems are found in all complex engines. They are attached to a power source that provides both the power to the system and to the starters in order to turn on the engine.
3,433 Questions
2003 Ion click-no crank new starter and battery what's up?
Could be starter solenoid - Follow + battery cable should connect to solenoid
Ignition swtich?? Wiring ok from battery? Check all the grounds to engine and chassis... peek at a manual for a diagram// See if your local library has a professional shop manual to look at for free... dave
Most likely the ignition/key switch. Very common problem with ION.
Jim
Where is the ignition module on a 1993 Ford Probe 4 cylinder?
In the dist. Takeit to Auto zone and have them check it out.
Where is the starter on a 1997 sable?
If it's the 3 litre engine, the starter is at the front of the engine just a bit lower and to driver side of oil filter. Held on by 2 bolts from Trans side.
Where is the O2 sensor located on a 2001 Toyota sequoia?
Actually. there are four (4) of them on the Sequoia. The front two are located in the engine compartment on the exhaust headers. You can see them from underneath the car. One in either side exhuast header (left side and right side).
The rear two are located in the exhaust pipe system near the catalytic converter.
There is detailed information to be found in the FORUMS at tundrasolutions dotcom. This site has a VERY active Sequoia owners forum.
Where is the starter located on your 2001?
If you follow the positive battery cable, you should find it. Otherwise ask a new question and include the year, make, and model.
What is an ignition temperature?
the lowest temprature at which the fuel will burn on its own without the addition of external source of heat
Key stuck in ignition on your 406 Help please?
just had the same problem and it seams that it is the ignition switch behind the barrel but i am trying to find someone who knows where the relese pin is and in which position the key has to be in
There is no specific position where the key has to be.... It all happens when you switch off the car in turning position of the wheel. When ever you feel you are trying to ignit switch and looks like, it is lock or you are unalble to turn the switch on.... only turn your wheel and try again. That's it. Your key will be released enabling you to turn the key in order to ingnition...
How do you know which coil is bad on a 99 Monte Carlo if the car has a coil pack?
You can remove the suspect coil and switch it with a good coil and see if the two cylinders that were firing are now misfiring and the two that were misfiring are now firing.
If the coil pack is not working correctly then your car will be sluggish and should throw a misfire trouble code (check engine light). Usually only one coil will fail at a time. You can have the code scanned at autozone for free. They will also test your coils if you have them off the car. Always check your plugs and wires first before replacing the coil.
Why does my starter makes a ticking noise?
Most likely the ticking you are hearing is that from your solonoid. This is generally related with insufficient power from the battery.
You just need to get a 12 volt electric starter, it interchanges with the 110 volt starter. You should be able to use a starter from any 8 hp to 12 hp single cylinder flathead Briggs engine, 1970s to 1990s vintage. If you need the starter ring gear, you can purchase it as kit with mounting screws to attach to existing flywheel.
All sorts of things. Bad ignition system, which means ignition coil, distributor, wires, plugs... Could be fuel related. Clogged Filter, Clogged injectors, fuel pumps dying. Maybe clogged air filter. Could be mechanical. Idle Air Control Valve could be dying. EGR valve could be clogged. PCV Valve could be clogged. Maybe your Mass Airflow Sensor is dying. Some of those are a bit far fetched, but diagnosing rough idle is endless.
How do you replace ignition switch with no keys?
You do not need a key to replace the ignition switch.
How do you install an ignition switch on a 1989 Chevy truck 2500?
Hi there.
i own a 1989 Chevy cheyane and had to fix my tilt steering. the same applies to removing the steering wheel and etc to get to the ignition switch as well.
i went to Canadian tire or parts dealer. i had to rent a steering wheel puller etc. remove steering wheel cap, undo main bolt. remove plastic horn cover ( watch out for springs) remove tilt arm. then you have to remove torx screws from base of tilt housing. slide off main collar. you can search on the web for removing or fixing tilt mechanism and it will show you how to do this but it will show you how to remove the ignition system as well. it's not to hard just keep all the parts together and reasemble in same order you took apart. It took me two hours to do this, and i didnt know what i was doing.
good luck.
chris
How much does it usually cost to repair a starter?
The average cost to repair a starter is anywhere between $50 to $250 dollars. The starter is responsible for starting the car's engine.
How to replace ignition switch on a 1995 Dodge pickup?
Remove the plastic covering on the steering column. The ignition switch is the box that the ignition cylinder runs into. It's basically easy with only removing a couple of bolts to replace. The only trick is to be very careful actually pulling the box off the column. Make sure the key is in power off position. wiggle the box off, when putting the ignition cylinder into the new ignition switch you don't want to turn the key. Leave it in the off position. Then watch the rod in the rear of the new ignition switch as it goes back into the column. I have seen people have to turn the key in the ignition cylinder while pushing gently into the ignition switch. But beware it can turn into a real nightmare. If you use a bran new ignition cylinder, it will state all over do not turn the cylinder until it's installed.
Is a 1994 Saturn starter compatible with a 1995 Saturn car?
what you have to determine is if the engine is a DOHC (SC2, SL2, SW2) or SOHC (SC1, SL1, SW1) engine. they should be interchangable given the engine is the same.
Doesnt have to even be the same, single or dual have basically the same lower ends so you can swap any 1.9 Saturn starters.
How do you replace the ignition lock on a 92 grand prix?
GET "HAYNES" repair manual #38010 at your nearby auto parts store. It describes the process in detail and costs less than $20. This is too involved to describe here and you will need much patience. Forget about the "Chilton" books; they are worthless.
