Electric Windows

Anyway, the part# from napaonline.com is BK 6653601 for the drivers side (BK 6653602 for the passenger side).

Remove the door panel, time consuming but not too hard. Loosen the three 10mm bolts holding the motor in, remove the power connector.

Lower the window so that the two bolts holding it to the regulator are exposed, remove them. Push the window to the top, propping it at this position (a screwdriver through the access hole at the top left will prop on top of the exterior door handle keeping the window in place.

Remove the three 10mm bolts holding the regulator in place. 'Corkscrew' the regulator and motor out of the BIG hole at the back of the door.

Installation is the reverse of assembly.

EASY!

The Switch can be removed by gently prying under the switch flange with a small flat head screw driver. Take care not to damage the door panel. The switch should pop out fairly easily. The door panel does not need to be removed. The swith can then be separated from the wiring harness be simply depressing the orange tab on the harness socket. Plug the new switch into the harness and reinsert the switch into the top of the door panel.

anytime the window goes in either direction but will not go in the opposite direction, You know the motor is good,,,,, Now you need to know what is WRONG,It is most likely one of two things, The MOST likely is A bad switch, The second thing it might be is A damaged track inside the door, You can check this easy, Just try to go up with the glass if it does anything at all, you know the switch is working, So you need to check the track,,,,,, Another thing it could be is A bad wire on the power supply for the not working direction, BUT this is not likely unless you have A RAT! Good luck, Jamison.

i don know how would a monkey fix it

Take the outer door panel off then unbolt the old window from the track then place the new window in the track this will take sometime because the new window has to go in at an angle before you place the new window in the track make sure the track is at the bottom of the door use your hand tp place the window all the way down in the door then bring the window all the way up holding it with one hand at the bottom of the window you need to put the window all the way to the bottom first to make sure the window clips aline in the window track. roll the bottom of the track up intill you can bolt the new window in but be careful if you tighten down the window to tight it will break the put the door panel back on

Engine compartment, on passenger side. Back box by the water reservoirs.

yes

my suzuki vitara 2001 electric windows stopped working on the left side of the vehicle. What should I do?

Call the glass company and tell them.

this can be very tricky and involves drilling a hole to isolate the tension spring. i am a mechanic and had a co-worker tear the palm of his hand off because he did it wrong. pay someone to do this! cheepest and easyest way is to go get a new door from the junk yard and put on there and hook up

First, clean the inside glass COMPLETELY, then use an anti-fogging agent. You can get it at a parts store.

IF ALL WINDOWS HAVE STOPPED OPERATING AT ONE TIME YOU MOST PROBABLY HAVE A FUSE PROBLEM. IF THEY HAVE NOT ALL STOPPED OPERATING OR THEY HAVE STOPPED OPERATING AT DIFFERENT TIMES YOU PROBABLY HAVE POWER MOTOR PROBLEMS.

how do you run the wire for the power windows on a 91 Mazda miata

The exact cost to replace an electric window motor varies slightly by the model of car. As of 2014, the average cost for this motor is between 35 and 55 dollars.

i checked the front fuse box and two rear fuse boxes and none seem to have fuses for the windows. Any one have any suggestion's, thanks

If the vehicel is several years old, this could be due to a fatigues cable in the gaiter which connects the door to the door column. The solution to this questions is answered elsewhere in this web site. it could laso be due to a failed window switch. To check this, remove the window switch be 'leavering'it out of its recess and use a voltmeter to check that when the button is pressed, a votage appears on the appropriate terminal to operate the window. You can check this out by first operating a window which works.

you get plyers and yank it up

Hold down the child lock when you press the button to raise the window.

That is just how the vehicle is wired, its not a defect, its a safety feature, the windows arent supposed to work, unless the ignition is on.

First, check that the window lock switch is not pressed. It is on the drivers door next to the four power window switches, it has a little picture of a door and window on it with an X through it. If the switch is pressed, only the driver can open and shut the windows, the switches on the other doors will not work. If the windows won't work at all, not even from the driver's door, make sure the fuse for the power windows is good. Replace it if you don't know how to check it, fuses are cheap.

The driver's power window in the pilot has an auto up/down function, the rest do not. To use this, pull/push the window past the first 'stop' and if you let go, it will go all the way up or down automatically.

FIX:

1. Start the car and leave it idle.

2. Hold the window button down all the way, until the window is completely down.

3. Let go and push it down again and hold the window button for 2 to 3 seconds then let go. (You should be able to hear or feel (very faintly) the motor/sensor reset.)

4. Pull up on the window button and roll the window up until it is all the way up, when it is up let go.

5. Pull the button up again for 2 to 3 seconds. (You should be able to hear or feel (very faintly) the motor/sensor reset.)

The best explanation I have seen is found here: http://www.fullsizechevy.com/forums/general-discussion/tech-articles2/351094-99-02-nbs-power-window-regulator-motor-replacement.html It has pics that should help a lot.

I just found a fuse box under my hood in a black box with all kinds of fuses,in it there they were window fuses. what was the number and code please.?

If they are losing strenght, first try spraying silicone lube into the rubber weatherstrips where the window rides. A lot of times they become dry causing the windows to stick. If this does not help, unfurtunely you will have to replace the window motors. I have done many of these